Floor pump to keep in the car
#1
Full Member
Thread Starter
Join Date: Jul 2010
Location: Worcester, MA, USA
Posts: 411
Bikes: Dawes Lightning DLX, 1988 Klein Performance, 1991 Peugeot Safari, 1985 Raleigh Alyeska, Carrera Phantom, 1973 Raleigh Record
Mentioned: 1 Post(s)
Tagged: 0 Thread(s)
Quoted: 282 Post(s)
Liked 129 Times
in
92 Posts
Floor pump to keep in the car
I keep a humble Avenir Airsource One floor pump in the car, but it no longer clamps reliably on all my valve stems. I think I could fix it by replacing a specific rubber insert that gets compressed to grip the valve stem, but replacement parts don't seem to be available for it, so I'm looking for a new pump.
It should be relatively cheap and able to take the wear and tear of living in my trunk. I'd like a pump that I can get some replacement parts for, although that might be tough if I keep the pump for a decade or more. All my bikes have Presta stems, but I sometimes use my bike pump to top off the car tires, so a dual head is a plus. All my bikes use clincher tires with tubes and have max pressure ratings of 90 - 130psi (mostly 120-130).
Do you have any suggestions?
It should be relatively cheap and able to take the wear and tear of living in my trunk. I'd like a pump that I can get some replacement parts for, although that might be tough if I keep the pump for a decade or more. All my bikes have Presta stems, but I sometimes use my bike pump to top off the car tires, so a dual head is a plus. All my bikes use clincher tires with tubes and have max pressure ratings of 90 - 130psi (mostly 120-130).
Do you have any suggestions?
#2
Senior Member
Join Date: Sep 2014
Posts: 3,893
Mentioned: 20 Post(s)
Tagged: 0 Thread(s)
Quoted: 1062 Post(s)
Liked 665 Times
in
421 Posts
I've replaced just the head on old pumps with a different brand. The one sold by Park Tool seems to work, and won't break the bank. Another possibility is to get a pump head and hose combo for the existing pump.
Likes For Gresp15C:
#3
Senior Member
Join Date: Sep 2010
Location: Roswell, GA
Posts: 8,319
Bikes: '93 Trek 750, '92 Schwinn Crisscross, '93 Mongoose Alta
Mentioned: 30 Post(s)
Tagged: 0 Thread(s)
Quoted: 1438 Post(s)
Liked 1,092 Times
in
723 Posts
It sounds like you just need a new chuck. I put a Lezyne ABS2 chuck on my old Air Hammer pump (whose old chuck was never much good IMO) and like it a lot, but it does not seem to be available any more. The replacement seems to be this one: https://ride.lezyne.com/collections/...s1p-chuck-v111 It's sure a lot less than a whole new pump if just the chuck is problematic, although Lezyne makes nice pumps, too.
Likes For dsbrantjr:
#4
aged to perfection
Join Date: Jun 2009
Location: PacNW
Posts: 1,810
Bikes: Dinucci Allez 2.0, Richard Sachs, Alex Singer, Serotta, Masi GC, Raleigh Pro Mk.1, Hetchins, etc
Mentioned: 24 Post(s)
Tagged: 0 Thread(s)
Quoted: 835 Post(s)
Liked 1,252 Times
in
661 Posts
Find a used Silca of ebay, I grab them for under 25 bucks. put a rebuild kit into it and you have a pump you can pass on to your granddkids.
Or, I'll sell you one, fully rebuilt, for 65 + ship
Mark Petry
Bainbridge Island, WA USA
Or, I'll sell you one, fully rebuilt, for 65 + ship
Mark Petry
Bainbridge Island, WA USA
Likes For mpetry912:
#5
Senior Member
Join Date: Feb 2012
Location: Rochester, NY
Posts: 18,063
Bikes: Stewart S&S coupled sport tourer, Stewart Sunday light, Stewart Commuting, Stewart Touring, Co Motion Tandem, Stewart 3-Spd, Stewart Track, Fuji Finest, Mongoose Tomac ATB, GT Bravado ATB, JCP Folder, Stewart 650B ATB
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 4197 Post(s)
Liked 3,849 Times
in
2,300 Posts
My car pump is a SKS Compressor. Next to no plastic or O rings to melt/warp. While not the best at actual pumping (there has been a lot of pumping improvement in the last couple of decades, the SKS is a throw back to the Silca or MDI days) it is quite rugged and easily serviced. Mine has a Topeak Twinn Head chuck spliced onto the hose. Andy
__________________
AndrewRStewart
AndrewRStewart
#6
Senior Member
Join Date: May 2019
Location: Bloomington, IN
Posts: 2,945
Bikes: Paramount, Faggin, Ochsner, Ciocc, Basso
Mentioned: 116 Post(s)
Tagged: 0 Thread(s)
Quoted: 1303 Post(s)
Liked 1,908 Times
in
1,139 Posts
Rich,
contact me off line, I have a few Silca parts available that will fix your pump. Smiles, MH
contact me off line, I have a few Silca parts available that will fix your pump. Smiles, MH
#7
Really Old Senior Member
What not get a Schraeder to Presta adapter and a cheap 12V pump to run off the car?
https://www.acehardware.com/departme...E&gclsrc=aw.ds
https://www.acehardware.com/departme...E&gclsrc=aw.ds
#8
aka Tom Reingold
Join Date: Jan 2009
Location: New York, NY, and High Falls, NY, USA
Posts: 40,502
Bikes: 1962 Rudge Sports, 1971 Raleigh Super Course, 1971 Raleigh Pro Track, 1974 Raleigh International, 1975 Viscount Fixie, 1982 McLean, 1996 Lemond (Ti), 2002 Burley Zydeco tandem
Mentioned: 511 Post(s)
Tagged: 0 Thread(s)
Quoted: 7348 Post(s)
Liked 2,460 Times
in
1,432 Posts
Sometimes, the easiest way to change your chuck is to get one integrated with a new hose. Do that with your cheapest, worst floor pump. Then put it in your car. Your car is less demanding of pumps than your bike is. Car tires need much more volume, so you'll get a workout, but since they require lower pressure, you don't need a special pump.
__________________
Tom Reingold, tom@noglider.com
New York City and High Falls, NY
Blogs: The Experienced Cyclist; noglider's ride blog
“When man invented the bicycle he reached the peak of his attainments.” — Elizabeth West, US author
Please email me rather than PM'ing me. Thanks.
Tom Reingold, tom@noglider.com
New York City and High Falls, NY
Blogs: The Experienced Cyclist; noglider's ride blog
“When man invented the bicycle he reached the peak of his attainments.” — Elizabeth West, US author
Please email me rather than PM'ing me. Thanks.
Likes For noglider:
#10
Full Member
Thread Starter
Join Date: Jul 2010
Location: Worcester, MA, USA
Posts: 411
Bikes: Dawes Lightning DLX, 1988 Klein Performance, 1991 Peugeot Safari, 1985 Raleigh Alyeska, Carrera Phantom, 1973 Raleigh Record
Mentioned: 1 Post(s)
Tagged: 0 Thread(s)
Quoted: 282 Post(s)
Liked 129 Times
in
92 Posts
I didn't consider splicing in a chuck from a different pump or buying used. Those are both good suggestions. At a glance, it looks like a used Silca costs more than a new Topeak...
I have an otherwise perfectly good Specialized airtool sport that leaks air through the gauge. I could use the chuck from that.
I've never had good luck with 12VDC compressors, and I don't think they usually reach 130psi. I think I have one in the basement, though. Also, I drive a Saab; the cigarette lighter is only powered when the engine is running. It's a minor inconvenience, but it's an inconvenience.
I have an otherwise perfectly good Specialized airtool sport that leaks air through the gauge. I could use the chuck from that.
I've never had good luck with 12VDC compressors, and I don't think they usually reach 130psi. I think I have one in the basement, though. Also, I drive a Saab; the cigarette lighter is only powered when the engine is running. It's a minor inconvenience, but it's an inconvenience.
#11
Senior Member
Join Date: Sep 2014
Posts: 3,893
Mentioned: 20 Post(s)
Tagged: 0 Thread(s)
Quoted: 1062 Post(s)
Liked 665 Times
in
421 Posts
Indeed, I have an old Silca that I got for 5 bucks at St. Vinny's, with a Park Tool chuck. It had a reversible brass Presta / Schrader head that was just too fiddly, even with a new gasket, so the pump now has a Park Tool chuck on it from another pump (not Park Tool) that broke. Not vintage or authentic, but it should work for a long time. The gaskets wear out on all pump heads. I learned that you can get a second life out of the Park combination head, because the two gaskets are identical but reversed, so you just swap them when the Presta side gets too loose to stay on the valve stem.
Likes For Gresp15C:
#12
Senior Member
Join Date: Nov 2014
Location: Eugene, Oregon, USA
Posts: 27,547
Mentioned: 217 Post(s)
Tagged: 0 Thread(s)
Quoted: 18369 Post(s)
Liked 4,507 Times
in
3,350 Posts
I like to have a 12V compressor in the car just in case the car needs it. I have used them for bikes in the past, but probably mostly at lower pressures.
There are some rated for 200 or 300 lbs, and I think they'll do it for a small volume bike tire, but I have also had issues with doing large volumes at high pressures. Truck, trailer tires, etc.
There are some rated for 200 or 300 lbs, and I think they'll do it for a small volume bike tire, but I have also had issues with doing large volumes at high pressures. Truck, trailer tires, etc.
#13
Senior Member
Join Date: Aug 2005
Location: Pittsburgh, PA
Posts: 33,656
Bikes: '96 Litespeed Catalyst, '05 Litespeed Firenze, '06 Litespeed Tuscany, '20 Surly Midnight Special, All are 3x10. It is hilly around here!
Mentioned: 39 Post(s)
Tagged: 0 Thread(s)
Quoted: 2026 Post(s)
Likes: 0
Liked 1,096 Times
in
742 Posts
I bought a Bontrager "Charger" floor pump as an emergency replacement when my old Schwinn pump died while we were on vacation. It was the lowest cost decent pump the bike shop had at about $40. It has almost all metal construction, a dual Presta/Schrader chuck and a lifetime warranty. It's not small but appears quite durable.
Likes For HillRider:
#14
Really Old Senior Member
I like to have a 12V compressor in the car just in case the car needs it. I have used them for bikes in the past, but probably mostly at lower pressures.
There are some rated for 200 or 300 lbs, and I think they'll do it for a small volume bike tire, but I have also had issues with doing large volumes at high pressures. Truck, trailer tires, etc.
There are some rated for 200 or 300 lbs, and I think they'll do it for a small volume bike tire, but I have also had issues with doing large volumes at high pressures. Truck, trailer tires, etc.
A 2-1/2 gal. pancake compressor is very marginal for big tires.
#15
Senior Member
Join Date: Jan 2013
Location: Llano Estacado
Posts: 3,702
Bikes: old clunker
Mentioned: 13 Post(s)
Tagged: 0 Thread(s)
Quoted: 684 Post(s)
Likes: 0
Liked 105 Times
in
83 Posts
Why not fabricate or adapt a replacement seal? Find a suitable rubber washer in a hardware store, cut off a piece of rubber tubing of reasonable dimensions, etc.?
#16
aged to perfection
Join Date: Jun 2009
Location: PacNW
Posts: 1,810
Bikes: Dinucci Allez 2.0, Richard Sachs, Alex Singer, Serotta, Masi GC, Raleigh Pro Mk.1, Hetchins, etc
Mentioned: 24 Post(s)
Tagged: 0 Thread(s)
Quoted: 835 Post(s)
Liked 1,252 Times
in
661 Posts
I guess I mis understood the thrust of the question "pump to keep in the car".
if you are going to use a Silca or SKS pump to inflate car tires - you'll be pumping a long time.
also with car tires - at least modern ones, if they lose pressure you probably have a leak in which case you're much better off with a can of goop that will get you to the tire shop.
There are some really wonderful vintage Dunlop pumps that are high volume, foot operated units. I've never taken one apart so have no idea what the availability of replacement seals, etc might be. See below.
If on the other hand you want to inflate bike tires - well, there are many good suggestions above. I personally like the Silca b/c they are fully rebuildable and can thus last "forever". Which is a lot more than can be said for a $20 electric "device" from harbor freight or Walmart.
Mark Petry
Bainbridge Island, WA USA
if you are going to use a Silca or SKS pump to inflate car tires - you'll be pumping a long time.
also with car tires - at least modern ones, if they lose pressure you probably have a leak in which case you're much better off with a can of goop that will get you to the tire shop.
There are some really wonderful vintage Dunlop pumps that are high volume, foot operated units. I've never taken one apart so have no idea what the availability of replacement seals, etc might be. See below.
If on the other hand you want to inflate bike tires - well, there are many good suggestions above. I personally like the Silca b/c they are fully rebuildable and can thus last "forever". Which is a lot more than can be said for a $20 electric "device" from harbor freight or Walmart.
Mark Petry
Bainbridge Island, WA USA
Likes For mpetry912:
#18
aged to perfection
Join Date: Jun 2009
Location: PacNW
Posts: 1,810
Bikes: Dinucci Allez 2.0, Richard Sachs, Alex Singer, Serotta, Masi GC, Raleigh Pro Mk.1, Hetchins, etc
Mentioned: 24 Post(s)
Tagged: 0 Thread(s)
Quoted: 835 Post(s)
Liked 1,252 Times
in
661 Posts
I have been tempted to buy one just to see how they are built. An interesting gizmo for the workshop... like I don't have enough of those already !
Mark Petry
Bainbridge Island, WA USA
Mark Petry
Bainbridge Island, WA USA
#19
Senior Member
Join Date: Sep 2010
Location: Roswell, GA
Posts: 8,319
Bikes: '93 Trek 750, '92 Schwinn Crisscross, '93 Mongoose Alta
Mentioned: 30 Post(s)
Tagged: 0 Thread(s)
Quoted: 1438 Post(s)
Liked 1,092 Times
in
723 Posts
Most floor pumps use standard 1/8" NPT threaded gauges. I have replaced 120-160psi gauges with lower-pressure ones more suited to the pressures I run, you could certainly replace a leaking gauge with an inexpensive gauge from EBay, etc.
Likes For dsbrantjr:
#20
Full Member
Thread Starter
Join Date: Jul 2010
Location: Worcester, MA, USA
Posts: 411
Bikes: Dawes Lightning DLX, 1988 Klein Performance, 1991 Peugeot Safari, 1985 Raleigh Alyeska, Carrera Phantom, 1973 Raleigh Record
Mentioned: 1 Post(s)
Tagged: 0 Thread(s)
Quoted: 282 Post(s)
Liked 129 Times
in
92 Posts
I guess I mis understood the thrust of the question "pump to keep in the car".
if you are going to use a Silca or SKS pump to inflate car tires - you'll be pumping a long time.
also with car tires - at least modern ones, if they lose pressure you probably have a leak in which case you're much better off with a can of goop that will get you to the tire shop.
if you are going to use a Silca or SKS pump to inflate car tires - you'll be pumping a long time.
also with car tires - at least modern ones, if they lose pressure you probably have a leak in which case you're much better off with a can of goop that will get you to the tire shop.
"Pumping a long time" depends how much air you're trying to put in the tire. If you're only trying to bring it up 2-5 psi it's not bad.