Old Dura Ace Freewheel
#1
Senior Member
Thread Starter
Join Date: Nov 2014
Location: Saratoga calif.
Posts: 1,049
Bikes: Miyata 610(66cm), GT Vantara Hybrid (64cm), Nishiki International (64cm), Peugeot rat rod (62 cm), Trek 800 Burning Man helicopter bike, Bob Jackson frame (to be restored?) plus a never ending stream of neglected waifs from the Bike exchange.
Mentioned: 28 Post(s)
Tagged: 0 Thread(s)
Quoted: 339 Post(s)
Likes: 0
Liked 632 Times
in
229 Posts
Old Dura Ace Freewheel
I was loooking through some used freewheels yesterday and noticed 2 I hadn't seen before. The first was a Dura Ace and the second was Shimano 600. They both pre date the hyperglides.
My question, Are they any better than the standard Shimano freewheels of that era and if so how?
In this case I went with a 7 speed Suntour unit, the one with 4 notches for the removal tool . This unit was the same height as a 6 speed freewheel , A compact version with smaller spacing?
It fits in the 126mm Dropouts of the bike I am fixing without having to stretch the stays apart.
My question, Are they any better than the standard Shimano freewheels of that era and if so how?
In this case I went with a 7 speed Suntour unit, the one with 4 notches for the removal tool . This unit was the same height as a 6 speed freewheel , A compact version with smaller spacing?
It fits in the 126mm Dropouts of the bike I am fixing without having to stretch the stays apart.
#2
working on my sandal tan
Join Date: Aug 2011
Location: CID
Posts: 22,629
Bikes: 1991 Bianchi Eros, 1964 Armstrong, 1988 Diamondback Ascent, 1988 Bianchi Premio, 1987 Bianchi Sport SX, 1980s Raleigh mixte (hers), All-City Space Horse (hers)
Mentioned: 98 Post(s)
Tagged: 0 Thread(s)
Quoted: 3871 Post(s)
Liked 2,571 Times
in
1,579 Posts
In this case I went with a 7 speed Suntour unit, the one with 4 notches for the removal tool . This unit was the same height as a 6 speed freewheel , A compact version with smaller spacing?
It fits in the 126mm Dropouts of the bike I am fixing without having to stretch the stays apart.
It fits in the 126mm Dropouts of the bike I am fixing without having to stretch the stays apart.
#3
Senior Member
Join Date: Nov 2014
Location: Eugene, Oregon, USA
Posts: 27,547
Mentioned: 217 Post(s)
Tagged: 0 Thread(s)
Quoted: 18389 Post(s)
Liked 4,520 Times
in
3,359 Posts
I've come to dislike freewheels with the notches for removal tools. I probably still have a couple around somewhere.
Make sure you clamp the tool down in the quick release tightly before trying to remove.
Make sure you clamp the tool down in the quick release tightly before trying to remove.
#4
Senior Member
Join Date: Feb 2012
Location: Rochester, NY
Posts: 18,102
Bikes: Stewart S&S coupled sport tourer, Stewart Sunday light, Stewart Commuting, Stewart Touring, Co Motion Tandem, Stewart 3-Spd, Stewart Track, Fuji Finest, Mongoose Tomac ATB, GT Bravado ATB, JCP Folder, Stewart 650B ATB
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 4214 Post(s)
Liked 3,889 Times
in
2,321 Posts
Dura Ace was the "best" level of manufacturing that Shimano offered. The best materials, most precise and accurate fabrication and nicest finish. So that DA freewheel might have longer lasting bearings and/or cogs, might weigh a tad less for the same cog range and might be smoother in function. "might" because the differences are not major ones and steel still wears over time.
The 600 (now Ultegra) level uses many of the design elements that DA does but at a lower cost then DA is. Still regarded as a better then average part. Andy
The 600 (now Ultegra) level uses many of the design elements that DA does but at a lower cost then DA is. Still regarded as a better then average part. Andy
__________________
AndrewRStewart
AndrewRStewart
#5
Really Old Senior Member
Just take the slop out and concentrate on keeping your rotating force on the proper plane and centered.
I'm not a fan of the 2/4 prong tools either, but you have to do what you have to do.
I won't put those FW's on a bike I expect to see again.
#6
Senior Member
Thread Starter
Join Date: Nov 2014
Location: Saratoga calif.
Posts: 1,049
Bikes: Miyata 610(66cm), GT Vantara Hybrid (64cm), Nishiki International (64cm), Peugeot rat rod (62 cm), Trek 800 Burning Man helicopter bike, Bob Jackson frame (to be restored?) plus a never ending stream of neglected waifs from the Bike exchange.
Mentioned: 28 Post(s)
Tagged: 0 Thread(s)
Quoted: 339 Post(s)
Likes: 0
Liked 632 Times
in
229 Posts
I actually compared 3 seven speed freewheels to a six speed. Two of them , chinese hyperglide copies , were about 2-3 mm wider. The Suntour 7 speed was virtually the same width.
#7
Senior Member
Join Date: Jun 2018
Location: SW Ohio
Posts: 2,398
Mentioned: 93 Post(s)
Tagged: 0 Thread(s)
Quoted: 1105 Post(s)
Liked 1,825 Times
in
878 Posts
I agree. I use the skewer (leaving it a tiny bit loose) to make sure the tool doesn't slip out and then put the tool in a vise. It's a lot easier to the use the wheel as a lever as opposed to a wrench. Once it breaks, loosen the skewer so it doesn't get jammed on the wheel.
#8
Old fart
Join Date: Nov 2004
Location: Appleton WI
Posts: 24,800
Bikes: Several, mostly not name brands.
Mentioned: 153 Post(s)
Tagged: 0 Thread(s)
Quoted: 3594 Post(s)
Liked 3,403 Times
in
1,936 Posts
Dura-Ace freewheels, IMHO, are among the best ever made. My favorites are the later models with the Uniglide tooth profile and splined remover tool. Earlier Dura-Ace freewheels were mechanically excellent, but had standard tooth profiles that didn't shift as easily as the Uniglide teeth. The early freewheels also used a two-prong remover (compatible with the Regina/Everest/etc. two prong standard) that is not as sturdy as the later splined remover.