Go Back  Bike Forums > Bike Forums > General Cycling Discussion
Reload this Page >

Gear change progression?

Notices
General Cycling Discussion Have a cycling related question or comment that doesn't fit in one of the other specialty forums? Drop on in and post in here! When possible, please select the forum above that most fits your post!

Gear change progression?

Old 08-09-20, 08:57 AM
  #1  
kaiserschmarrn
Junior Member
Thread Starter
 
Join Date: Apr 2020
Posts: 136
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 41 Post(s)
Liked 9 Times in 8 Posts
Gear change progression?

How do you figure out what your gear change progression, for possible lack of a better term, should be on a given bike? What I mean is, how do you figure out exactly which gear combinatiions that you should use as you progress upwards, so that you do not choose redundant gears, or maybe even drop down while shifting up?

Thanks,

Danny
kaiserschmarrn is offline  
Old 08-09-20, 09:04 AM
  #2  
Litespud
Senior Member
 
Join Date: Oct 2017
Location: Chapel Hill NC
Posts: 1,683

Bikes: 2000 Litespeed Vortex Chorus 10, 1995 DeBernardi Cromor S/S

Mentioned: 4 Post(s)
Tagged: 0 Thread(s)
Quoted: 645 Post(s)
Liked 797 Times in 446 Posts
Originally Posted by kaiserschmarrn
How do you figure out what your gear change progression, for possible lack of a better term, should be on a given bike? What I mean is, how do you figure out exactly which gear combinatiions that you should use as you progress upwards, so that you do not choose redundant gears, or maybe even drop down while shifting up?

Thanks,

Danny
there’s a decent gear calculator here:
Bicycle Gear Calculator
plug in your own setup and it’ll show you how the various combinations stack up
Litespud is offline  
Old 08-09-20, 09:20 AM
  #3  
Homebrew01
Super Moderator
 
Homebrew01's Avatar
 
Join Date: Jul 2004
Location: Ffld Cnty Connecticut
Posts: 21,844

Bikes: Old Steelies I made, Old Cannondales

Mentioned: 12 Post(s)
Tagged: 0 Thread(s)
Quoted: 1173 Post(s)
Liked 921 Times in 608 Posts
I generally shift 1 at a time, harder or easier as terrain changes.
The front chainrings are like "High" and "Low" range.
Lots of short hills near me, so I am in the small chainring most of the time.
i shift to the large ring if I have extended time on flat roads or longer downhills.

I have no idea which gears overlap, not really relevant when riding.

Whichever gear keeps my RPM in the 85 - 95 range
__________________
Bikes: Old steel race bikes, old Cannondale race bikes, less old Cannondale race bike, crappy old mtn bike.

FYI: https://www.bikeforums.net/forum-sugg...ad-please.html
Homebrew01 is offline  
Likes For Homebrew01:
Old 08-09-20, 09:35 AM
  #4  
genejockey 
Klaatu..Verata..Necktie?
 
genejockey's Avatar
 
Join Date: May 2007
Location: SF Bay Area
Posts: 17,649

Bikes: Litespeed Ultimate, Ultegra; Canyon Endurace, 105; Battaglin MAX, Chorus; Bianchi 928 Veloce; Ritchey Road Logic, Dura Ace; Cannondale R500 RX100; Schwinn Circuit, Sante; Lotus Supreme, Dura Ace

Mentioned: 41 Post(s)
Tagged: 0 Thread(s)
Quoted: 10241 Post(s)
Liked 11,593 Times in 5,942 Posts
Originally Posted by Homebrew01
I generally shift 1 at a time, harder or easier as terrain changes.
The front chainrings are like "High" and "Low" range.
Lots of short hills near me, so I am in the small chainring most of the time.
i shift to the large ring if I have extended time on flat roads or longer downhills.

I have no idea which gears overlap, not really relevant when riding.

Whichever gear keeps my RPM in the 85 - 95 range
That's really all there is to it. You figure out what cadence and load you're comfortable at and just change up or down to keep yourself there. Occasionally look down to make sure you're not cross-chaining, but mostly it gets noisy when you do, so you'll find yourself looking down anyway.

Over time, you'll get a feeling for how far to go up or down when the grade changes, so you'll shift into bigger gears (meaning smaller cogs) as you summit, or shift into smaller gears (meaning bigger cogs) as you lose momentum going up a hill. You'll also figure out how many cogs you need to go up or down when you change from one chainring to another in the front. Some of my bikes, with 53/39, it's two. The 50/34 and 52/36, it's 3.

The key is not overthinking. I generally couldn't tell you what gear I'm in, till I'm in either the largest or smallest and can't go any further.
__________________
"Don't take life so serious-it ain't nohow permanent."

"Everybody's gotta be somewhere." - Eccles
genejockey is offline  
Old 08-09-20, 09:35 AM
  #5  
Mulberry20
Senior Member
 
Join Date: Jun 2016
Posts: 733
Mentioned: 2 Post(s)
Tagged: 0 Thread(s)
Quoted: 440 Post(s)
Liked 199 Times in 136 Posts
When deciding what pornography was, a justice on the Supreme Court stated “you know it when you see it”, so in this case “you know it when you feel it”.
Mulberry20 is offline  
Likes For Mulberry20:
Old 08-09-20, 09:53 AM
  #6  
rydabent
Banned
 
Join Date: Apr 2010
Location: Lincoln Ne
Posts: 9,924

Bikes: RANS Stratus TerraTrike Tour II

Mentioned: 46 Post(s)
Tagged: 0 Thread(s)
Quoted: 3352 Post(s)
Liked 1,054 Times in 634 Posts
Back in the days of the 10 speeds, a rider had to do a few double shifts to get progression. That meant he had to shift both the derailer and the chain rings. Really dumb IMO.

As I have posted before especially if you have a front triple, look at it this way. Granny for hills, center ring for most riding, and the big ring for down hills or with the wind. Pick one of the three and simply shift across the rear cluster. That may not work well on some short chain stay DF bikes but it does work well on bents.
rydabent is offline  
Likes For rydabent:
Old 08-09-20, 10:07 AM
  #7  
Retro Grouch 
Senior Member
 
Retro Grouch's Avatar
 
Join Date: Feb 2004
Location: St Peters, Missouri
Posts: 30,225

Bikes: Catrike 559 I own some others but they don't get ridden very much.

Mentioned: 16 Post(s)
Tagged: 0 Thread(s)
Quoted: 1572 Post(s)
Liked 642 Times in 363 Posts
Originally Posted by rydabent
Back in the days of the 10 speeds, a rider had to do a few double shifts to get progression. That meant he had to shift both the derailer and the chain rings. Really dumb IMO.

As I have posted before especially if you have a front triple, look at it this way. Granny for hills, center ring for most riding, and the big ring for down hills or with the wind. Pick one of the three and simply shift across the rear cluster. That may not work well on some short chain stay DF bikes but it does work well on bents.
My philosophy exactly.
__________________
My greatest fear is all of my kids standing around my coffin and talking about "how sensible" dad was.
Retro Grouch is offline  
Old 08-09-20, 10:49 AM
  #8  
fietsbob
Banned
 
Join Date: Jun 2010
Location: NW,Oregon Coast
Posts: 43,598

Bikes: 8

Mentioned: 197 Post(s)
Tagged: 0 Thread(s)
Quoted: 7607 Post(s)
Liked 1,354 Times in 861 Posts
Internal gear hubs do the ratio sequencing for you.

Hence I found them Ideal in the heavy rain, as I wear a cycling rain cape , blocking my view of looking down,
to see what gear ratio combination I'm in..

Sheldon gears is another calculating program ... chain-wheel & cog combinations determine the IGH range Low & High..

That Option is offered on that site.






...
fietsbob is offline  
Old 08-09-20, 02:07 PM
  #9  
70sSanO
Senior Member
 
70sSanO's Avatar
 
Join Date: Feb 2015
Location: Mission Viejo
Posts: 5,768

Bikes: 1986 Cannondale SR400 (Flat bar commuter), 1988 Cannondale Criterium XTR, 1992 Serotta T-Max, 1995 Trek 970

Mentioned: 20 Post(s)
Tagged: 0 Thread(s)
Quoted: 1935 Post(s)
Liked 2,148 Times in 1,312 Posts
I probably view things a bit differently than some. My road bike as a triple and mountain bike as a double. My goal is to shift chainrings as little as possible.

I ride in 48 or 38 on my road bike and only use the 30 chainring when I really have to.

Mountain bike 34/24 and depending on the terrain, I’ll run in one or the other; mostly climbing 24, mostly flat or downhill 34.

I like my cassettes to be wide enough to let me stay in one ring as much as I can. This is not quite like having multiple 1x setups because I use fewer cogs

Years ago half step gearing was used with 5 speed freewheels, but 1x10, 11, 12 have eliminated the need.
70sSanO is offline  
Old 08-09-20, 02:24 PM
  #10  
shelbyfv
Expired Member
 
shelbyfv's Avatar
 
Join Date: Jun 2007
Location: TN
Posts: 11,453
Mentioned: 37 Post(s)
Tagged: 0 Thread(s)
Quoted: 3634 Post(s)
Liked 5,310 Times in 2,698 Posts
I don't believe I've ever done much pondering about this. I shift up and down the cassette as needed, shift the front when I spin out or something rubs. Admittedly not very thoughtful. Maybe there are subconscious choices being made?
shelbyfv is offline  
Likes For shelbyfv:
Old 08-09-20, 02:35 PM
  #11  
caloso
Senior Member
 
caloso's Avatar
 
Join Date: Jul 2002
Location: Sacramento, California, USA
Posts: 40,865

Bikes: Specialized Tarmac, Canyon Exceed, Specialized Transition, Ellsworth Roots, Ridley Excalibur

Mentioned: 68 Post(s)
Tagged: 0 Thread(s)
Quoted: 2952 Post(s)
Liked 3,106 Times in 1,417 Posts
I try not to overthink it. As long as I’m not cross chaining, it’s not supercritical.
caloso is offline  
Old 08-09-20, 03:26 PM
  #12  
JohnDThompson 
Old fart
 
JohnDThompson's Avatar
 
Join Date: Nov 2004
Location: Appleton WI
Posts: 24,934

Bikes: Several, mostly not name brands.

Mentioned: 153 Post(s)
Tagged: 0 Thread(s)
Quoted: 3571 Post(s)
Liked 3,366 Times in 1,915 Posts
Originally Posted by rydabent
Back in the days of the 10 speeds, a rider had to do a few double shifts to get progression. That meant he had to shift both the derailer and the chain rings. Really dumb IMO.
Only if you're OCD enough to insist on always following a strict, linear progression. I don't, anymore. If I need a little change, I shift the rear derailleur. If I need a bigger change, I shift the front. I don't much care if the gear I land in is the next one in the sequence.
JohnDThompson is offline  
Likes For JohnDThompson:
Old 08-09-20, 03:27 PM
  #13  
fietsbob
Banned
 
Join Date: Jun 2010
Location: NW,Oregon Coast
Posts: 43,598

Bikes: 8

Mentioned: 197 Post(s)
Tagged: 0 Thread(s)
Quoted: 7607 Post(s)
Liked 1,354 Times in 861 Posts
basic Math

front T number turns cog T number in a ratio.. eg 44:22 - 2:1

. multiply that by diameter of wheel typically inches,

optionally calculate circumference

gives you how far you go every crank rotation,
fietsbob is offline  
Old 08-09-20, 03:40 PM
  #14  
DaveSSS 
Senior Member
 
Join Date: Sep 2008
Location: Loveland, CO
Posts: 7,212

Bikes: Cinelli superstar disc, two Yoeleo R12

Mentioned: 3 Post(s)
Tagged: 0 Thread(s)
Quoted: 1090 Post(s)
Liked 554 Times in 443 Posts
The big ring is used until the next to largest sprocket is used. If you need a lower/slower gear change to the little ring, usually followed by shifting 1 to 3 sprockets smaller. I always shift 2 and then adjust from there. If you get too bogged down before shifting to the little ring, no sprocket shifts may be needed.
DaveSSS is offline  
Likes For DaveSSS:
Old 08-09-20, 07:51 PM
  #15  
scott967
Senior Member
 
Join Date: Oct 2013
Location: Oahu, HI
Posts: 1,396

Bikes: 89 Paramount OS 84 Fuji Touring Series III New! 2013 Focus Izalco Ergoride

Mentioned: 2 Post(s)
Tagged: 0 Thread(s)
Quoted: 285 Post(s)
Likes: 0
Liked 74 Times in 54 Posts
I have a touring with a 50-45-28 triple. That one needs a bit of thinking as there are so many equivalent (or close to) ratios. But on a 53-39, or 50-34 in my old age it doesn't take me long to have a feel for what ring I should be in and then the cassette just follows naturally. I think the bigger question is more personal -- get a wider ratio cassette so you spend all your time except climbing in the big ring, or a close ratio cassette and get a feel for when it's best to change rings. I do use big big sometimes just to get over a hump.

scott s.
.
scott967 is offline  
Old 08-10-20, 04:30 AM
  #16  
livedarklions
Tragically Ignorant
 
livedarklions's Avatar
 
Join Date: Jun 2018
Location: New England
Posts: 15,613

Bikes: Serotta Atlanta; 1994 Specialized Allez Pro; Giant OCR A1; SOMA Double Cross Disc; 2022 Allez Elite mit der SRAM

Mentioned: 62 Post(s)
Tagged: 0 Thread(s)
Quoted: 8186 Post(s)
Liked 9,094 Times in 5,053 Posts
Originally Posted by fietsbob
front T number turns cog T number in a ratio.. eg 44:22 - 2:1

. multiply that by diameter of wheel typically inches,

optionally calculate circumference

gives you how far you go every crank rotation,
I can't count the number of times I've had to stop in the middle of a climb so I can calculate the best gear ratio.

This is a pretty silly thread.
livedarklions is offline  
Likes For livedarklions:
Old 08-10-20, 06:05 AM
  #17  
roth rothar
Senior Member
 
roth rothar's Avatar
 
Join Date: Jul 2020
Location: Massachusetts
Posts: 57

Bikes: Raleigh Technium, Cannodale SR600,Trek 520, Specialized Rock Hopper, Scott CR1 Pro

Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 18 Post(s)
Liked 21 Times in 11 Posts
Use the Popeye method: 53x11 and a can of Spinach
roth rothar is offline  
Likes For roth rothar:
Old 08-10-20, 06:33 AM
  #18  
Moe Zhoost
Half way there
 
Moe Zhoost's Avatar
 
Join Date: Sep 2015
Location: North Carolina
Posts: 2,955

Bikes: Many, and the list changes frequently

Mentioned: 5 Post(s)
Tagged: 0 Thread(s)
Quoted: 985 Post(s)
Liked 879 Times in 526 Posts
Make it easy on yourself and go to a 1x setup. If you insist on multiple chain rings in the front, half-step gearing is marvelous. Yes, you have to overcome a distaste for shifting with your left hand, but half-step eliminates a lot of redundant combinations and also allows a logical progression through the gears.
Moe Zhoost is offline  
Old 08-10-20, 07:55 AM
  #19  
xroadcharlie
Senior Member
 
Join Date: Apr 2019
Location: Windsor Ontario, Canada
Posts: 531

Bikes: 2018 Giant Sedona

Mentioned: 1 Post(s)
Tagged: 0 Thread(s)
Quoted: 179 Post(s)
Liked 116 Times in 95 Posts
Originally Posted by livedarklions
I can't count the number of times I've had to stop in the middle of a climb so I can calculate the best gear ratio.

This is a pretty silly thread.
That's why you should bring a cheat sheet, or write some numbers on your hand like you did for a high school test. This way you just have to find the right numbers to choose the correct gear, Hopefully before you crash into the trees.

But seriously, with my triple chainring I just pick the one that I anticipate I might need soon if its important, Like climbing or for quick acceleration.

This works best if the cassette cogs are spaced correctly. For me, that's a 10- 13% increase with each up tick

My 1'st derailleur bike was a 10 speed racer with a 2 x 5 speed drivetrain. Because the 5 rear cogs were spaced widely apart, The engineer who designed the bike chose to use chainrings that would put a step between each rear cog. So while the single shift was a bit higher then ideal, If it bothered me, I could always find the next gear up or down. With just 2 chainring's it's easy to do.
xroadcharlie is offline  
Old 08-10-20, 08:54 AM
  #20  
livedarklions
Tragically Ignorant
 
livedarklions's Avatar
 
Join Date: Jun 2018
Location: New England
Posts: 15,613

Bikes: Serotta Atlanta; 1994 Specialized Allez Pro; Giant OCR A1; SOMA Double Cross Disc; 2022 Allez Elite mit der SRAM

Mentioned: 62 Post(s)
Tagged: 0 Thread(s)
Quoted: 8186 Post(s)
Liked 9,094 Times in 5,053 Posts
Originally Posted by roth rothar
Use the Popeye method: 53x11 and a can of Spinach

I can never seriously give people gearing advice because I'm a genetic freak who cruises best at level in 53X11 or 53x12. I'm also a huge fan of the 1930s-1940s Popeye cartoons, but I'm really not that into spinach.

My basic method is ride in highest gear then gear down for hills, headwinds, and sometimes heat. This will not work for most people, and I've had to listen with amusement to people telling me it can't possibly be working for me. Apparently, if I do it another 50 years, I WILL blow out my knees.
livedarklions is offline  
Old 08-10-20, 09:01 AM
  #21  
WarrenR
Junior Member
 
Join Date: Aug 2014
Location: Halifax, NS
Posts: 192

Bikes: 2005 Peugeot Evasion 2019 Trek Verve

Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 18 Post(s)
Liked 19 Times in 17 Posts
Small chainring, 1 2 3, middle chainring 3 4 5 6, large chaining 6 7 8.
Pretty simple
WarrenR is offline  
Old 08-10-20, 09:12 AM
  #22  
Retro Grouch 
Senior Member
 
Retro Grouch's Avatar
 
Join Date: Feb 2004
Location: St Peters, Missouri
Posts: 30,225

Bikes: Catrike 559 I own some others but they don't get ridden very much.

Mentioned: 16 Post(s)
Tagged: 0 Thread(s)
Quoted: 1572 Post(s)
Liked 642 Times in 363 Posts
Originally Posted by JohnDThompson
Only if you're OCD enough to insist on always following a strict, linear progression. I don't, anymore. If I need a little change, I shift the rear derailleur. If I need a bigger change, I shift the front. I don't much care if the gear I land in is the next one in the sequence.
Gonna take Rideabent's side on this one. Back in the 2 X 5 days I used to fiddle with my right hand on both shift levers until I stumbled into the gear that came closest to hitting the "sweet spot." Interestingly, I found it more annoying not to find the "right" gear on a flat road than if I were riding hills. At the time I lived in NW Indiana which was mostly the top of a table.
__________________
My greatest fear is all of my kids standing around my coffin and talking about "how sensible" dad was.
Retro Grouch is offline  
Old 08-10-20, 09:19 AM
  #23  
Reflector Guy
Senior Member
 
Reflector Guy's Avatar
 
Join Date: Jul 2020
Location: Chicago
Posts: 1,340

Bikes: Bianchi Infinito XE, Via Nirone 7, GT Aggressor Pro

Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 599 Post(s)
Liked 1,270 Times in 588 Posts
In front, I use the large chainring about 95% of the time. The smaller one only gets used for steep climbs, riding slowly (on sidewalks, for example), getting started across a busy street after a stop, etc. Once I get going I'm right back into the big ring and I shift from gear to gear (large to small) in the back as I increase speed. Pretty simple really. I am sure most people do similar.

Some day I should try a triple-chainring bike. That extra sprocket will probably blow my mind!

Last edited by Reflector Guy; 08-10-20 at 09:23 AM.
Reflector Guy is offline  
Old 08-10-20, 09:35 AM
  #24  
fietsbob
Banned
 
Join Date: Jun 2010
Location: NW,Oregon Coast
Posts: 43,598

Bikes: 8

Mentioned: 197 Post(s)
Tagged: 0 Thread(s)
Quoted: 7607 Post(s)
Liked 1,354 Times in 861 Posts
BITD, simpler times, when asked what gear are you in the reply was like " my 42:16" ..







fietsbob is offline  
Old 08-10-20, 10:18 AM
  #25  
Altair 4
Senior Member
 
Join Date: Nov 2010
Location: Along the Rivers of Pittsburgh
Posts: 1,255

Bikes: 2011 Novara Forza Hybrid, 2005 Trek 820, 1989 Cannondale SR500 Black Lightning, 1975 Mundo Cycles Caloi Racer

Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 258 Post(s)
Liked 291 Times in 157 Posts
I'm in the middle chainring of my triple about 95% of the time. I shift the rear to get to the "that feels right" gear as terrain, wind, and my general attitude dictate.
Altair 4 is offline  
Likes For Altair 4:

Thread Tools
Search this Thread

Contact Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service -

Copyright © 2024 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.