Removing Powder Coating
#2
Senior Member
Join Date: May 2012
Location: Point Reyes Station, California
Posts: 4,527
Bikes: Indeed!
Mentioned: 92 Post(s)
Tagged: 0 Thread(s)
Quoted: 1507 Post(s)
Liked 3,469 Times
in
1,131 Posts
I didn't have much success with paint stripper. I ended up using a 4" angle grinder with a wire wheel. A lot of work and I still had to do a lot of sanding and scraping by hand in those hard-to-reach spots. I too hope someone has a better solution.
Brent
Brent
Likes For Kilroy1988:
#4
Senior Member
Join Date: Jul 2018
Location: Okanagan Valley, British Columbia
Posts: 50
Bikes: ‘84 Alan sprint, Rocky Mountain Altitude 799, Trek fuel ex 9.9, Gardin/Battaglin’84, Nishiki international ‘83, ‘86 panasonic dx5000, 93 mongoose amplifier
Mentioned: 2 Post(s)
Tagged: 0 Thread(s)
Quoted: 14 Post(s)
Liked 30 Times
in
13 Posts
Acetone will remove powder coat, I found this out the hard way. Though you would need a lot to strip an entire frame.
B.
B.
#6
Senior Member
Join Date: Mar 2013
Location: Maryland
Posts: 3,799
Bikes: Lots of English 3-speeds, a couple of old road bikes, 3 mountain bikes, 1 hybrid, and a couple of mash-ups
Mentioned: 53 Post(s)
Tagged: 0 Thread(s)
Quoted: 887 Post(s)
Liked 335 Times
in
225 Posts
Powder coat is really tough stuff. I have no advice, but good luck.
#7
Senior Member
Join Date: Jun 2018
Location: The Urban Shores Of Michigami
Posts: 1,749
Bikes: ........................................ .....Holdsworth "Special"..... .......Falcon "Special".......... .........Miyata 912........... ........................................
Mentioned: 11 Post(s)
Tagged: 0 Thread(s)
Quoted: 702 Post(s)
Liked 672 Times
in
420 Posts
#8
Senior Member
Join Date: Mar 2013
Location: Maryland
Posts: 3,799
Bikes: Lots of English 3-speeds, a couple of old road bikes, 3 mountain bikes, 1 hybrid, and a couple of mash-ups
Mentioned: 53 Post(s)
Tagged: 0 Thread(s)
Quoted: 887 Post(s)
Liked 335 Times
in
225 Posts
#9
Bianchi Goddess
Join Date: Apr 2009
Location: Shady Pines Retirement Fort Wayne, In
Posts: 27,858
Bikes: Too many to list here check my signature.
Mentioned: 192 Post(s)
Tagged: 2 Thread(s)
Quoted: 2930 Post(s)
Liked 2,923 Times
in
1,491 Posts
"Just the frame" considering how hard stripping paint can be this may be a lifetime quest.
__________________
“One morning you wake up, the girl is gone, the bikes are gone, all that's left behind is a pair of old tires and a tube of tubular glue, all squeezed out"
Sugar "Kane" Kowalczyk
“One morning you wake up, the girl is gone, the bikes are gone, all that's left behind is a pair of old tires and a tube of tubular glue, all squeezed out"
Sugar "Kane" Kowalczyk
#11
Bike Butcher of Portland
Join Date: Jul 2014
Location: Portland, OR
Posts: 11,634
Bikes: It's complicated.
Mentioned: 1299 Post(s)
Tagged: 0 Thread(s)
Quoted: 4678 Post(s)
Liked 5,795 Times
in
2,281 Posts
In a perfect world I'd want a nice catalyzed wet paint job on all my bikes, but you're talking something like 3x the cost. There are enough good powder coaters that know how to do bikes properly nowadays that unless you pick a crappy one, you'll probably be just fine.
__________________
If someone tells you that you have enough bicycles and you don't need any more, stop talking to them. You don't need that kind of negativity in your life.
If someone tells you that you have enough bicycles and you don't need any more, stop talking to them. You don't need that kind of negativity in your life.
Likes For gugie:
#12
Bike Butcher of Portland
Join Date: Jul 2014
Location: Portland, OR
Posts: 11,634
Bikes: It's complicated.
Mentioned: 1299 Post(s)
Tagged: 0 Thread(s)
Quoted: 4678 Post(s)
Liked 5,795 Times
in
2,281 Posts
Back to the OP, I know of 2 powder coaters that can send a frame out for chemical strip. I think cost was around $40
__________________
If someone tells you that you have enough bicycles and you don't need any more, stop talking to them. You don't need that kind of negativity in your life.
If someone tells you that you have enough bicycles and you don't need any more, stop talking to them. You don't need that kind of negativity in your life.
Likes For gugie:
#13
Senior Member
Join Date: Oct 2013
Location: Great White North
Posts: 926
Bikes: I have a few
Mentioned: 6 Post(s)
Tagged: 0 Thread(s)
Quoted: 340 Post(s)
Liked 210 Times
in
104 Posts
I've heard this arguement before, and it doesn't make much sense to me. Who doesn't want a lifetime paint job? I don't know many people who plan to repaint. Perhaps somebody somewhere wants to repaint every few years as a fashion statement.
In a perfect world I'd want a nice catalyzed wet paint job on all my bikes, but you're talking something like 3x the cost. There are enough good powder coaters that know how to do bikes properly nowadays that unless you pick a crappy one, you'll probably be just fine.
In a perfect world I'd want a nice catalyzed wet paint job on all my bikes, but you're talking something like 3x the cost. There are enough good powder coaters that know how to do bikes properly nowadays that unless you pick a crappy one, you'll probably be just fine.
Wileyone it can be softened up with a blow torch and scraped off just don't go mental and over heat the pipe.
#14
Senior Member
Thread Starter
Join Date: Oct 2014
Location: GWN
Posts: 2,538
Mentioned: 27 Post(s)
Tagged: 0 Thread(s)
Quoted: 1858 Post(s)
Liked 606 Times
in
403 Posts
Back to the OP, I know of 2 powder coaters that can send a frame out for chemical strip. I think cost was around $40
#15
Bike Butcher of Portland
Join Date: Jul 2014
Location: Portland, OR
Posts: 11,634
Bikes: It's complicated.
Mentioned: 1299 Post(s)
Tagged: 0 Thread(s)
Quoted: 4678 Post(s)
Liked 5,795 Times
in
2,281 Posts
Good point, sometimes I forget that we're in strange times.
__________________
If someone tells you that you have enough bicycles and you don't need any more, stop talking to them. You don't need that kind of negativity in your life.
If someone tells you that you have enough bicycles and you don't need any more, stop talking to them. You don't need that kind of negativity in your life.
#16
Senior Member
Join Date: Apr 2007
Location: Thunder Bay, Ontario, Canada - burrrrr!
Posts: 11,674
Bikes: 1958 Rabeneick 120D, 1968 Legnano Gran Premio, 196? Torpado Professional, 2000 Marinoni Piuma
Mentioned: 210 Post(s)
Tagged: 0 Thread(s)
Quoted: 1372 Post(s)
Likes: 0
Liked 1,751 Times
in
938 Posts
Never really liked the idea of powder coated bikes, even though I had a drop dead gorgeous orange Marinoni that was done with pc. That said, have a look at this page. It might be a help.
__________________
"98% of the bikes I buy are projects".
"98% of the bikes I buy are projects".
#17
I never finish anyth
Join Date: Jul 2010
Location: Western KY
Posts: 1,114
Bikes: 2008 Merckx LXM, 2003 Giant XTC mtb, 2001 Lemond Alpe d'Huez, 1997 Lemond Zurich, 1989 Cannondale ST, 1988 Masi Nuovo Strada, 1983 Pinarello Turismo
Mentioned: 63 Post(s)
Tagged: 0 Thread(s)
Quoted: 294 Post(s)
Liked 137 Times
in
86 Posts
I removed powder coating from a steel frame, the only chemical I tried that worked was "aircraft stripper". No other remover even made a dent. It's fairly nasty stuff, and you will definitely want to use gloves and eye protection.
I bought it at ace hardware, and it was a gel so it would work on the round tube shapes. You put it on, and then wait. Add another coat and wait some more. Then you should be able to scrape it off. Once most of it is scraped off you can use a scotchbrite pad to get the nooks and crannies around lugs and where tubes are joined.
Having done it before, I don't envy you this task.
I bought it at ace hardware, and it was a gel so it would work on the round tube shapes. You put it on, and then wait. Add another coat and wait some more. Then you should be able to scrape it off. Once most of it is scraped off you can use a scotchbrite pad to get the nooks and crannies around lugs and where tubes are joined.
Having done it before, I don't envy you this task.
__________________
Dale, NL4T
Dale, NL4T
#18
Senior Member
Thread Starter
Join Date: Oct 2014
Location: GWN
Posts: 2,538
Mentioned: 27 Post(s)
Tagged: 0 Thread(s)
Quoted: 1858 Post(s)
Liked 606 Times
in
403 Posts
I removed powder coating from a steel frame, the only chemical I tried that worked was "aircraft stripper". No other remover even made a dent. It's fairly nasty stuff, and you will definitely want to use gloves and eye protection.
I bought it at ace hardware, and it was a gel so it would work on the round tube shapes. You put it on, and then wait. Add another coat and wait some more. Then you should be able to scrape it off. Once most of it is scraped off you can use a scotchbrite pad to get the nooks and crannies around lugs and where tubes are joined.
Having done it before, I don't envy you this task.
I bought it at ace hardware, and it was a gel so it would work on the round tube shapes. You put it on, and then wait. Add another coat and wait some more. Then you should be able to scrape it off. Once most of it is scraped off you can use a scotchbrite pad to get the nooks and crannies around lugs and where tubes are joined.
Having done it before, I don't envy you this task.
#19
I never finish anyth
Join Date: Jul 2010
Location: Western KY
Posts: 1,114
Bikes: 2008 Merckx LXM, 2003 Giant XTC mtb, 2001 Lemond Alpe d'Huez, 1997 Lemond Zurich, 1989 Cannondale ST, 1988 Masi Nuovo Strada, 1983 Pinarello Turismo
Mentioned: 63 Post(s)
Tagged: 0 Thread(s)
Quoted: 294 Post(s)
Liked 137 Times
in
86 Posts
#22
Senior Member
IIRC, "aircraft stripper is methyene chloride based.. toxic, corrosive to skin, carcinogen, etc. may not be available where you live depending on the regulations. It is gel based and works well (looking like that orange frame pictured)