Leaky Valve: Replace?
10-14-18, 08:57 PM
#1
Senior Member
Thread Starter
Leaky Valve: Replace?
I found the source of the slow leak in my front Tre. The tube itself is fine but the valve leaks air unless it's screwed in very tightly. Tightened up the valve and everything seems to be in working order. Should I replace it anyway? This is the first time I've encountered this type of problem so I guess I've been lucky.
Anyone else dealt with this problem?
Anyone else dealt with this problem?
10-14-18, 09:07 PM
#2
Old fart
Join Date: Nov 2004
Location: Appleton WI
Posts: 24,777
Bikes: Several, mostly not name brands.
Mentioned: 153 Post(s)
Tagged: 0 Thread(s)
Quoted: 3582 Post(s)
Liked 3,395 Times
in
1,929 Posts
Is this a replaceable core? If so, try a different valve core.
10-14-18, 09:49 PM
#3
Senior Member
Thread Starter
10-14-18, 11:57 PM
#5
Senior Member
Yea, replace it
peace of mind & time saver not
having to pump up a slow leak.
Good practice in case it ever needs
done when out & about
peace of mind & time saver not
having to pump up a slow leak.
Good practice in case it ever needs
done when out & about
10-15-18, 03:48 AM
#6
Senior Member
You didn't say if it is a Schrader valve (like on a car) or Presta (the skinnier ones). Schrader valves are removable (with a cheap tool) and cost about $.50 each - good deal cheaper than a new tube.
Some Presta valves are replaceable, not all, and they cost about $1.50 each - starting to get closer to the price of a new tube.
Personally, if I have a valve leaking I just replace the entire tube. It always seems like the new valve stops the leak but not long after I get a leak around the base of the rubber where the valve stem goes into the tube.
Some Presta valves are replaceable, not all, and they cost about $1.50 each - starting to get closer to the price of a new tube.
Personally, if I have a valve leaking I just replace the entire tube. It always seems like the new valve stops the leak but not long after I get a leak around the base of the rubber where the valve stem goes into the tube.
10-15-18, 07:44 AM
#7
Senior Member
Join Date: Jan 2010
Posts: 39,214
Mentioned: 211 Post(s)
Tagged: 1 Thread(s)
Quoted: 18397 Post(s)
Liked 15,493 Times
in
7,316 Posts
I was born with a leaky valve. Had to have it replaced when I was 25. Cost a lot more than a new tube.
10-15-18, 07:52 AM
#8
Senior Member
Join Date: Jan 2016
Location: 961' 42.28° N, 83.78° W (A2)
Posts: 2,344
Bikes: Mongoose Selous, Trek DS
Mentioned: 8 Post(s)
Tagged: 0 Thread(s)
Quoted: 941 Post(s)
Liked 319 Times
in
189 Posts
If you are not now, start using valve caps. I know this amounts to heresy on this forum, but.. 
10-15-18, 02:17 PM
#10
Senior Member
Thread Starter
You didn't say if it is a Schrader valve (like on a car) or Presta (the skinnier ones). Schrader valves are removable (with a cheap tool) and cost about $.50 each - good deal cheaper than a new tube.
Some Presta valves are replaceable, not all, and they cost about $1.50 each - starting to get closer to the price of a new tube.
Personally, if I have a valve leaking I just replace the entire tube. It always seems like the new valve stops the leak but not long after I get a leak around the base of the rubber where the valve stem goes into the tube.
Some Presta valves are replaceable, not all, and they cost about $1.50 each - starting to get closer to the price of a new tube.
Personally, if I have a valve leaking I just replace the entire tube. It always seems like the new valve stops the leak but not long after I get a leak around the base of the rubber where the valve stem goes into the tube.
I always use valve caps. I think they're a good idea.
10-15-18, 02:37 PM
#11
Senior Member
Join Date: Nov 2014
Location: Eugene, Oregon, USA
Posts: 27,547
Mentioned: 217 Post(s)
Tagged: 0 Thread(s)
Quoted: 18350 Post(s)
Liked 4,502 Times
in
3,346 Posts
Some presta valve cores are replaceable... some are not.
Look for two flats on the threads just below the top. I'm pretty sure that if you have a replaceable core, then they are pretty universal.
With more, better sealants, hopefully we'll see replaceable cores becoming more common.\
There are special tools to remove them, but I just use a standard adjustable wrench.
Look for two flats on the threads just below the top. I'm pretty sure that if you have a replaceable core, then they are pretty universal.
With more, better sealants, hopefully we'll see replaceable cores becoming more common.\
There are special tools to remove them, but I just use a standard adjustable wrench.
10-15-18, 02:40 PM
#12
Lopsided biped
Join Date: Nov 2017
Location: NE Ohio
Posts: 737
Bikes: 2017 Day 6 Cyclone (the Buick); 2015 Simcoe Deluxe (the Xebec); Street Strider 3i (the not-a-bike); GreenSpeed Anura (the Black Swan)
Mentioned: 3 Post(s)
Tagged: 0 Thread(s)
Quoted: 316 Post(s)
Liked 160 Times
in
97 Posts
I use the valve caps that have the little (Schrader) valve remover tool built into them. I think I've only used those once in my whole life, but it's nice to have right there if you need it. Get them at any auto parts store.
10-15-18, 02:47 PM
#13
Senior Member
Join Date: Jan 2013
Posts: 1,388
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 176 Post(s)
Liked 25 Times
in
13 Posts
Some presta valve cores are replaceable... some are not.
Look for two flats on the threads just below the top. I'm pretty sure that if you have a replaceable core, then they are pretty universal.
With more, better sealants, hopefully we'll see replaceable cores becoming more common.\
There are special tools to remove them, but I just use a standard adjustable wrench.
Look for two flats on the threads just below the top. I'm pretty sure that if you have a replaceable core, then they are pretty universal.
With more, better sealants, hopefully we'll see replaceable cores becoming more common.\
There are special tools to remove them, but I just use a standard adjustable wrench.
10-15-18, 03:00 PM
#15
Senior Member
Join Date: Feb 2017
Location: Hollister, CA (not the surf town)
Posts: 1,734
Bikes: 2019 Specialized Roubaix Comp Di2, 2009 Roubaix, early 90's Giant Iguana
Mentioned: 8 Post(s)
Tagged: 0 Thread(s)
Quoted: 641 Post(s)
Liked 1,517 Times
in
549 Posts
I found the source of the slow leak in my front Tre. The tube itself is fine but the valve leaks air unless it's screwed in very tightly. Tightened up the valve and everything seems to be in working order. Should I replace it anyway? This is the first time I've encountered this type of problem so I guess I've been lucky.
Anyone else dealt with this problem?
Anyone else dealt with this problem?
10-15-18, 03:23 PM
#16
Old fart
Join Date: Nov 2004
Location: Appleton WI
Posts: 24,777
Bikes: Several, mostly not name brands.
Mentioned: 153 Post(s)
Tagged: 0 Thread(s)
Quoted: 3582 Post(s)
Liked 3,395 Times
in
1,929 Posts
If you use sealant in your tubes, a removable core makes it easier to inject the sealant, and if/when the sealant clogs the valve, you simply remove it and soak in ammonia to dissolve the sealant. I find it handy to have a few core available, so I can swap a clean one in while letting the clogged one soak. You can buy cores separately or in bulk, or even salvage them for free from discarded tubes.
10-15-18, 03:37 PM
#17
Senior Member
Join Date: Nov 2014
Location: Eugene, Oregon, USA
Posts: 27,547
Mentioned: 217 Post(s)
Tagged: 0 Thread(s)
Quoted: 18350 Post(s)
Liked 4,502 Times
in
3,346 Posts
Attach to the two flats. Turn counter clockwise. Be careful of the spokes.
A turn or two, and you can usually get it the rest of the way out/in with the fingers.
Note, this is for PRESTA as above.
For Schrader, you'll need the tool, or a valve cap with the tool.
A turn or two, and you can usually get it the rest of the way out/in with the fingers.
Note, this is for PRESTA as above.
For Schrader, you'll need the tool, or a valve cap with the tool.
