RestoMod help
#1
Junior Member
Thread Starter
Join Date: Apr 2020
Location: Tulsa, OK
Posts: 112
Bikes: '14 Leader Renovatio, '96 Trek 1400, '88 Fisher Montare XT
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 49 Post(s)
Liked 69 Times
in
34 Posts
RestoMod help
Is it possible to turn an old(80s) rigid mtb with 130mm rear spacing into a 1xWhatever without cold setting? Any parts suggestions? Tips and/or tricks? Haven't stumbled across a thread discussing this type of thing, so maybe this will help some adventurous tinkerers. Figured, before one starts down the rabbit hole, BF is the resource. I'm looking for a non-disc, 130mm bolt on 9-11 speed rear hub.
#2
I’m a little Surly
Join Date: Jan 2010
Location: Near the district
Posts: 2,423
Bikes: Two Cross Checks, a Karate Monkey, a Disc Trucker, and a VO Randonneur
Mentioned: 5 Post(s)
Tagged: 0 Thread(s)
Quoted: 699 Post(s)
Liked 1,297 Times
in
648 Posts
1/xx
Put wheel in bike with casette you want
Remove unwanted chainrings
Remove unwanted derailleur
Remove unwanted shifter
Use chain appropriate for cassette
??Profit
135 will fit in 130 frame with a bit of muscle, new wide narrow chainring or keeper if you drop chains.
Put wheel in bike with casette you want
Remove unwanted chainrings
Remove unwanted derailleur
Remove unwanted shifter
Use chain appropriate for cassette
??Profit
135 will fit in 130 frame with a bit of muscle, new wide narrow chainring or keeper if you drop chains.
#3
Junior Member
Thread Starter
Join Date: Apr 2020
Location: Tulsa, OK
Posts: 112
Bikes: '14 Leader Renovatio, '96 Trek 1400, '88 Fisher Montare XT
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 49 Post(s)
Liked 69 Times
in
34 Posts
Thanks Germany_chris
I forgot to mention that the current hub I'm working with has a 7-speed freewheel attached. It is an old 3x7 that I'm running 1x7 for now with a narrow-wide chainring up front. FD and shifter are currently at peace in the parts bin. Wish it were easy as swapping a cassette.
I forgot to mention that the current hub I'm working with has a 7-speed freewheel attached. It is an old 3x7 that I'm running 1x7 for now with a narrow-wide chainring up front. FD and shifter are currently at peace in the parts bin. Wish it were easy as swapping a cassette.
#4
Senior Member
Join Date: Dec 2014
Location: Central Virginia
Posts: 4,790
Bikes: Numerous
Mentioned: 150 Post(s)
Tagged: 0 Thread(s)
Quoted: 1678 Post(s)
Liked 3,124 Times
in
921 Posts
Assuming steel frame, I’d just squeeze the 135 hub in there. I’ve used 130 mm spaced rear hubs on 126 mm rear spaced frames without cold setting, although a few people frown upon this. I’ve been riding my Merckx Century a few years this way. You can also consider just using a 130 mm road hub.
__________________
N = '96 Colnago C40, '04 Wilier Alpe D'Huez, '10 Colnago EPS, '85 Merckx Pro, '89 Merckx Century, '86 Tommasini Professional, '04 Teschner Aero FX Pro, '05 Alan Carbon Cross, '86 De Rosa Professional, '82 Colnago Super, '95 Gios Compact Pro, '95 Carrera Zeus, '84 Basso Gap, ‘89 Cinelli Supercorsa, ‘83 Bianchi Specialissima, ‘VO Randonneur, Ritchey Breakaway Steel, '84 Paletti Super Prestige, Heron Randonneur
N = '96 Colnago C40, '04 Wilier Alpe D'Huez, '10 Colnago EPS, '85 Merckx Pro, '89 Merckx Century, '86 Tommasini Professional, '04 Teschner Aero FX Pro, '05 Alan Carbon Cross, '86 De Rosa Professional, '82 Colnago Super, '95 Gios Compact Pro, '95 Carrera Zeus, '84 Basso Gap, ‘89 Cinelli Supercorsa, ‘83 Bianchi Specialissima, ‘VO Randonneur, Ritchey Breakaway Steel, '84 Paletti Super Prestige, Heron Randonneur
Likes For Spaghetti Legs:
#5
Full Member
Join Date: Dec 2012
Location: North Seattle
Posts: 387
Bikes: Davidson ’81
Mentioned: 2 Post(s)
Tagged: 0 Thread(s)
Quoted: 120 Post(s)
Liked 229 Times
in
121 Posts
A couple of thoughts -
If you choose to use a 135 hub without cold setting (and realigning the dropouts afterwards) the dropout faces will be slightly misaligned and engagement of the QRs and locknuts will suffer as a result. With horizontal dropouts, the wheel can slip forward under load. This happened to me on my ‘87 High Sierra, which was spaced 130 from the factory for a 6 speed hub, but came to me with a cheap 135 replacement wheel. I was standing and grinding uphill when it happened. The bike came to a dead stop, and the wheel went up into my fender and bent it a little. Fortunately I was able to dismount without incident, but it could have been messy. I am over 200 pounds which didn’t help any.
That said, it will be much easier to find a 135 26” wheel with the freehub you want, unless you’re going to lace the wheel yourself. Many 135 spaced wheels can be respaced to 130 by shortening or replacing the axle and losing some spacers. The rim will have to be re-dished if you go this route.
If you choose to use a 135 hub without cold setting (and realigning the dropouts afterwards) the dropout faces will be slightly misaligned and engagement of the QRs and locknuts will suffer as a result. With horizontal dropouts, the wheel can slip forward under load. This happened to me on my ‘87 High Sierra, which was spaced 130 from the factory for a 6 speed hub, but came to me with a cheap 135 replacement wheel. I was standing and grinding uphill when it happened. The bike came to a dead stop, and the wheel went up into my fender and bent it a little. Fortunately I was able to dismount without incident, but it could have been messy. I am over 200 pounds which didn’t help any.
That said, it will be much easier to find a 135 26” wheel with the freehub you want, unless you’re going to lace the wheel yourself. Many 135 spaced wheels can be respaced to 130 by shortening or replacing the axle and losing some spacers. The rim will have to be re-dished if you go this route.
#6
Senior Member
Join Date: Jun 2019
Location: Portland Oregon
Posts: 996
Mentioned: 7 Post(s)
Tagged: 0 Thread(s)
Quoted: 457 Post(s)
Liked 462 Times
in
270 Posts
Cold setting the frame is pretty straight forward, you should use clamps to hold the stays onto the brake and chains stay bridges when you bend the rear triangle wider so the force of bending the stays isn't taken by the welds/brazing.
https://www.sheldonbrown.com/frame-spacing.html
https://www.sheldonbrown.com/frame-spacing.html
#7
Senior Member
Join Date: Mar 2015
Location: New Zealand
Posts: 1,053
Bikes: Gunnar, Shogun, Concorde, F Moser, Pete Tansley, Rocky Mtn, Diamant, Krapf, Marin, Avanti, Winora, Emmelle, Ken Evans
Mentioned: 5 Post(s)
Tagged: 0 Thread(s)
Quoted: 275 Post(s)
Liked 417 Times
in
218 Posts
lace a 26" rim to a new shimano road hub.
#8
Senior Member
Join Date: Jan 2008
Location: Beaverton, OR
Posts: 14,752
Bikes: Yes
Mentioned: 525 Post(s)
Tagged: 0 Thread(s)
Quoted: 3236 Post(s)
Liked 3,883 Times
in
1,443 Posts
If the 7-speed hub is Shimano, you may be able to just swap the freehub body. I've done this and it was pretty easy, though it may have involved a slight redishing of the wheel.
Otherwise, I'd build/have built a wheel with a road hub as others have suggested. Shimano road hubs are dirt cheap and extremely reliable.
Otherwise, I'd build/have built a wheel with a road hub as others have suggested. Shimano road hubs are dirt cheap and extremely reliable.
__________________
My Bikes
My Bikes