Bike Forums

Bike Forums (https://www.bikeforums.net/forum.php)
-   Track Cycling: Velodrome Racing and Training Area (https://www.bikeforums.net/forumdisplay.php?f=210)
-   -   Stem ?? (https://www.bikeforums.net/showthread.php?t=1187667)

brooklyn6640 11-09-19 05:46 PM

Stem ??
 
What stem and bar model do you have on your track bikes? thank,s

Huskey 11-09-19 06:19 PM

Carbon Pro vibe sprint 105mm

carleton 11-10-19 02:50 PM


Originally Posted by brooklyn6640 (Post 21201990)
What stem and bar model do you have on your track bikes? thank,s

What’s up with your punctuation? Are you using a non-standard keyboard or is this just your thing?

2500W 03-16-20 04:17 AM


Originally Posted by brooklyn6640 (Post 21201990)
What stem and bar model do you have on your track bikes? thank,s

Well, currently it is the only weak point of my track bike. Initially, that were the cheap spokes and rear tubular tyre used without sealant until I solved all that successfully.

My bike is steel Tommasini, 1" fork, i.e. it may accept a 22.2 quill only. I dislike aluminium Italian quill stems of 1980s. So I renewed the bike three years ago by usung M-Wave quill adaptor and a standard 28.6 stem. Two years later I broke up the quill adaptor while rode on the street. Then I bought a Nitto NT quill stem 110mm that appeared too flexible. Currently, I use an old AL quill stem, thick, 140mm.

So now I consider either buying Nitto NJ Pro Steel Stem or ordering a custom steel quill adaptor to a local craftsman. However, I am very puzzled of Nittos weight specifications. NJ 140mm, 58-degree is listed 475g, while its 65-degree counterpart I prefer is 375g only. Is this a mistake or the latter is truly lighter and softer?

700wheel 03-16-20 11:22 AM


Originally Posted by 2500W (Post 21369254)
Well, currently it is the only weak point of my track bike. Initially, that were the cheap spokes and rear tubular tyre used without sealant until I solved all that successfully.

My bike is steel Tommasini, 1" fork, i.e. it may accept a 22.2 quill only. I dislike aluminium Italian quill stems of 1980s. So I renewed the bike three years ago by usung M-Wave quill adaptor and a standard 28.6 stem. Two years later I broke up the quill adaptor while rode on the street. Then I bought a Nitto NT quill stem 110mm that appeared too flexible. Currently, I use an old AL quill stem, thick, 140mm.

So now I consider either buying Nitto NJ Pro Steel Stem or ordering a custom steel quill adaptor to a local craftsman. However, I am very puzzled of Nittos weight specifications. NJ 140mm, 58-degree is listed 475g, while its 65-degree counterpart I prefer is 375g only. Is this a mistake or the latter is truly lighter and softer?

Have you considered converting your bike to eliminate the quill adaptor? There are several videos on YouTube. Search for "convert a quill bike stem to threadless". This may be more complicated for a track bike unless you go with a steel fork.

Incidentally I used a Technomic quill stem on my old track bike (now used on my basement trainer) for years with no problem.

2500W 03-17-20 07:09 AM

Thank you 700wheel, I just now became aware of the availability of 1 inch threadless headsets. Recently, I even considered the possibility of replacing current threaded steerer with a longer threaded one so to screw up the Campagnolo cone and then somewhat mount a standard stem above it.

brawlo 03-17-20 04:20 PM

3T ARX stems (I have a collection of the older 4 bolt ones) and BT bars

topflightpro 03-18-20 06:22 AM

I am a big fan of Thomson X4 stems. They are technically mountain bike stems, but that is fine. According to the Fairwheel Bikes test, they are the third stiffest stem tested, after the Pro Vibe Sprint and Zipp SL, but at a fraction of the cost.

Stem Review - Fairwheel Bikes Blog


All times are GMT -6. The time now is 09:19 PM.


Copyright © 2024 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.