Ultegra RD-RX800-GS is what you are looking for + a wolftooth road link and you should be ok to use 9000 cranks and a 11-40 cassette. Ultegra R8000 levers should work with RD-RX800-GS.
|
Originally Posted by Schlafen
(Post 22724735)
Ultegra RD-RX800-GS is what you are looking for + a wolftooth road link and you should be ok to use 9000 cranks and a 11-40 cassette. Ultegra R8000 levers should work with RD-RX800-GS.
|
Originally Posted by Hondo6
(Post 22724813)
An earlier post by the OP indicates he's not in the US and that Wolftooth products aren't readily available in his locale. So while that solution is almost certainly workable, it doesn't work for the OP's particular situation.
|
Originally Posted by Schlafen
(Post 22724819)
i would try a 40t cassette without a road link first. If he needs one, derailleur hanger extenders are available everywhere in the world for about a 5'er. eBay, amazon, etc.
Might be worth a try - with his existing FD first without, then with the derailleur hanger if necessary. But the OP would have to find and buy a 9-speed 40T cassette to try it with his existing FD, and he could end up stuck with something he can't use. Ditto with an 11 speed RD and shifters. Dunno. OP's bike, so that's his call. |
Originally Posted by Hondo6
(Post 22724832)
A generic derailleur hanger extender could well work with his existing RD, and might be available in the OP's area. It would also very likely work with the upgraded RD and shifters you suggest.
Might be worth a try - with his existing FD first without, then with the derailleur hanger if necessary. But the OP would have to find and buy a 9-speed 40T cassette to try it with his existing FD, and he could end up stuck with something he can't use. Ditto with an 11 speed RD and shifters. Dunno. OP's bike, so that's his call. For the RX800 to work with his DA9000 he needs at least 105 R7000 shifters and a FD9000. If he goes for 50/34 rings and a 11/36 cassette, for which the derailleur is rated as standard, he'll have enough range where he will not need to run a 40t, even though the RX800 derailleur will most likely work with a 40t cassette without needing the extender. 40t is usually used with 1x for range but OP wants a 2x so 40t will be overkill and with a 36/34 ratio he could climb up a wall anyway. It depends if current bike and derailleur hanger, if it's a steel bike with an integrated hanger it should work no problem as they have longer hangers than the removable type. |
Originally Posted by jeff3069
(Post 22722440)
Hello all!:)
Have not been here for quite awhile I would like to (buy and) install a new 11 spd group on an old cyclocross bike (of 9 speeds). 1. The current setup of 50/34 and 11-34 works alright for me. 2. in the new build, I prefer to use a 50/34 Dura Ace 9000 11spd crank that I have. 3. I am told that a long cage XT RD (have a long XTR one now) is not going to work with 105 sifters, and was advised to get a GRX group My question is, please, what 11spd shifters, derailleurs should I buy so that they will work well with the above crank? I'd be happy to have a cassette with even bigger cogs (36..40) Thanks!! J Would be surprised if it doesn't work. Though, I'd rather sell the overpriced Dura Ace crank and stay with the 2x9 setup. |
Originally Posted by Bike Gremlin
(Post 22725002)
.
|
Originally Posted by Schlafen
(Post 22725006)
So, you're the guy with the youtube channel with the same name.
|
Originally Posted by jeff3069
(Post 22724313)
Hi base2,
The XTR RD currently on the bike was used (not new) when I got this bike in Jan 2006 - it is 16-20 years old with not a single problem I prefer to stick with shimano especially considering that I am not in the US and this Woiftooth product is unknown here, not to mention parts if needed |
Originally Posted by Schlafen
(Post 22724998)
If he's moving to 11s it will not work with a 9s XTR, different pull. A 9s 40t cassette may be available but that's not what he's asking here.
For the RX800 to work with his DA9000 he needs at least 105 R7000 shifters and a FD9000. If he goes for 50/34 rings and a 11/36 cassette, for which the derailleur is rated as standard, he'll have enough range where he will not need to run a 40t, even though the RX800 derailleur will most likely work with a 40t cassette without needing the extender. 40t is usually used with 1x for range but OP wants a 2x so 40t will be overkill and with a 36/34 ratio he could climb up a wall anyway. It depends if current bike and derailleur hanger, if it's a steel bike with an integrated hanger it should work no problem as they have longer hangers than the removable type. Above, I didn't think I needed to say that "with his existing RD" included the use of his existing 9 speed rear shifter as I thought that would be both obvious and understood - particularly since I also indicated he'd need to get a 9-speed, 40T cassette. I was merely pointing out that if going to a larger (e.g., 40T) max rear sprocket was the OPs primary goal that there might be a way to do that without the expense of new RD/FD/shifters. |
Guys, Thanks for the help! Considering the above I may just get a Shimano Sora FC-R3000 Crankset - 175mm, 9-Speed, 50/34t (current chinrings are ~finished) + new chain and cassttee - end of story:) 9 or 11 doesn't meeter much to me on this bike
1 question please - the RD in the below photos - what largest cog it can handle ? 36 ? maybe 40? (it currently works with 11-34) Thanks a lot. https://cimg2.ibsrv.net/gimg/bikefor...68fc1a52d5.jpg https://cimg3.ibsrv.net/gimg/bikefor...06dd9a2240.jpg https://cimg4.ibsrv.net/gimg/bikefor...006b43bb83.jpg |
Originally Posted by jeff3069
(Post 22725082)
Guys, Thanks for the help! Considering the above I may just get a Shimano Sora FC-R3000 Crankset - 175mm, 9-Speed, 50/34t (current chinrings are ~finished) + new chain and cassttee - end of story:) 9 or 11 doesn't meeter much to me on this bike
1 question please - the RD in the below photos - what largest cog it can handle ? 36 ? maybe 40? (it currently works with 11-34) Thanks a lot. https://cimg2.ibsrv.net/gimg/bikefor...68fc1a52d5.jpg https://cimg3.ibsrv.net/gimg/bikefor...06dd9a2240.jpg https://cimg4.ibsrv.net/gimg/bikefor...006b43bb83.jpg The 9-speed Shimano XTR RDs appear to have been from the late 1990s/early 2000s, and appear to have had 950 or 960-series model numbers (e.g., "RD-M95X" or "RD-M96X", where X is another number. The oldest Shimano specification compilation listed in Shimano's specifications repository is from 2004-2005. Several models of the M96X and M95X are listed there. Shimano indicates a 34T max rear sprocket or all of the 9-speed XTR RDs listed there. However, Shimano's noted for being fairly conservative in their specifications. A 36T may work "out of the box" without a RD hanger extender - or it may not. And that may have simply been the largest rear cassette sprocket they were selling at the time. RD hanger extenders are fairly inexpensive, and may well allow a 40T or larger largest rear sprocket. I understand shifting smoothness/responsiveness may suffer a bit with a hanger extender, but I've never tried one personally so I can't verify that. Hope this helps. With a specific model number (it will be embossed on the RD somewhere, likely on the inside of one of the cage plates), I might be able to be definitive on what Shimano says. |
Thank you very much Hondo6.
If you could please show me a link to buying this extender, that will be Nice:) May either get it or may buy a new RD that supports ~40 |
Originally Posted by jeff3069
(Post 22725245)
Thank you very much Hondo6.
If you could please show me a link to buying this extender, that will be Nice:) May either get it or may buy a new RD that supports ~40 https://www.amazon.com/derailleur-ex...KDNoIE9f8wGJ8I I'd recommend you get the type that extends your existing RD hanger vice replaces it completely. Replacing an existing hanger with a longer one only works if (1) you have a replaceable hanger (on some frames, they're part of the frame itself) and (2) you can find one that's an exact match for your existing hanger's mounting scheme (they're NOT universally mounted the same way). |
Thank you Hondo 6!
|
Originally Posted by jeff3069
(Post 22725245)
Thank you very much Hondo6.
If you could please show me a link to buying this extender, that will be Nice:) May either get it or may buy a new RD that supports ~40 |
That is right too.. Thank you!
|
Guys, thanks to your knowledgeable advice, the bike is up and running with a new 9s crank, 36T cassette, chain, break pads.. :) Thank you ! :)
https://cimg9.ibsrv.net/gimg/bikefor...5f96f24187.png |
Glad to see you got everything working. For when you eventually need to replace the RD pulleys: Shimano XTR M970 9-Speed Rear Derailleur Pulley Set: Version 2 - Modern Bike
|
Originally Posted by SoSmellyAir
(Post 22734925)
Glad to see you got everything working. For when you eventually need to replace the RD pulleys: Shimano XTR M970 9-Speed Rear Derailleur Pulley Set: Version 2 - Modern Bike
Yesterday when my friend at the bike shop installed the parts, we had a new RD ready too, but when he saw that this veteran xtr works well with the 36T we thought we'll leave it on. |
Hi, Can you please look at the enclosed photo? that's a SCHWALBE Marathon Plus 35mm. Do you think this clearance will safely allow a 40mm tire? Thanks!
https://cimg1.ibsrv.net/gimg/bikefor...fb6919b376.jpg |
All times are GMT -6. The time now is 09:56 PM. |
Copyright © 2024 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.