Went out this a.m. with the intention of doing a 50-60 mile ride with the group. The heat and humidity were overwhelming and I ended up splitting off and doing 30-ish with two fast guys with hangovers and someone else who was feeling the conditions too. As soon as I wasn’t oppressed by the prospect of a death march in 76% dew point, I perked up and concentrated my meager resources on making those hangovers worse.
|
Originally Posted by LesterOfPuppets
(Post 22145979)
They prevent me from caring about it, so yeah, I'll leave em dirty like that. But with discs I don't bother since there's none of that gritty rim grinding sound when braking :)
|
I drove 30 minutes to meet up with 14 riders in the avocado growing area north of here. There was a short loop but 10 of us opted for the longer 68 mile ride. It wasn't too hot and I had a great time. Here, I'm second from left.
https://scontent-lax3-2.xx.fbcdn.net...f8&oe=60F8917B A few low clouds early. https://scontent-lax3-2.xx.fbcdn.net...cc&oe=60F8256B |
There was one 3 mile climb carved into this hill.
https://scontent-lax3-2.xx.fbcdn.net...80&oe=60F87123 Miles of farmland. https://scontent-lax3-1.xx.fbcdn.net...16&oe=60F8DE33 And miles of quiet back roads. https://scontent-lax3-2.xx.fbcdn.net...50&oe=60F8AFCB Some pretty flowers, too. https://scontent-lax3-2.xx.fbcdn.net...cb&oe=60F92FAC |
Originally Posted by big john
(Post 22146010)
I drove 30 minutes to meet up with 14 riders in the avocado growing area north of here.
|
Originally Posted by ls01
(Post 22145848)
64 miles on the disk bike. I think I finally figured out my discontent with that bike. The brake levers/hoods aren't even. The right side is higher than the left. Not a lot but enough that after a few seconds on the hoods I'm fighting with the bars. Probably pull it apart tonight, fix it and rewrap the bars.
|
Originally Posted by Velo Vol
(Post 22146039)
Did you pick one?
Today this guy had the noisiest rear hub I've heard and he kept getting on my wheel. I don't blame him, if I could draft a guy a foot taller than I am I would probably do it. Anyway when we stopped I asked if that was one of those new L.O.U.D. hubs. It took a minute but he finally laughed. |
Originally Posted by LesterOfPuppets
(Post 22145877)
Currently watching the Rocket City Trash Pandas game
https://cimg6.ibsrv.net/gimg/bikefor...f3dd1d6202.png |
Originally Posted by big john
(Post 22146045)
No.
Originally Posted by DougRNS
(Post 22146070)
I think the whole weekend is free check it out tomorrow.!
|
|
Got the bolt out. I think big john said it would twist with my fingers and he was right.
The pinch bolts on the crank didn’t feel all that tight. On the arm it states they should be at 12nm-14nm. I am not an expert but it didn’t take any effort for me to loosen them at all. I hope that’s the issue. Trying to get the arm off as we speak. I have a rubber mallet and I am tapping the arm. It has moved a little bit but not enough for me to remove it yet. |
Originally Posted by DougRNS
(Post 22146070)
All games free today on MLB.TV. I think the whole weekend is free check it out tomorrow.!
|
Originally Posted by Velo Vol
(Post 22146117)
No.
|
Originally Posted by LAJ
(Post 22146126)
No Baseball. I'll be here tomorrow.
|
Originally Posted by bampilot06
(Post 22146144)
Got the bolt out. I think big john said it would twist with my fingers and he was right.
The pinch bolts on the crank didn’t feel all that tight. On the arm it states they should be at 12nm-14nm. I am not an expert but it didn’t take any effort for me to loosen them at all. I hope that’s the issue. Trying to get the arm off as we speak. I have a rubber mallet and I am tapping the arm. It has moved a little bit but not enough for me to remove it yet. |
Originally Posted by Velo Vol
(Post 22146150)
Bandimere Speedway?
|
Originally Posted by bampilot06
(Post 22146144)
Got the bolt out. I think big john said it would twist with my fingers and he was right.
The pinch bolts on the crank didn’t feel all that tight. On the arm it states they should be at 12nm-14nm. I am not an expert but it didn’t take any effort for me to loosen them at all. I hope that’s the issue. Trying to get the arm off as we speak. I have a rubber mallet and I am tapping the arm. It has moved a little bit but not enough for me to remove it yet. |
https://cimg1.ibsrv.net/gimg/bikefor...0445a3f8a.jpeg
This side feels silky smooth. https://cimg1.ibsrv.net/gimg/bikefor...020896fec.jpeg This side isn’t as smooth as the non drive side but I don’t feel any of the bearings catching. Other than clean and re grease, which I plan on putting grease enfront and behind the bearings and also on the spindle. Is there anything else I should do? |
Originally Posted by LesterOfPuppets
(Post 22146145)
Yeah the little lady had the As on the big TV while I was watching minor league action on the computer in my office, I popped in for a little of the As game too. Mariners game starts pretty soon, but I'm picking up Five Guys right now...
|
Originally Posted by LAJ
(Post 22146158)
Yes indeed!
|
Originally Posted by big john
(Post 22146257)
Not checking in on the Suns?
|
At least football will be here soon.
|
Originally Posted by Velo Vol
(Post 22146267)
I've been there.
|
Originally Posted by Velo Vol
(Post 22146117)
Sad.
|
Originally Posted by Velo Vol
(Post 22146267)
I've been there.
|
All times are GMT -6. The time now is 12:36 AM. |
Copyright © 2024 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.