|
Salubrious , thanks for the link. I found a rim on eBay with local pickup for $40. Do we have wheelbuilders in the house? Because, I'll need to order the correct spokes to lace it up to my SA 3 speed.
|
[QUOTE=clubman;22176265]IMO, the original, older SA shifter cables with fulcrum stops are superior. Far less friction and typically, they are impervious to oxidation as well as accommodating wider variations of stem and bar combinations./QUOTE]
Originally Posted by ConnoisseurEqua
(Post 22176237)
I have 3 Raleighs and A Hercules. I never had a problem with any cable getting in my feet. The gear cable is protected. Therefore it does not tend to rust.
One of the Raleigh have that upper way and is totally open to the weather conditions, The pulley is rusted. Part of its restoration to come. [Still cant post pics.Frustrating] https://cimg5.ibsrv.net/gimg/bikefor...e76038f465.png https://cimg4.ibsrv.net/gimg/bikefor...b97f278ca8.png Do you think it could be cleaned/salvaged? . |
Originally Posted by Salubrious
(Post 22179179)
WRT brakes, if you were getting squealing with the new Kool Stops, you need to twist the calipers a bit so that the trailing edge of the brake pad contacts the rim first. It doesn't take much but if they set down at the same time along their length, the pads (and rim) will squeal.
|
[QUOTE=ConnoisseurEqua;22179446]
Originally Posted by clubman
(Post 22176265)
IMO, the original, older SA shifter cables with fulcrum stops are superior. Far less friction and typically, they are impervious to oxidation as well as accommodating wider variations of stem and bar combinations./QUOTE]
This is the reason I asked. Rust had a 3 courses meal on it. https://cimg5.ibsrv.net/gimg/bikefor...e76038f465.png https://cimg4.ibsrv.net/gimg/bikefor...b97f278ca8.png Do you think it could be cleaned/salvaged? . I just did the same thing on a bike that had been baked in the Arizona sun, so the rust was more surface rust than yours. It cleaned up well, whereas yours appears to have metal missing on the pulley mount. |
"pulley mount" That's what they are called.
I ride 3 speed but am rather newbie to name their parts. Thanks |
Originally Posted by theofam
(Post 22178639)
Finally hit 10 posts! Back in March a buddy gave me a couple old bikes he bought in a three-bike CL deal. He kept the Hawthorne. I got these rusty relics.
https://cimg5.ibsrv.net/gimg/bikefor...fcd48bc6f1.jpg On the right is a Schwinn. I've no idea what model (have yet to research it). On the left is a Western Flyer with a 3-speed SA hub dated 1960. The cotter crank was frozen. Many choice words were said getting it apart. I nearly scrapped the project due to difficulty removing the drive-side bearing cup. The SA hub was frozen. When I removed the rear wheel, the chain kept the same shape. You get the idea! After hours removing rust with white vinegar, aluminum foil and brass brushes, I moved on to the SA hub. https://cimg2.ibsrv.net/gimg/bikefor...7ee5e6cf8d.jpg Removing rust, piece by piece, was both a challenge and therapy. Fast forward a couple months. Being a motorcycle fan, I realized I could flip the bars and rotate them to give the appearance of a 1920s board track racer. I also frequent a coffee shop rife with nice mountain bikes parked outside. I figured if I kept the original paint/patina, folks would look right past my bike to focus on the high-dollar stuff. So, here's the Western Flyer: https://cimg4.ibsrv.net/gimg/bikefor...a27c28308a.jpg Being a coffee shop bike, and being born in '68, I had a plate made with its name - Mocha https://cimg6.ibsrv.net/gimg/bikefor...05b91ca950.jpg After 10-20 hours getting Mocha on the road, I figured my time was worth more than $3.25/hour. So, I picked up a coffee shop bike for my wife on CL for $70. It's name, you ask? Java. https://cimg3.ibsrv.net/gimg/bikefor...6c300946d8.jpg If you remove the fenders/chainguard, it's a full Scorcher. This is also a Semi Scorcher https://cimg9.ibsrv.net/gimg/bikefor...6cbdb4a95d.jpg No fenders, no chainguard but upturned bars. I quite like the look of the bars down but my neck and back disagree. |
Originally Posted by ConnoisseurEqua
(Post 22179491)
"pulley mount" That's what they are called.
I ride 3 speed but am rather newbie to name their parts. Thanks Love to see a wide shot of the drive side. These bikes are usually worth cleaning up. Parts are usually available, just replace. |
Originally Posted by gster
(Post 22179507)
You've built what we've been calling a Semi Scorcher.
If you remove the fenders/chainguard, it's a full Scorcher. This is also a Semi Scorcher https://cimg9.ibsrv.net/gimg/bikefor...6cbdb4a95d.jpg No fenders, no chainguard but upturned bars. I quite like the look of the bars down but my neck and back disagree. Thanks for the tutelage. Part of the fun for me taking on a new project(s) is learning the vocabulary associated with it. Each new endeavor makes me realize just how little I know of this world. |
I would call this bike a true Scorcher.
https://cimg8.ibsrv.net/gimg/bikefor...c1e28c2f0e.jpg Not one of my bikes but a very nice example. |
About the frozen pulley - the small securing screw on the pulley that holds the wheel on the axle is finely threaded, of small diameter, and made of relatively soft metal. One thing that may help is before removing the pulley from the frame, gently tap the flat bladed screw driver into the screw head slot using a hammer. Don't pound on it, but when setting the driver blade into the screw head, give the butt of the driver a little tap with a hammer to deliver a little shock to the screw. Sometimes this is enough to then turn the blade. If still frozen, add a little oil and try again. It's sort of like a very light-duty version of an impact driver. Do not attempt to force that small screw if it seems stuck - they strip or break.
|
Originally Posted by markk900
(Post 22179461)
Correct me if I am wrong but I always understood that you wanted toe *in* (leading edge to contact first)…. Exact same principle as described so maybe it doesn’t matter but just thought I should check.
|
Originally Posted by Salubrious
(Post 22180138)
I'm going with 'wrong' on that one... I can't imagine how you would get the calipers to work properly that way; if the leaded edge contacts first, it will cause the caliper to distort and since its springy metal, I have to imagine it would squeal like crazy! At any rate I've never tried that.
https://www.renehersecycles.com/a-be...adjust-toe-in/ Also St Sheldon suggests toe-in to prevent squeal: https://www.sheldonbrown.com/rim-brakes.html#squealing |
Originally Posted by theofam
(Post 22179272)
Salubrious , thanks for the link. I found a rim on eBay with local pickup for $40. Do we have wheelbuilders in the house? Because, I'll need to order the correct spokes to lace it up to my SA 3 speed.
Originally Posted by markk900
(Post 22180172)
Fair enough, though you got me to wondering where I thought that came from (because I have been adjusting for toe-in for years to eliminate squeal and wondered if I had been doing it improperly) and when I searched the interwebs it was clear that toe-in (leading edge touching slightly ahead of the rest of the pad) seemed to be the preferred method of setup..... here's one example:
https://www.renehersecycles.com/a-be...adjust-toe-in/ Also St Sheldon suggests toe-in to prevent squeal: https://www.sheldonbrown.com/rim-brakes.html#squealing |
Safe Clean
Hi
How do I clean up a Sturmey Archer gear shift? There are some colours on it which I intend to preserve. I tried common cleaners but no much changes. Thanks https://cimg9.ibsrv.net/gimg/bikefor...21858ecd5f.png https://cimg0.ibsrv.net/gimg/bikefor...dfa479d4e1.png |
Originally Posted by ConnoisseurEqua
(Post 22180589)
Hi
How do I clean up a Sturmey Archer gear shift? There are some colours on it which I intend to preserve. I tried common cleaners but no much changes. Thanks |
Originally Posted by ConnoisseurEqua
(Post 22180589)
Hi
How do I clean up a Sturmey Archer gear shift? There are some colours on it which I intend to preserve. I tried common cleaners but no much changes. Thanks https://cimg9.ibsrv.net/gimg/bikefor...21858ecd5f.png https://cimg0.ibsrv.net/gimg/bikefor...dfa479d4e1.png |
Wood Bleach aka diluted oxalic acid. Eats rust, not paint.
|
Originally Posted by gster
(Post 22179750)
I would call this bike a true Scorcher.
https://cimg8.ibsrv.net/gimg/bikefor...c1e28c2f0e.jpg Not one of my bikes but a very nice example. |
Originally Posted by 3speedslow
(Post 22180834)
Dude, that’s my bike! Honored that you would hold it up as an example.
|
Originally Posted by 3speedslow
(Post 22180834)
Dude, that’s my bike! Honored that you would hold it up as an example.
Nicely done. |
Thanks all! It’s a hoot to ride. A year has gone by since I could pull it out of the bike shed which I was finally able to do two days ago. Much rearranging of bikes, projects and stuff to keep or sell to be done.
As for that beaut, some air, a Brooks atop the post and away I will go! |
Don't see many of this brand for sale, and it's cheap.
https://www.facebook.com/marketplace...74259470715732 https://scontent.fric1-1.fna.fbcdn.n...8c&oe=613F1194 I guess I thought the bikes were manufactured in Canada, but evidently they were made for Canadian Tire in England. https://scontent.fric1-2.fna.fbcdn.n...d3&oe=613FAC53 |
Originally Posted by thumpism
(Post 22185092)
Don't see many of this brand for sale, and it's cheap.
https://scontent.fric1-2.fna.fbcdn.n...d3&oe=613FAC53 https://cimg8.ibsrv.net/gimg/bikefor...64b7cd06a5.jpg |
Sears-puch? Goodness.
25$ and wd40 made everything work. https://cimg4.ibsrv.net/gimg/bikefor...6e44fc2367.jpg |
I see your rear reflector is kaput like mine. Great Puch bike and will be a sweet cruiser for you. I am working on the men’s version in a month or so.
|
Originally Posted by 3speedslow
(Post 22185583)
I see your rear reflector is kaput like mine. Great Puch bike and will be a sweet cruiser for you. I am working on the men’s version in a month or so.
|
Does anyone know the difference between the KMC Z1 wide and the KMC S1?
It's for a Ralegh 3 speed SA hub The only difference I see is the slightly taller plates. |
Originally Posted by thumpism
(Post 22185092)
Don't see many of this brand for sale, and it's cheap.
https://www.facebook.com/marketplace...74259470715732 https://scontent.fric1-1.fna.fbcdn.n...8c&oe=613F1194 I guess I thought the bikes were manufactured in Canada, but evidently they were made for Canadian Tire in England. https://scontent.fric1-2.fna.fbcdn.n...d3&oe=613FAC53 of others over the years.. They're still selling bikes with the Supercycle label. No idea who supplies them now but mostly junk, in my opinion man. https://cimg4.ibsrv.net/gimg/bikefor...6c247046ac.jpg |
Originally Posted by rich110
(Post 22185766)
Does anyone know the difference between the KMC Z1 wide and the KMC S1?
It's for a Ralegh 3 speed SA hub The only difference I see is the slightly taller plates. These product descriptions are off of the amazonian juggernaut's website. Z1 product description: Features & detailsCompatible with all single speed drivetrains including; internal hub gear, BMX, track, fixed gear and mid motor e bikesHigh pin power with reinforced durabilityThicker outer plates for higher TORSION resistanceWider, bevelled inner plate more stable no drop designTensile strength 1200kgf.Brushless construction.Nickel plated.Supplied with joining link.1/2" X 1/8" pin length: 8.6 mm.112 links S1 product description: Features & detailsFor single speed use, Plate thickness and standard riveting Width: 8. 6mm/399g (112L)1/8th inchPackage Dimensions: 4" L x 3.9" W x 1" HCountry Of Origin : TaiwanSport type: CyclingFit type: Universal Fit Edit: My conclusion, the Z1 is a little better, a little more expensive, but both come from a reliable manufacturer. |
Is there a way to tell what year an old Hercules hub is?
Spotted this on fleabay: https://www.ebay.com/itm/234141863570 I was wondering if it would be correct for a mid 50's Hercules or were these newer? The bike I'm working on is old enough to have a BB oil port, and a Birmingham Head badge and fork. Did the Hercules branded hubs have a date code? The only markings I see on the hub on ebay is a 'B Type 4'. I wasn't sure if that gave the year or not? |
| All times are GMT -6. The time now is 02:46 PM. |
Copyright © 2023 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.