Using toolboxes for parts storage (and some cheap dividers)
#1
www.theheadbadge.com
Thread Starter
Join Date: Sep 2005
Location: Southern Florida
Posts: 28,602
Bikes: https://www.theheadbadge.com
Liked 4,538 Times
in
2,143 Posts
Using toolboxes for parts storage (and some cheap dividers)
I've been recently poking around at Vidmar tool boxes - apparently, I enjoy sticker shock at the tune of $700 for a cabinet of simple ball-bearing drawers - trying to come up with a decent solution for storing small bits in a manner that doesn't require me to pull my hair out.
I ultimately decided to experiment with this silly little 3/4 sized toolbox off Amazon (badged "ARTMAN" which is either a mildly humorous or deeply pathetic ripoff riff of "Craftsman"), as it clears the windowline and is small enough that the exit door isn't impeded. Not to say that something like this is worth it except for these edge case scenarios; the darn thing isn't cheap. Even getting a scratch-and-dent Amazon Warehouse job was $185, and they usually go for $200 + $50 shipping. When you consider that the Husky 42" boxes at Home Depot are running $279 or so - they're one of the best deals I know of at the moment - this tiny thing and it's pricing becomes outrageous.
Here's the DO-TOOL-THINGS-WITH-A-SEXIST-NAME box in what I expect to be its permanent spot in the shop (speaking of which, anyone know of a floor coating that isn't too industrial looking, durable to all the rust and grease that'll inevitably fall on it, and DIY-install friendly?).
The Akrobins on top will be removed eventually, in addition to the rest of the surrounding mess. Speaking of which, I'd like to replace the entire set of boxes to the left with 42" wide units, but the aforementioned Husky box has a wooden top, not a proper raised edge to keep stacker boxes from falling off. Plus, I'd much rather find a few old Craftsman units that allow me to mix-and-match drawers. Everyone on Facebook Marketplace seems to think their rusty Craftsman boxes are made out of 24 karat gold though, so that's unlikely to happen.
Side note, the FARTMAN drawers like to wander if you look at them a bit funny. Especially if they're carrying heavy loads. I'm constantly shoving the spoke drawer back in, as it loves to pop out.
At any rate, what is great is that the storage works surprisingly well when outfitted with these red dividers I found from Schaller Corporation (link for those curious). They sell their dividers as a sort of Vidmar alternative, but you can put them in anything (obviously). The main thing is they're sturdy and a lot cheaper overall in comparison to the flimsy stuff Amazon has right now (which are more or less light-duty desk organizers injection molded in black and not actual parts dividers).
The only downside to the Schallers is that the sizing available is arguably on the small side if you want to separate a pile of, say, freewheels or brake levers. Nevertheless, they do the job. I'm particularly enjoying the top 1" drawer. I can't tell you how frustrating these parts have always been to dig up in the existing Akrobins.
I'm still exploring options for the larger bits, so I'm open to seeing your solutions out there - especially if they're affordable. In total, I bought four drawers worth of Schaller dividers which ran about $80 shipped - not bad considering everything I bought and the quality of these things - but I'm really interested in any other methods that might not involve the need of an overpriced little squirt of a toolbox.
-Kurt
I ultimately decided to experiment with this silly little 3/4 sized toolbox off Amazon (badged "ARTMAN" which is either a mildly humorous or deeply pathetic ripoff riff of "Craftsman"), as it clears the windowline and is small enough that the exit door isn't impeded. Not to say that something like this is worth it except for these edge case scenarios; the darn thing isn't cheap. Even getting a scratch-and-dent Amazon Warehouse job was $185, and they usually go for $200 + $50 shipping. When you consider that the Husky 42" boxes at Home Depot are running $279 or so - they're one of the best deals I know of at the moment - this tiny thing and it's pricing becomes outrageous.
Here's the DO-TOOL-THINGS-WITH-A-SEXIST-NAME box in what I expect to be its permanent spot in the shop (speaking of which, anyone know of a floor coating that isn't too industrial looking, durable to all the rust and grease that'll inevitably fall on it, and DIY-install friendly?).
The Akrobins on top will be removed eventually, in addition to the rest of the surrounding mess. Speaking of which, I'd like to replace the entire set of boxes to the left with 42" wide units, but the aforementioned Husky box has a wooden top, not a proper raised edge to keep stacker boxes from falling off. Plus, I'd much rather find a few old Craftsman units that allow me to mix-and-match drawers. Everyone on Facebook Marketplace seems to think their rusty Craftsman boxes are made out of 24 karat gold though, so that's unlikely to happen.
Side note, the FARTMAN drawers like to wander if you look at them a bit funny. Especially if they're carrying heavy loads. I'm constantly shoving the spoke drawer back in, as it loves to pop out.
At any rate, what is great is that the storage works surprisingly well when outfitted with these red dividers I found from Schaller Corporation (link for those curious). They sell their dividers as a sort of Vidmar alternative, but you can put them in anything (obviously). The main thing is they're sturdy and a lot cheaper overall in comparison to the flimsy stuff Amazon has right now (which are more or less light-duty desk organizers injection molded in black and not actual parts dividers).
The only downside to the Schallers is that the sizing available is arguably on the small side if you want to separate a pile of, say, freewheels or brake levers. Nevertheless, they do the job. I'm particularly enjoying the top 1" drawer. I can't tell you how frustrating these parts have always been to dig up in the existing Akrobins.
I'm still exploring options for the larger bits, so I'm open to seeing your solutions out there - especially if they're affordable. In total, I bought four drawers worth of Schaller dividers which ran about $80 shipped - not bad considering everything I bought and the quality of these things - but I'm really interested in any other methods that might not involve the need of an overpriced little squirt of a toolbox.
-Kurt
Last edited by cudak888; 04-15-24 at 05:59 AM.
Likes For cudak888:
#2
Senior Member
I would suggest something like this;
https://www.harborfreight.com/20-bin...BoCfHYQAvD_BwE
$5.94 at Harbor Freight right now for the drawer and the organizers. Stack them in a corner - take them with you when you need to.
https://www.harborfreight.com/20-bin...BoCfHYQAvD_BwE
$5.94 at Harbor Freight right now for the drawer and the organizers. Stack them in a corner - take them with you when you need to.
Likes For ScottCommutes:
#3
www.theheadbadge.com
Thread Starter
Join Date: Sep 2005
Location: Southern Florida
Posts: 28,602
Bikes: https://www.theheadbadge.com
Liked 4,538 Times
in
2,143 Posts
Just my personal experience. Nevertheless, I'm curious how many are working with these and are content working with them.
-Kurt
#4
Full Member
#5
Senior Member
Join Date: Oct 2015
Location: PDX
Posts: 13,520
Bikes: Merz x 5 + Specialized Merz Allez x 2, Strawberry/Newlands/DiNucci/Ti x3, Gordon, Fuso/Moulton x2, Bornstein, Paisley,1958-74 Paramounts x3, 3rensho, 74 Moto TC, 73-78 Raleigh Pro's x5, Marinoni x2, 1960 Cinelli SC, 1980 Bianchi SC, PX-10 X 2
Liked 6,834 Times
in
3,900 Posts
[MENTION=40306]cudak888[/MENTION]
Curt, I went with silverware drawer divider/organizers, some screen/wire versions but there are more robust versions, some are not that cheap so.....
Curt, I went with silverware drawer divider/organizers, some screen/wire versions but there are more robust versions, some are not that cheap so.....
Likes For merziac:
#6
Edumacator
Join Date: Jan 2018
Location: Goose Creek, SC
Posts: 7,572
Bikes: '87 Crestdale, '87 Basso Gap, '92 Rossin Performance EL-OS, 1990 VanTuyl, 1980s Losa, 1985 Trek 670, 1982 AD SLE, 1987 PX10, etc...
Liked 3,596 Times
in
2,259 Posts
You can see the library microfiche filing cabinet that is my organizer for un-grouped parts...
__________________
1987 Crest Cannondale, 1987 Basso Gap, 1992 Rossin Performance EL, 1990ish Van Tuyl, 1985 Trek 670, 2003 Pinarello Surprise, 1990ish MBK Atlantique, 1987 Peugeot Competition, 1987 Nishiki Tri-A, 1981 Faggin, 1996 Cannondale M500, 1984 Mercian, 1982 AD SuperLeicht, 1985 Massi (model unknown), 1988 Daccordi Griffe , 1989 Fauxsin MTB, 1981 Ciocc Mockba, 1992 Bianchi Giro, 1977 Colnago Super, 1971 Raleigh International, 1998 Corratec Ap & Dun, 1991 Peugeot Slimestone
1987 Crest Cannondale, 1987 Basso Gap, 1992 Rossin Performance EL, 1990ish Van Tuyl, 1985 Trek 670, 2003 Pinarello Surprise, 1990ish MBK Atlantique, 1987 Peugeot Competition, 1987 Nishiki Tri-A, 1981 Faggin, 1996 Cannondale M500, 1984 Mercian, 1982 AD SuperLeicht, 1985 Massi (model unknown), 1988 Daccordi Griffe , 1989 Fauxsin MTB, 1981 Ciocc Mockba, 1992 Bianchi Giro, 1977 Colnago Super, 1971 Raleigh International, 1998 Corratec Ap & Dun, 1991 Peugeot Slimestone
#7
www.theheadbadge.com
Thread Starter
Join Date: Sep 2005
Location: Southern Florida
Posts: 28,602
Bikes: https://www.theheadbadge.com
Liked 4,538 Times
in
2,143 Posts
Likes For cudak888:
#8
Edumacator
Join Date: Jan 2018
Location: Goose Creek, SC
Posts: 7,572
Bikes: '87 Crestdale, '87 Basso Gap, '92 Rossin Performance EL-OS, 1990 VanTuyl, 1980s Losa, 1985 Trek 670, 1982 AD SLE, 1987 PX10, etc...
Liked 3,596 Times
in
2,259 Posts
Problem is, I am so efficient with the garage it masks how much too much I have...
#9
www.theheadbadge.com
Thread Starter
Join Date: Sep 2005
Location: Southern Florida
Posts: 28,602
Bikes: https://www.theheadbadge.com
Liked 4,538 Times
in
2,143 Posts
Likes For cudak888:
#10
Edumacator
Join Date: Jan 2018
Location: Goose Creek, SC
Posts: 7,572
Bikes: '87 Crestdale, '87 Basso Gap, '92 Rossin Performance EL-OS, 1990 VanTuyl, 1980s Losa, 1985 Trek 670, 1982 AD SLE, 1987 PX10, etc...
Liked 3,596 Times
in
2,259 Posts
Maybe a surplus library or school district sale?
__________________
1987 Crest Cannondale, 1987 Basso Gap, 1992 Rossin Performance EL, 1990ish Van Tuyl, 1985 Trek 670, 2003 Pinarello Surprise, 1990ish MBK Atlantique, 1987 Peugeot Competition, 1987 Nishiki Tri-A, 1981 Faggin, 1996 Cannondale M500, 1984 Mercian, 1982 AD SuperLeicht, 1985 Massi (model unknown), 1988 Daccordi Griffe , 1989 Fauxsin MTB, 1981 Ciocc Mockba, 1992 Bianchi Giro, 1977 Colnago Super, 1971 Raleigh International, 1998 Corratec Ap & Dun, 1991 Peugeot Slimestone
1987 Crest Cannondale, 1987 Basso Gap, 1992 Rossin Performance EL, 1990ish Van Tuyl, 1985 Trek 670, 2003 Pinarello Surprise, 1990ish MBK Atlantique, 1987 Peugeot Competition, 1987 Nishiki Tri-A, 1981 Faggin, 1996 Cannondale M500, 1984 Mercian, 1982 AD SuperLeicht, 1985 Massi (model unknown), 1988 Daccordi Griffe , 1989 Fauxsin MTB, 1981 Ciocc Mockba, 1992 Bianchi Giro, 1977 Colnago Super, 1971 Raleigh International, 1998 Corratec Ap & Dun, 1991 Peugeot Slimestone
Likes For jdawginsc:
#11
www.theheadbadge.com
Thread Starter
Join Date: Sep 2005
Location: Southern Florida
Posts: 28,602
Bikes: https://www.theheadbadge.com
Liked 4,538 Times
in
2,143 Posts
Our County library digitized a lot of our microfiche over the last decade. Might still be a cabinet out there that hasn't been divested from inventory yet.
Local uni also has a surplus department that I frequent.
-Kurt
Local uni also has a surplus department that I frequent.
-Kurt
#12
Randomhead
Join Date: Aug 2008
Location: Happy Valley, Pennsylvania
Posts: 24,893
Liked 4,051 Times
in
2,757 Posts
The only problem with using tool chests for storage becomes apparent if you ever have to empty them. I decided to repurpose one for the storage of tools, and the stuff I had in there filled up 6 large storage bins.
#13
www.theheadbadge.com
Thread Starter
Join Date: Sep 2005
Location: Southern Florida
Posts: 28,602
Bikes: https://www.theheadbadge.com
Liked 4,538 Times
in
2,143 Posts
-Kurt
Last edited by cudak888; 04-15-24 at 08:12 AM.
#14
Senior Member
Join Date: Nov 2005
Location: NW Ohio
Posts: 3,556
Bikes: 1984 Miyata 310, 1986 Schwinn Sierra, 2011 Jamis Quest, 1980 Peugeot TH8 Tandem, 1992 Performance Parabola, 1987 Ross Mt. Hood, 1988 Schwinn LeTour, 1988 Trek 400T, 1981 Fuji S12-S LTD, 197? FW Evans
Liked 1,244 Times
in
605 Posts
When I retired, I told my wife I wanted my retirement present to be a nice garage cabinet system to replace the mish-mash of workbenches, cupboards, and wire shelves that I had accumulated over the years. I got these from Home Depot. I'm still getting it organized (it's been over a year), but I like the wide flat drawers for bike components because I can pull them open and see what's there without digging through a bin. The bottom drawers are deep enough to store handlebars and saddles One drawback for this model is the drawer slides are not full length, so the drawers don't pull all the way out. The upper cabinets came with LED under cabinet lights to illuminate the bench. These pictures are from when I first put them in, so there is a lot more clutter now.
The bike corner. I use the plastic vise a lot to hold alloy parts. It doesn't have the same grip as a steel vise, but it is handy when you need a third hand, plus it doesn't scratch the soft metal.
General work area. The wall above the work bench is now covered with pegboard and I mounted my vise on the corner.
The bike corner. I use the plastic vise a lot to hold alloy parts. It doesn't have the same grip as a steel vise, but it is handy when you need a third hand, plus it doesn't scratch the soft metal.
General work area. The wall above the work bench is now covered with pegboard and I mounted my vise on the corner.
#15
Military ammo boxes. You either have people trying to sell them for $20+ each or $5 each once they realize that the full pallet of them they bought isn't moving. I have a number of them in a shelf I use to store medium size parts. The next time I find a bunch for cheap I plan on finding a shelving unit where they can fit perfectly. Add a bunch of magnetic tags and you got yourself a super solid solution for cheap
Likes For abdon:
#16
Full Member
Likes For BMC_Kid:
#17
Edumacator
Join Date: Jan 2018
Location: Goose Creek, SC
Posts: 7,572
Bikes: '87 Crestdale, '87 Basso Gap, '92 Rossin Performance EL-OS, 1990 VanTuyl, 1980s Losa, 1985 Trek 670, 1982 AD SLE, 1987 PX10, etc...
Liked 3,596 Times
in
2,259 Posts
It was an eye opener how many redundancies I had and extra groups. I had to compare them against wheels and frame sets and it sort of made me a bit queasy at the excess (thus the sales).
__________________
1987 Crest Cannondale, 1987 Basso Gap, 1992 Rossin Performance EL, 1990ish Van Tuyl, 1985 Trek 670, 2003 Pinarello Surprise, 1990ish MBK Atlantique, 1987 Peugeot Competition, 1987 Nishiki Tri-A, 1981 Faggin, 1996 Cannondale M500, 1984 Mercian, 1982 AD SuperLeicht, 1985 Massi (model unknown), 1988 Daccordi Griffe , 1989 Fauxsin MTB, 1981 Ciocc Mockba, 1992 Bianchi Giro, 1977 Colnago Super, 1971 Raleigh International, 1998 Corratec Ap & Dun, 1991 Peugeot Slimestone
1987 Crest Cannondale, 1987 Basso Gap, 1992 Rossin Performance EL, 1990ish Van Tuyl, 1985 Trek 670, 2003 Pinarello Surprise, 1990ish MBK Atlantique, 1987 Peugeot Competition, 1987 Nishiki Tri-A, 1981 Faggin, 1996 Cannondale M500, 1984 Mercian, 1982 AD SuperLeicht, 1985 Massi (model unknown), 1988 Daccordi Griffe , 1989 Fauxsin MTB, 1981 Ciocc Mockba, 1992 Bianchi Giro, 1977 Colnago Super, 1971 Raleigh International, 1998 Corratec Ap & Dun, 1991 Peugeot Slimestone
Likes For jdawginsc:
#18
Senior Member
Join Date: Jul 2022
Location: Pac NW
Posts: 2,393
Bikes: several Eddy Merz (ride like Eddy, braze like Jim!)
Liked 2,278 Times
in
828 Posts
Kurt, find a local used medical supply store.
I took some of my dad's dental chairs in and was amazed at the cabinets available. Cheap too. Often with dividers in drawers.
example shown: It sold for much less if I recall. Bonus if you like older Celeste style green.
https://www.invaluable.com/auction-l...2-c-89a4a07967
I took some of my dad's dental chairs in and was amazed at the cabinets available. Cheap too. Often with dividers in drawers.
example shown: It sold for much less if I recall. Bonus if you like older Celeste style green.
https://www.invaluable.com/auction-l...2-c-89a4a07967
__________________
"Leave the gun. Take the Colnagos."
"Leave the gun. Take the Colnagos."
Likes For Robvolz:
#19
1991 PBP Anciens
Join Date: Nov 2009
Location: Elburn, Illannoy
Posts: 726
Bikes: 1954 Robin Hood, 1964 Dunelt, 1968 Raleigh Superbe, 1969 Robin Hood, 197? Gitane, 1973 Raleigh SuperCourse, 1981 Miyata 710, 1990 Miyata 600GT, 2007 Rivendell Bleriot
Liked 498 Times
in
190 Posts
That's some impressive organization you guys have. I roll like this.
Before I retired, I was that one guy with the seemingly disorganized desk.Yet I knew where everything was.
Before I retired, I was that one guy with the seemingly disorganized desk.Yet I knew where everything was.
#20
too many bikes
Found my parts storage drawers on the curb
It was my lucky day. Drawers are a huge improvement from keeping small stuff in boxes. I’m too lazy to organize within the drawers. I was lucky again
when my wife found an old card catalog on the curb in our neighborhood. As a hobbyist woodworker, I’ve been on the lookout for one forever.
when my wife found an old card catalog on the curb in our neighborhood. As a hobbyist woodworker, I’ve been on the lookout for one forever.
#21
Senior Member
Join Date: May 2019
Location: Bloomington, IN
Posts: 3,196
Bikes: Paramount, Faggin, Ochsner, Ciocc, Basso
Liked 2,187 Times
in
1,275 Posts
Kurt,
As much as I like you I don't think I'm gonna spend another dime on tool or part storage. Just look at all this storage and I still don't have enough and I'm beginning to think I need to down size.
40" of eleven drawers full of auto mechanic's tools, and those MAC and Snap-On items cost me plenty.
And another 40" of eleven drawers full of bike shop specialty tools.
And this six feet of Tool box and bench storage.
And this twelve feet of golf shop equipment. with at least 12 drawers of part storage.
And three ($4k@) golf club bending machines.
And the eight feet of drawer storage behind the bending machines.
And a 4foot by 4 foot workbench with twenty drawers under it.
And the carport tool box with mostly bike tools in it 40'" by three feet in four drawers. And a tail shelf with a 4"vise hanging off the side.
Smiles, MH
As much as I like you I don't think I'm gonna spend another dime on tool or part storage. Just look at all this storage and I still don't have enough and I'm beginning to think I need to down size.
40" of eleven drawers full of auto mechanic's tools, and those MAC and Snap-On items cost me plenty.
And another 40" of eleven drawers full of bike shop specialty tools.
And this six feet of Tool box and bench storage.
And this twelve feet of golf shop equipment. with at least 12 drawers of part storage.
And three ($4k@) golf club bending machines.
And the eight feet of drawer storage behind the bending machines.
And a 4foot by 4 foot workbench with twenty drawers under it.
And the carport tool box with mostly bike tools in it 40'" by three feet in four drawers. And a tail shelf with a 4"vise hanging off the side.
Smiles, MH
Last edited by Mad Honk; 04-15-24 at 09:49 PM.
#22
Senior Member
Join Date: Mar 2021
Location: SoCal
Posts: 2,944
Bikes: Cuevas Custom, Cimmaron, 1988 "Pinalized Rockma", 1984 Trek 510, Moulton custom touring, Raleigh Competition GS, Bridgestone Mb-2 & 3, 1980's Peugeot - US, City, & Canyon Express (6)
Liked 4,893 Times
in
2,286 Posts
Metal and bearing drawers seems smart, I am working with what I already have. Nice wood flat files, smaller blonde sets and larger/darker 15 drawer pair.
Kept their original labels just to make things confusing
Cerussite Chalcanthite = Brake pads & hardware
I still have 15 + empty drawers in the big cabinets
Kept their original labels just to make things confusing
Cerussite Chalcanthite = Brake pads & hardware
I still have 15 + empty drawers in the big cabinets
Last edited by SoCaled; 04-15-24 at 05:43 PM.
#23
www.theheadbadge.com
Thread Starter
Join Date: Sep 2005
Location: Southern Florida
Posts: 28,602
Bikes: https://www.theheadbadge.com
Liked 4,538 Times
in
2,143 Posts
Kurt,
As much as I like you I don't think I'm gonna spend another dime on tool or part storage. Just look at all this storage and I still don't have enough and I'm beginning to think I need to down size.
40" of eleven drawers full of auto mechanic's tools, and those MAC and Snap-On items cost me plenty.
And another 40" of eleven drawers full of bike shop specialty tools.
And this six feet of Tool box and bench storage.
And this twelve feet of golf shop equipment. with at least 12 drawers of part storage.
And three ($4k@) golf club bending machines.
And the eight feet of drawer storage behind the bending machines.
And a 4foot by 4 foot workbench with twenty drawers under it.
And the carport tool box with mostly bike tools in it 40' by three feet in four drawers. And a tail shelf with a 4"vise hanging off the side.
Smiles, MH
As much as I like you I don't think I'm gonna spend another dime on tool or part storage. Just look at all this storage and I still don't have enough and I'm beginning to think I need to down size.
40" of eleven drawers full of auto mechanic's tools, and those MAC and Snap-On items cost me plenty.
And another 40" of eleven drawers full of bike shop specialty tools.
And this six feet of Tool box and bench storage.
And this twelve feet of golf shop equipment. with at least 12 drawers of part storage.
And three ($4k@) golf club bending machines.
And the eight feet of drawer storage behind the bending machines.
And a 4foot by 4 foot workbench with twenty drawers under it.
And the carport tool box with mostly bike tools in it 40' by three feet in four drawers. And a tail shelf with a 4"vise hanging off the side.
Smiles, MH
It was my lucky day. Drawers are a huge improvement from keeping small stuff in boxes. I’m too lazy to organize within the drawers. I was lucky again
when my wife found an old card catalog on the curb in our neighborhood. As a hobbyist woodworker, I’ve been on the lookout for one forever.
when my wife found an old card catalog on the curb in our neighborhood. As a hobbyist woodworker, I’ve been on the lookout for one forever.
Been there, done that, and don't ever need to do it again
-Kurt
#24
Senior Member
Everybody up here in northern Illinois is liquidating and moving down by you. With all the townwide garage sales and estate sales going on right now you could fill a U-Haul with toolboxes in a weekend, some full of tools.
__________________
Be where your feet are.......Lisa Bluder
Be where your feet are.......Lisa Bluder
#25
Senior Member
Here’s my setup for the bits I need the most, sorta semi-controlled chaos:
Of note is that the unit on the left of the first pic and the red cabinets in the second all came from IKEA. The first is meant to be an organizer for a kid’s room, but the modular design is quite handy.
Of note is that the unit on the left of the first pic and the red cabinets in the second all came from IKEA. The first is meant to be an organizer for a kid’s room, but the modular design is quite handy.
Likes For nlerner: