Any downsides to Nitto Noodle handlebars?
#1
Full Member
Thread Starter
Any downsides to Nitto Noodle handlebars?
The anatomical handlebars that came on my latest ride are not doing it for me. So, looking at the Nitto Noodle bars. I like the longer straight grip area on the drops. They also have a more “traditional” look. And wider bars are readily available. I will be running brifters.
My question is are there any downsides to the Noodles? Brifters not a good thing because of bend? Other issues?
Any other recommendations for other like bends (44cm on top and 26.0@ stem ) in a similar price range?
thanks
My question is are there any downsides to the Noodles? Brifters not a good thing because of bend? Other issues?
Any other recommendations for other like bends (44cm on top and 26.0@ stem ) in a similar price range?
thanks
#2
Senior Member
Join Date: Jul 2007
Location: South shore, L.I., NY
Posts: 6,857
Bikes: Flyxii FR322, Cannondale Topstone, Miyata City Liner, Specialized Chisel, Specialized Epic Evo
Mentioned: 18 Post(s)
Tagged: 0 Thread(s)
Quoted: 3221 Post(s)
Liked 2,048 Times
in
1,170 Posts
The sweep back at the bend tends to position the shifters - and your hands, about 10cm back then when using a more typical ergonomic bar. Thus you might want a longer stem.
Likes For Steve B.:
#3
Extraordinary Magnitude
Join Date: Aug 2009
Location: Waukesha WI
Posts: 13,642
Bikes: 1978 Trek TX700; 1978/79 Trek 736; 1984 Specialized Stumpjumper Sport; 1984 Schwinn Voyageur SP; 1985 Trek 620; 1985 Trek 720; 1986 Trek 400 Elance; 1987 Schwinn High Sierra; 1990 Miyata 1000LT
Mentioned: 84 Post(s)
Tagged: 0 Thread(s)
Quoted: 2607 Post(s)
Liked 1,694 Times
in
933 Posts
I love the B177 bars. Like anything, there's people that love them and people that don't love them.
People always compare/refer to the B177 as 'rando' bars, but they're kind of 'anti-rando' bars. Instead of a rise at the corners, they dip down. There's a slight sweep back at the corner that goes back- but I think that's pretty well offset by the long ramp. They do have a slight flare- but it's minimal compared to other 'rando' bars. I have nerve damage in my left hand, so I spend a lot of time riding on the corners and tops- they work for me.
Again, keep in mind that bars are measured at the ends, and there is a bit of splay- so a 44 is going to feel slightly narrower than a non-splayed out 44.
IMG_1703 by Dave The Golden Boy, on Flickr
Command Shifter + RRL Lever by Dave The Golden Boy, on Flickr
People always compare/refer to the B177 as 'rando' bars, but they're kind of 'anti-rando' bars. Instead of a rise at the corners, they dip down. There's a slight sweep back at the corner that goes back- but I think that's pretty well offset by the long ramp. They do have a slight flare- but it's minimal compared to other 'rando' bars. I have nerve damage in my left hand, so I spend a lot of time riding on the corners and tops- they work for me.
Again, keep in mind that bars are measured at the ends, and there is a bit of splay- so a 44 is going to feel slightly narrower than a non-splayed out 44.
IMG_1703 by Dave The Golden Boy, on Flickr
Command Shifter + RRL Lever by Dave The Golden Boy, on Flickr
__________________
*Recipient of the 2006 Time Magazine "Person Of The Year" Award*
Commence to jigglin’ huh?!?!
"But hey, always love to hear from opinionated amateurs." -says some guy to Mr. Marshall.
Commence to jigglin’ huh?!?!
"But hey, always love to hear from opinionated amateurs." -says some guy to Mr. Marshall.
Likes For The Golden Boy:
#4
Full Member
Join Date: Jul 2007
Location: San Francisco
Posts: 230
Bikes: 87 Raleigh 531C Team Replica, 96 Litespeed Classic, 01 Lemond Tete-De-Course, 99 Mongoose RX10.9, 03 Lemond Wayzata, 00 Litespeed Appalachian, 99 Bianchi XL Boron, 98 Litespeed Tuscany
Mentioned: 1 Post(s)
Tagged: 0 Thread(s)
Quoted: 35 Post(s)
Liked 53 Times
in
27 Posts
I use Noodles on two of my bikes I really like them. Some people may find the drops too deep if they are used to the newer style compact short reach/short drop bars. I think the Noodles work great on a classic bike. I had no problems mounting my Campy Ergo shifters on them.
'87 Raleigh
original_26a4438c-b96d-415a-8783-70482de39d1f_IMG_20221103_174416258 (1) by warren t., on Flickr
'96 Litespeed
IMG_20220908_180553595_HDR by warren t., on Flickr
'87 Raleigh
original_26a4438c-b96d-415a-8783-70482de39d1f_IMG_20221103_174416258 (1) by warren t., on Flickr
'96 Litespeed
IMG_20220908_180553595_HDR by warren t., on Flickr
Likes For Warren128:
Likes For jet sanchEz:
#6
Senior Member
Join Date: May 2013
Location: Pacific Northwest
Posts: 1,989
Bikes: ‘87 Marinoni SLX Sports Tourer, ‘79 Miyata 912 by Gugificazione
Mentioned: 166 Post(s)
Tagged: 0 Thread(s)
Quoted: 500 Post(s)
Liked 466 Times
in
256 Posts
Another Nitto Noodle fan here. They’re (42cm) on both my bikes, no downside that I sense, although I didn’t care for the 44cm version; 40cm would probably be “ideal” for narrow-shouldered me.
Compared to compact bars like Soma Hwy One (with 2cm longer stem, so identical reach), which I’ve also used quite a bit, I find that there’s room for more hand positions around the ramps on Noodles, so more options to offset hand issues. FWIW, I briefly tried SR’s version of rando bars with upward tilted ramps, and didn’t find any magic comfort unlike what BQ often says.
I use mine with early Campy Ergo brifters, and intentionally set them up with the brifters slightly higher on the bends. (I’m older and stiffer at 73, but still riding without any motors!)
Noodles:
For comparison, Hwy On (image intentionally reversed):
Compared to compact bars like Soma Hwy One (with 2cm longer stem, so identical reach), which I’ve also used quite a bit, I find that there’s room for more hand positions around the ramps on Noodles, so more options to offset hand issues. FWIW, I briefly tried SR’s version of rando bars with upward tilted ramps, and didn’t find any magic comfort unlike what BQ often says.
I use mine with early Campy Ergo brifters, and intentionally set them up with the brifters slightly higher on the bends. (I’m older and stiffer at 73, but still riding without any motors!)
Noodles:
For comparison, Hwy On (image intentionally reversed):
Likes For Dfrost:
#7
Senior Member
Join Date: Jul 2007
Location: South shore, L.I., NY
Posts: 6,857
Bikes: Flyxii FR322, Cannondale Topstone, Miyata City Liner, Specialized Chisel, Specialized Epic Evo
Mentioned: 18 Post(s)
Tagged: 0 Thread(s)
Quoted: 3221 Post(s)
Liked 2,048 Times
in
1,170 Posts
Its a very comfortable bar, I have them on my tourer. I like that its flat'ish behind the shifters/brake levers.
Likes For Steve B.:
#8
Full Member
Thread Starter
Thank you all for your informative replies. I do believe a set of Noodles is in my future.
#9
Disraeli Gears
Tried and didn't like. The sweep-back from the stem was anti-ergonomic for me; much prefer bars that sweep forward like a set of track bars. Nitto made a B-155 model (I think) that fit that bill very well, but I can't find any more than the single example I bought on eBay -- must have discontinued it.
Last edited by Charles Wahl; 11-06-22 at 06:47 PM.
#10
john903
Join Date: May 2012
Location: Sequim,WA
Posts: 55
Bikes: Curtlo, CHE cos'e,
Mentioned: 3 Post(s)
Tagged: 0 Thread(s)
Quoted: 27 Post(s)
Likes: 0
Liked 36 Times
in
15 Posts
I am one of the few who did not care for the swept back tops. I felt like I was was being pushed back. I suppose a longer stem would have worked but then the brake hoods would have been to far away. I did really like the feel of the drops though.
#11
Me duelen las nalgas
Join Date: Aug 2015
Location: Texas
Posts: 13,513
Bikes: Centurion Ironman, Trek 5900, Univega Via Carisma, Globe Carmel
Mentioned: 199 Post(s)
Tagged: 0 Thread(s)
Quoted: 4559 Post(s)
Liked 2,802 Times
in
1,800 Posts
I have a drop bar that's essentially similar to the Nitto Noodle in a box. Forget the brand and name but compared the specs back in 2018 or 2019 when I got 'em. Very traditional, pretty similar to the Winpista on my Centurion Ironman.
I like that kind of bar with brake-only setups, with downtube or bar-end shifters. Usually a stem in the 110-120mm length (I'm 5'11" with longish arms), although with age and neck problems I sometimes prefer a slighter shorter stem, or some other way to reduce the reach and sit upright just a bit more.
But I didn't like that bar design with brifters. For example, the MicroShift 7-speed brifters I used on one bike extended the reach quite a bit more than was comfortable for me. I switched to the FSA Omega Compact drops. Perfect.
FWIW, the Soma Hwy One drops shown above are identical to the configuration of the FSA Omega Compact drops. The only difference is the tubing diameter and stem size. But the reach, drop and length of the bar-ends are identical. I have both. The FSA Omega is currently on a 2010 or so Diamondback Podium with brifters and a 120-130mm stem. The Soma Hwy One is the smaller diameter tubing and will go on my 1993 Trek 5900 OCLV, which is basically built like a carbon fiber version of a classic steel road bike, with an early version of a 1" threadless headset. At a glance it resembles a quill stem, unless you notice there's no bolt on top to lock in the wedge. The somewhat more svelte Soma Hwy One better suits the lines of that bike. And the shorter reach across the top makes for a smoother transition to brifters.
I like that kind of bar with brake-only setups, with downtube or bar-end shifters. Usually a stem in the 110-120mm length (I'm 5'11" with longish arms), although with age and neck problems I sometimes prefer a slighter shorter stem, or some other way to reduce the reach and sit upright just a bit more.
But I didn't like that bar design with brifters. For example, the MicroShift 7-speed brifters I used on one bike extended the reach quite a bit more than was comfortable for me. I switched to the FSA Omega Compact drops. Perfect.
FWIW, the Soma Hwy One drops shown above are identical to the configuration of the FSA Omega Compact drops. The only difference is the tubing diameter and stem size. But the reach, drop and length of the bar-ends are identical. I have both. The FSA Omega is currently on a 2010 or so Diamondback Podium with brifters and a 120-130mm stem. The Soma Hwy One is the smaller diameter tubing and will go on my 1993 Trek 5900 OCLV, which is basically built like a carbon fiber version of a classic steel road bike, with an early version of a 1" threadless headset. At a glance it resembles a quill stem, unless you notice there's no bolt on top to lock in the wedge. The somewhat more svelte Soma Hwy One better suits the lines of that bike. And the shorter reach across the top makes for a smoother transition to brifters.
#12
2k miles from the midwest
Join Date: Feb 2005
Location: Washington
Posts: 1,964
Bikes: ~'75 Colin Laing, '80s Schwinn SuperSport 650b, ex-Backroads ti project...
Mentioned: 18 Post(s)
Tagged: 0 Thread(s)
Quoted: 525 Post(s)
Liked 931 Times
in
446 Posts
The only downside is availability in certain sizes and how much inflation/transport costs have made the price rise since '`19
Likes For Dylansbob:
#13
Senior Member
Join Date: Jul 2022
Location: Pac NW
Posts: 1,928
Bikes: several Eddy Merz (ride like Eddy, braze like Jim!)
Mentioned: 40 Post(s)
Tagged: 0 Thread(s)
Quoted: 1078 Post(s)
Liked 1,801 Times
in
655 Posts
OK, can someone send me a link to, or explain why the C & V crowd has a love affair with NITTO?
While sorting through parts at the co-op, my heart jumps when I think I found a Cinelli or 3TTT, but no, its another NITTO.
We even have them in the glass cases because someone thought they were valuable.
We have so many down there, I want to find an art project for them, coat hooks maybe? Antlers?
I have no hatred towards non-Italian parts, and I'm not a purist. My Italian car has tires made in Korea.
but I've seen restored Pinerellos with NITTOs and everyone else seems great with it.
What is their story?
While sorting through parts at the co-op, my heart jumps when I think I found a Cinelli or 3TTT, but no, its another NITTO.
We even have them in the glass cases because someone thought they were valuable.
We have so many down there, I want to find an art project for them, coat hooks maybe? Antlers?
I have no hatred towards non-Italian parts, and I'm not a purist. My Italian car has tires made in Korea.
but I've seen restored Pinerellos with NITTOs and everyone else seems great with it.
What is their story?
__________________
"Leave the gun. Take the Colnagos."
"Leave the gun. Take the Colnagos."
#14
Senior Member
Join Date: Sep 2005
Location: Oakland, CA
Posts: 3,265
Bikes: '82 Univega Competizione, '72 Motobecane Grand Record, '83 Mercian KOM Touring, '85 Univega Alpina Uno, '76 Eisentraut Limited
Mentioned: 57 Post(s)
Tagged: 0 Thread(s)
Quoted: 1088 Post(s)
Liked 1,205 Times
in
701 Posts
OK, can someone send me a link to, or explain why the C & V crowd has a love affair with NITTO?
While sorting through parts at the co-op, my heart jumps when I think I found a Cinelli or 3TTT, but no, its another NITTO.
We even have them in the glass cases because someone thought they were valuable.
We have so many down there, I want to find an art project for them, coat hooks maybe? Antlers?
I have no hatred towards non-Italian parts, and I'm not a purist. My Italian car has tires made in Korea.
but I've seen restored Pinerellos with NITTOs and everyone else seems great with it.
What is their story?
While sorting through parts at the co-op, my heart jumps when I think I found a Cinelli or 3TTT, but no, its another NITTO.
We even have them in the glass cases because someone thought they were valuable.
We have so many down there, I want to find an art project for them, coat hooks maybe? Antlers?
I have no hatred towards non-Italian parts, and I'm not a purist. My Italian car has tires made in Korea.
but I've seen restored Pinerellos with NITTOs and everyone else seems great with it.
What is their story?
#15
Senior Member
Join Date: Jul 2022
Location: Pac NW
Posts: 1,928
Bikes: several Eddy Merz (ride like Eddy, braze like Jim!)
Mentioned: 40 Post(s)
Tagged: 0 Thread(s)
Quoted: 1078 Post(s)
Liked 1,801 Times
in
655 Posts
sounds great. I couldn't fathom them being small from all the bars that come in. Love a company that treats employees with respect.
where they ever stock pieces in euro bikes?
where they ever stock pieces in euro bikes?
__________________
"Leave the gun. Take the Colnagos."
"Leave the gun. Take the Colnagos."
#17
Am-a-tour
Join Date: Aug 2020
Location: NOVA
Posts: 126
Bikes: 2020 New Albion Privateer, 1983 Schwinn Super Sport, 2022 Rivendell Atlantis
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 44 Post(s)
Liked 65 Times
in
40 Posts
I ran a set of 44s for about two years on my New Albion, and now run 46, both with short-ish stems to compensate for their long reach to the hoods. I'm about 6'3, 210lbs and really like all of the hand positions and the flats up to the hoods, as was mentioned above.
#18
Senior Member
Join Date: Jul 2007
Location: South shore, L.I., NY
Posts: 6,857
Bikes: Flyxii FR322, Cannondale Topstone, Miyata City Liner, Specialized Chisel, Specialized Epic Evo
Mentioned: 18 Post(s)
Tagged: 0 Thread(s)
Quoted: 3221 Post(s)
Liked 2,048 Times
in
1,170 Posts
One downside, is if not doing a C&V threaded stem, it can be harder to find a threadless stem in 26.0.
#19
Senior Member
Join Date: Dec 2015
Location: Menomonee Falls, WI
Posts: 1,832
Bikes: 1984 Schwinn Supersport, 1988 Trek 400T, 1977 Trek TX900, 1982 Bianchi Champione del Mondo, 1978 Raleigh Supercourse, 1986 Trek 400 Elance, 1991 Waterford PDG OS Paramount, 1971 Schwinn Sports Tourer, 1985 Trek 670
Mentioned: 7 Post(s)
Tagged: 0 Thread(s)
Quoted: 603 Post(s)
Liked 1,062 Times
in
534 Posts
No downside to anything Nitto makes, except availability.
Tim
Tim
#20
Senior Member
Join Date: Jul 2006
Location: San Jose (Willow Glen) Ca
Posts: 9,834
Bikes: Kirk Custom JK Special, '84 Team Miyata,(dura ace old school) 80?? SR Semi-Pro 600 Arabesque
Mentioned: 106 Post(s)
Tagged: 0 Thread(s)
Quoted: 2337 Post(s)
Liked 2,811 Times
in
1,535 Posts
OK, can someone send me a link to, or explain why the C & V crowd has a love affair with NITTO?
While sorting through parts at the co-op, my heart jumps when I think I found a Cinelli or 3TTT, but no, its another NITTO.
We even have them in the glass cases because someone thought they were valuable.
We have so many down there, I want to find an art project for them, coat hooks maybe? Antlers?
I have no hatred towards non-Italian parts, and I'm not a purist. My Italian car has tires made in Korea.
but I've seen restored Pinerellos with NITTOs and everyone else seems great with it.
What is their story?
While sorting through parts at the co-op, my heart jumps when I think I found a Cinelli or 3TTT, but no, its another NITTO.
We even have them in the glass cases because someone thought they were valuable.
We have so many down there, I want to find an art project for them, coat hooks maybe? Antlers?
I have no hatred towards non-Italian parts, and I'm not a purist. My Italian car has tires made in Korea.
but I've seen restored Pinerellos with NITTOs and everyone else seems great with it.
What is their story?
next build is full nitto cockpit noodle, pearl stem and double bolt seatpost
Nitto did the stems and seat post for shimano dura ace back in the olden days
__________________
Life is too short not to ride the best bike you have, as much as you can
(looking for Torpado Super light frame/fork or for Raleigh International frame fork 58cm)
Life is too short not to ride the best bike you have, as much as you can
(looking for Torpado Super light frame/fork or for Raleigh International frame fork 58cm)