Chain issue with my "9 Speed" Nishiki
#1
Newbie
Thread Starter
Join Date: Nov 2022
Posts: 25
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 26 Post(s)
Likes: 0
Liked 4 Times
in
4 Posts
Chain issue with my "9 Speed" Nishiki
Hi all.
First, a thank you to everyone on this forum who weighed in on my shifter upgrade from downtube shifters. After considering an upgrade to index shifters, I ended up staying "analog" and going with some dia compe bar end shifters instead. Very happy with them.
On to my current problem.
I have a drivetrain that is effectively a 9 speed at the moment. If I try to go to the large chainring - largest sprocket combination, the chain comes up short, maxing out the derailleur and locking up the chain so tight that I have to take the wheel off to release the tension and reset the drivetrain.
I think I still have the original chain on the bike, so I bought first a 7.3mm 1/2" x 3/32" 116 link chain designated for 5-8 speeds and installed it.
At the 116 link length, the new chain would let me get on to the large chainring - largest sprocket combination, but the chain would then skip-jump when on the two smallest sprockets,
I took out first 2 links (to 114 net links), then 4 links (to 112 links) and the same behavior worked on larger three sprockets, skipped on the smallest two sprockets. Oddly, at 112 links, it would still go onto the large chainring - largest sprocket combination.
I then bought a beefier 7.8mm 116 link chain designated for 5-6 speed use, and I got the same results: skipping-jumping on the lower 2 sprockets, good on the three largest sprockets.
I (think I correctly) measured the legacy chain the with a caliper and came up with 7.96-8.0mm width (at the pin: I got 7.28-7.30 at the pin on the first chain and 7-76-7.80 on the second chain).
I no longer have the original Suntour "Blue" series derailleur, having replaced it with another Suntour derailleur with the same jockey arm (?) length.
So what do you folks think?
Is my drivetrain so old that I need an even beefier single speed chain?
Is my derailleur just tired (it probably has over 10,000 miles on it since installed) and not maintaining sufficient tension in the chain when at its most slack on the smaller sprockets.
I would really like to get over the hump on this 9 speed issue and have my Nishiki fully functioning again, so any insights/ideas would be most appreciated.
First, a thank you to everyone on this forum who weighed in on my shifter upgrade from downtube shifters. After considering an upgrade to index shifters, I ended up staying "analog" and going with some dia compe bar end shifters instead. Very happy with them.
On to my current problem.
I have a drivetrain that is effectively a 9 speed at the moment. If I try to go to the large chainring - largest sprocket combination, the chain comes up short, maxing out the derailleur and locking up the chain so tight that I have to take the wheel off to release the tension and reset the drivetrain.
I think I still have the original chain on the bike, so I bought first a 7.3mm 1/2" x 3/32" 116 link chain designated for 5-8 speeds and installed it.
At the 116 link length, the new chain would let me get on to the large chainring - largest sprocket combination, but the chain would then skip-jump when on the two smallest sprockets,
I took out first 2 links (to 114 net links), then 4 links (to 112 links) and the same behavior worked on larger three sprockets, skipped on the smallest two sprockets. Oddly, at 112 links, it would still go onto the large chainring - largest sprocket combination.
I then bought a beefier 7.8mm 116 link chain designated for 5-6 speed use, and I got the same results: skipping-jumping on the lower 2 sprockets, good on the three largest sprockets.
I (think I correctly) measured the legacy chain the with a caliper and came up with 7.96-8.0mm width (at the pin: I got 7.28-7.30 at the pin on the first chain and 7-76-7.80 on the second chain).
I no longer have the original Suntour "Blue" series derailleur, having replaced it with another Suntour derailleur with the same jockey arm (?) length.
So what do you folks think?
Is my drivetrain so old that I need an even beefier single speed chain?
Is my derailleur just tired (it probably has over 10,000 miles on it since installed) and not maintaining sufficient tension in the chain when at its most slack on the smaller sprockets.
I would really like to get over the hump on this 9 speed issue and have my Nishiki fully functioning again, so any insights/ideas would be most appreciated.
#2
Full Member
Join Date: Sep 2007
Location: PDX
Posts: 423
Mentioned: 2 Post(s)
Tagged: 0 Thread(s)
Quoted: 15 Post(s)
Likes: 0
Liked 46 Times
in
18 Posts
what tooth size are your two chainrings you're running and what's the largest / smallest cog you're using on the cassette? you might need a medium to long cage rear derailleur to shift cleanly depending on the big / small chainring / cog combinations:
#3
The dropped
Join Date: Oct 2018
Location: Columbus, OH
Posts: 2,393
Bikes: Pake C'Mute Touring/Commuter Build, 1989 Kona Cinder Cone, 1995 Trek 5200, 1973 Raleigh Super Course FG, 1960/61 Montgomery Ward Hawthorne "thrift" 3 speed, by Hercules (sold) : 1966 Schwinn Deluxe Racer (sold)
Mentioned: 10 Post(s)
Tagged: 0 Thread(s)
Quoted: 1731 Post(s)
Liked 1,006 Times
in
691 Posts
Hi all.
First, a thank you to everyone on this forum who weighed in on my shifter upgrade from downtube shifters. After considering an upgrade to index shifters, I ended up staying "analog" and going with some dia compe bar end shifters instead. Very happy with them.
On to my current problem.
I have a drivetrain that is effectively a 9 speed at the moment. If I try to go to the large chainring - largest sprocket combination, the chain comes up short, maxing out the derailleur and locking up the chain so tight that I have to take the wheel off to release the tension and reset the drivetrain.
I think I still have the original chain on the bike, so I bought first a 7.3mm 1/2" x 3/32" 116 link chain designated for 5-8 speeds and installed it.
At the 116 link length, the new chain would let me get on to the large chainring - largest sprocket combination, but the chain would then skip-jump when on the two smallest sprockets,
I took out first 2 links (to 114 net links), then 4 links (to 112 links) and the same behavior worked on larger three sprockets, skipped on the smallest two sprockets. Oddly, at 112 links, it would still go onto the large chainring - largest sprocket combination.
I then bought a beefier 7.8mm 116 link chain designated for 5-6 speed use, and I got the same results: skipping-jumping on the lower 2 sprockets, good on the three largest sprockets.
I (think I correctly) measured the legacy chain the with a caliper and came up with 7.96-8.0mm width (at the pin: I got 7.28-7.30 at the pin on the first chain and 7-76-7.80 on the second chain).
I no longer have the original Suntour "Blue" series derailleur, having replaced it with another Suntour derailleur with the same jockey arm (?) length.
So what do you folks think?
Is my drivetrain so old that I need an even beefier single speed chain?
Is my derailleur just tired (it probably has over 10,000 miles on it since installed) and not maintaining sufficient tension in the chain when at its most slack on the smaller sprockets.
I would really like to get over the hump on this 9 speed issue and have my Nishiki fully functioning again, so any insights/ideas would be most appreciated.
First, a thank you to everyone on this forum who weighed in on my shifter upgrade from downtube shifters. After considering an upgrade to index shifters, I ended up staying "analog" and going with some dia compe bar end shifters instead. Very happy with them.
On to my current problem.
I have a drivetrain that is effectively a 9 speed at the moment. If I try to go to the large chainring - largest sprocket combination, the chain comes up short, maxing out the derailleur and locking up the chain so tight that I have to take the wheel off to release the tension and reset the drivetrain.
I think I still have the original chain on the bike, so I bought first a 7.3mm 1/2" x 3/32" 116 link chain designated for 5-8 speeds and installed it.
At the 116 link length, the new chain would let me get on to the large chainring - largest sprocket combination, but the chain would then skip-jump when on the two smallest sprockets,
I took out first 2 links (to 114 net links), then 4 links (to 112 links) and the same behavior worked on larger three sprockets, skipped on the smallest two sprockets. Oddly, at 112 links, it would still go onto the large chainring - largest sprocket combination.
I then bought a beefier 7.8mm 116 link chain designated for 5-6 speed use, and I got the same results: skipping-jumping on the lower 2 sprockets, good on the three largest sprockets.
I (think I correctly) measured the legacy chain the with a caliper and came up with 7.96-8.0mm width (at the pin: I got 7.28-7.30 at the pin on the first chain and 7-76-7.80 on the second chain).
I no longer have the original Suntour "Blue" series derailleur, having replaced it with another Suntour derailleur with the same jockey arm (?) length.
So what do you folks think?
Is my drivetrain so old that I need an even beefier single speed chain?
Is my derailleur just tired (it probably has over 10,000 miles on it since installed) and not maintaining sufficient tension in the chain when at its most slack on the smaller sprockets.
I would really like to get over the hump on this 9 speed issue and have my Nishiki fully functioning again, so any insights/ideas would be most appreciated.
There are lots of ways to size a new chain for your drivetrain, but the simplest is to put the chain over your largest chainring and cog, determine the length, and then add an inch. Tired derailleurs can lose your chosen gear on rough roads, but they wouldn't be the source of skipping.
Last edited by Unca_Sam; 01-27-23 at 01:11 PM.
Likes For Unca_Sam:
#4
I'm good to go!
Join Date: Jul 2017
Location: Mississippi
Posts: 13,773
Bikes: Tarmac Disc Comp Di2 - 2020
Mentioned: 46 Post(s)
Tagged: 0 Thread(s)
Quoted: 5622 Post(s)
Liked 4,287 Times
in
2,951 Posts
I think you need to learn all about the important spec's you need know and consider when choosing a DR or changing the gearing up on a bike. Old or new components, they'll all work properly if you stay inside the spec's.
Know what the min and max cogs size is, max front difference and capacity of your rear DR among other things.
Know what the min and max cogs size is, max front difference and capacity of your rear DR among other things.
#5
Senior Member
Join Date: Feb 2006
Location: Sin City, Nevada
Posts: 2,834
Bikes: Catrike 700, Greenspeed GTO trike, , Linear LWB recumbent, Haluzak Horizon SWB recumbent, Balance 450 MTB, Cannondale SM800 Beast of the East
Mentioned: 18 Post(s)
Tagged: 0 Thread(s)
Quoted: 510 Post(s)
Likes: 0
Liked 218 Times
in
171 Posts
For 9 speed cassettes use a 9 speed chain
You have just verified the need to buy the right chain for your bike. It is determined by the number of gears on the cassette because as the number of gears increases, the width of the tooth is smaller. If you look up chains on eBay, you will see that sellers list 6-8 speeds as one chain and 9 thru 12 each a different chain. Here is what Wikipedia shows for chain width:
- 6 speed – 7.3 mm (9⁄32 in) (Shimano HG), 7.1 mm (9⁄32 in) (SRAM, Shimano IG)
- 7 speed – 7.3 mm (9⁄32 in) (Shimano HG), 7.1 mm (9⁄32 in) (SRAM, Shimano IG)
- 8 speed – 7.3 mm (9⁄32 in) (Shimano HG), 7.1 mm (9⁄32 in) (SRAM, Shimano IG)
- 9 speed – 6.5 to 7.0 mm (1⁄4 to 9⁄32 in) (all brands)
- 10 speed – 6.0 to 7.0 mm (1⁄4 to 9⁄32 in) (Shimano, Campagnolo)
#6
Old fart
Join Date: Nov 2004
Location: Appleton WI
Posts: 24,577
Bikes: Several, mostly not name brands.
Mentioned: 153 Post(s)
Tagged: 0 Thread(s)
Quoted: 3407 Post(s)
Liked 3,010 Times
in
1,729 Posts
Other people have addressed the chain wrap, derailleur capacity, and chain wear concerns, but I feel I ought to clarify this bit:
A single-speed chain, with rare exceptions, will not work on a derailleur-equipped bike. Single-speed chains are 1/8" wide, while derailleur chains are nominally 3/32" wide. Those designed to work on rear clusters with eight or more sprockets are even narrower. A 1/8" wide chain will not be able to seat properly on a cluster designed for 3/32" or narrower chain. When replacing a chain for such a cluster, you need to get one designed to run on the number of sprockets your cluster has. You can generally use a chain designed to run on a higher sprocket count than what you have, but not vice-versa. The higher sprocket count chains tend to be more expensive, so you may as well use the one designed for the exact sprocket count of your cluster.
A single-speed chain, with rare exceptions, will not work on a derailleur-equipped bike. Single-speed chains are 1/8" wide, while derailleur chains are nominally 3/32" wide. Those designed to work on rear clusters with eight or more sprockets are even narrower. A 1/8" wide chain will not be able to seat properly on a cluster designed for 3/32" or narrower chain. When replacing a chain for such a cluster, you need to get one designed to run on the number of sprockets your cluster has. You can generally use a chain designed to run on a higher sprocket count than what you have, but not vice-versa. The higher sprocket count chains tend to be more expensive, so you may as well use the one designed for the exact sprocket count of your cluster.
Last edited by JohnDThompson; 01-27-23 at 01:32 PM.
#7
The dropped
Join Date: Oct 2018
Location: Columbus, OH
Posts: 2,393
Bikes: Pake C'Mute Touring/Commuter Build, 1989 Kona Cinder Cone, 1995 Trek 5200, 1973 Raleigh Super Course FG, 1960/61 Montgomery Ward Hawthorne "thrift" 3 speed, by Hercules (sold) : 1966 Schwinn Deluxe Racer (sold)
Mentioned: 10 Post(s)
Tagged: 0 Thread(s)
Quoted: 1731 Post(s)
Liked 1,006 Times
in
691 Posts
You have just verified the need to buy the right chain for your bike. It is determined by the number of gears on the cassette because as the number of gears increases, the width of the tooth is smaller. If you look up chains on eBay, you will see that sellers list 6-8 speeds as one chain and 9 thru 12 each a different chain. Here is what Wikipedia shows for chain width:
- 6 speed – 7.3 mm (9⁄32 in) (Shimano HG), 7.1 mm (9⁄32 in) (SRAM, Shimano IG)
- 7 speed – 7.3 mm (9⁄32 in) (Shimano HG), 7.1 mm (9⁄32 in) (SRAM, Shimano IG)
- 8 speed – 7.3 mm (9⁄32 in) (Shimano HG), 7.1 mm (9⁄32 in) (SRAM, Shimano IG)
- 9 speed – 6.5 to 7.0 mm (1⁄4 to 9⁄32 in) (all brands)
- 10 speed – 6.0 to 7.0 mm (1⁄4 to 9⁄32 in) (Shimano, Campagnolo)
#8
Senior Member
Join Date: Mar 2007
Location: SF Bay Area, East bay
Posts: 8,356
Bikes: Miyata 618 GT, Marinoni, Kestral 200 2002 Trek 5200, KHS Flite, Koga Miyata, Schwinn Spitfire 5, Mondia Special, Univega Alpina, Miyata team Ti, Santa Cruz Highball
Mentioned: 50 Post(s)
Tagged: 0 Thread(s)
Quoted: 1476 Post(s)
Liked 2,074 Times
in
1,026 Posts
Good chance you bent something trying to shift with the chain too short. I'd start by checking the alignment. You shouldn't have a problem with an 8 speed chain unless you are running a 9 speed cassette, or am I misunderstand your rear gearing? Good pictures always help.
#9
Senior Member
Join Date: Dec 2020
Location: Wake Forest, NC
Posts: 4,461
Bikes: 1989 Cinelli Supercorsa
Mentioned: 10 Post(s)
Tagged: 0 Thread(s)
Quoted: 2671 Post(s)
Liked 2,203 Times
in
1,336 Posts
#10
Newbie
Thread Starter
Join Date: Nov 2022
Posts: 25
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 26 Post(s)
Likes: 0
Liked 4 Times
in
4 Posts
Thanks for all the quick responses.
But boy, did I ever screw up in my subject line.
I have a 5x2 drivetrain (5 sprockets on the cassette, 2 chainrings on the crankset).
I was trying to make light of my 10 speed currently only having nine speeds available, the gearing defined by the large change ring and the largest sprocket being the one speed/gear ratio I can't reach because it runs of of chain.
Didn't think that a "nine speed" could also be a 9 x 1 so my bad for that confusion.
But boy, did I ever screw up in my subject line.
I have a 5x2 drivetrain (5 sprockets on the cassette, 2 chainrings on the crankset).
I was trying to make light of my 10 speed currently only having nine speeds available, the gearing defined by the large change ring and the largest sprocket being the one speed/gear ratio I can't reach because it runs of of chain.
Didn't think that a "nine speed" could also be a 9 x 1 so my bad for that confusion.
Likes For austinbikebill:
#12
Senior Member
Join Date: Feb 2006
Location: Sin City, Nevada
Posts: 2,834
Bikes: Catrike 700, Greenspeed GTO trike, , Linear LWB recumbent, Haluzak Horizon SWB recumbent, Balance 450 MTB, Cannondale SM800 Beast of the East
Mentioned: 18 Post(s)
Tagged: 0 Thread(s)
Quoted: 510 Post(s)
Likes: 0
Liked 218 Times
in
171 Posts
I owned a Nishiki Semi Pro 10 speed (2 X 5) a long time ago. If this is a similar vintage bike (mid 1970s) it has a freewheel, not a cassette. If this is the original freewheel with 10K miles on it, then it is probably worn enough that putting on a brand new chain may result in problems with gear changes like skipping. When I get a chain with this many miles on it I always add a new cassette at the same time. You can still find 5 speed freewheels online but you will also need a compatible freewheel remover to get the old one off. Most long time bike shops may still have the tool and can remove it for a small fee. You don't need the tool to get the new one on - it just spins into place. Sunrace makes a 5 speed freewheel you can get on eBay for $17 delivered and it is in the usual 14 to 28 tooth configuration likely to be what came on the bike new. https://www.ebay.com/itm/303797928556
#13
I'm good to go!
Join Date: Jul 2017
Location: Mississippi
Posts: 13,773
Bikes: Tarmac Disc Comp Di2 - 2020
Mentioned: 46 Post(s)
Tagged: 0 Thread(s)
Quoted: 5622 Post(s)
Liked 4,287 Times
in
2,951 Posts
I have a 5x2 drivetrain (5 sprockets on the cassette, 2 chainrings on the crankset).
I was trying to make light of my 10 speed currently only having nine speeds available, the gearing defined by the large change ring and the largest sprocket being the one speed/gear ratio I can't reach because it runs of of chain.
Didn't think that a "nine speed" could also be a 9 x 1 so my bad for that confusion.
I was trying to make light of my 10 speed currently only having nine speeds available, the gearing defined by the large change ring and the largest sprocket being the one speed/gear ratio I can't reach because it runs of of chain.
Didn't think that a "nine speed" could also be a 9 x 1 so my bad for that confusion.
#14
señor miembro
Join Date: Dec 2018
Location: Pac NW
Posts: 8,094
Bikes: '70s - '80s Campagnolo
Mentioned: 88 Post(s)
Tagged: 0 Thread(s)
Quoted: 3502 Post(s)
Liked 5,630 Times
in
2,826 Posts
Also note that the old school 2x5 gearing were always called "10-speeds," not because they provided 10 different gear combinations, but because consumers didn't know any better. They only really offer 8 gear combinations. You are not supposed to use the large/large and small/small combinations.
But taking this a bit further, they don't even offer 8 gears, because at least 1 or maybe 2 of those 8 gears overlap in their effective gear ratio. So, the old school "10-speed" is really one with 6 or 7 available gears.
And if you ask all the incredibly knowledgeable guys over in the c&v subforum, that's usually enough. And it's been enough for decades. Because it works.
For further reading, see Sheldon Brown's article on cross chaining.
#15
Newbie
Thread Starter
Join Date: Nov 2022
Posts: 25
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 26 Post(s)
Likes: 0
Liked 4 Times
in
4 Posts
you're right, it a freeweheel, not a cessette: I get those two mixed up all the time.
My sprockets range from 14 to 33 teeth.
My chain rings are 36 and 52 teeth.
My sprockets range from 14 to 33 teeth.
My chain rings are 36 and 52 teeth.
#16
Senior Member
Join Date: Feb 2006
Location: Sin City, Nevada
Posts: 2,834
Bikes: Catrike 700, Greenspeed GTO trike, , Linear LWB recumbent, Haluzak Horizon SWB recumbent, Balance 450 MTB, Cannondale SM800 Beast of the East
Mentioned: 18 Post(s)
Tagged: 0 Thread(s)
Quoted: 510 Post(s)
Likes: 0
Liked 218 Times
in
171 Posts
Count again the number of teeth in the inner gear on the freewheel to verify the number of teeth. I don't remember an odd number of teeth for that one. It's usually even such as 28, 30. 32 and 34. Suntour obviously did make a 14-34, 5 speed freewheel because you can find used examples for sale for $$$$ on eBay (https://www.ebay.com/itm/255757832564). If you can live with a reduced gear range it makes sense to go with 14-28 because it is the only brand new one that sells for a reasonable price.
#17
Newbie
Thread Starter
Join Date: Nov 2022
Posts: 25
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 26 Post(s)
Likes: 0
Liked 4 Times
in
4 Posts
I really like that 32 (34?) creeper-gear sprocket. But it is a suntour freewheel based on the tool I need to remove it.
When you're touring with 15-25lbs of gear on a 20 mile 10% grade, that ratio sure comes in handy.
When you're touring with 15-25lbs of gear on a 20 mile 10% grade, that ratio sure comes in handy.
#18
The dropped
Join Date: Oct 2018
Location: Columbus, OH
Posts: 2,393
Bikes: Pake C'Mute Touring/Commuter Build, 1989 Kona Cinder Cone, 1995 Trek 5200, 1973 Raleigh Super Course FG, 1960/61 Montgomery Ward Hawthorne "thrift" 3 speed, by Hercules (sold) : 1966 Schwinn Deluxe Racer (sold)
Mentioned: 10 Post(s)
Tagged: 0 Thread(s)
Quoted: 1731 Post(s)
Liked 1,006 Times
in
691 Posts
It would be easiest to pay the price for a 5 speed freewheel with expanded gear range. Otherwise you're talking about respacing or replacing the rear wheel and respacing the rear triangle to use 126mm spacing to fit modern kids bike 6 and 7 speed freewheels in there. You'd have no issues with the shifters, but you might need a new rear derailleur for it to work well.
#19
Senior Member
Join Date: Feb 2006
Location: Sin City, Nevada
Posts: 2,834
Bikes: Catrike 700, Greenspeed GTO trike, , Linear LWB recumbent, Haluzak Horizon SWB recumbent, Balance 450 MTB, Cannondale SM800 Beast of the East
Mentioned: 18 Post(s)
Tagged: 0 Thread(s)
Quoted: 510 Post(s)
Likes: 0
Liked 218 Times
in
171 Posts
Any possibility you could switch to an 6 speed freewheel? It would be a tight squeeze but maybe a possibility. Shimano currently makes the Tourney model in a 14-34 6 speed freewheel. You might have to buy it on eBay from China to get a reasonable price. Tourney is a fairly low end product but most of these are used on new entry level bikes so that's what is out there. It looks like the difference may be as little as 6 mm with 6 and 7 speeds the same for road bikes according to the Sheldon Brown website. https://www.sheldonbrown.com/cribsheet-spacing.html