Tenacious stem
#1
Newbie
Thread Starter
Join Date: Sep 2014
Location: London, UK
Posts: 53
Bikes: Raleigh, Hercules
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 24 Post(s)
Likes: 0
Liked 9 Times
in
4 Posts
Tenacious stem
Hi
I have a tenacious stem which refuse to leave its hole.
It moves, up and down, turns right or left, but refuses to come out.
I tried gentle, I tried some force.
Nothing.
Any ideas?
Thanks
I have a tenacious stem which refuse to leave its hole.
It moves, up and down, turns right or left, but refuses to come out.
I tried gentle, I tried some force.
Nothing.
Any ideas?
Thanks
Likes For jethin:
#3
Senior Member
Join Date: Aug 2009
Location: Berkeley, CA
Posts: 7,238
Bikes: '72 Cilo Pacer, '72 Gitane Gran Tourisme, '72 Peugeot PX10, '73 Speedwell Ti, '74 Peugeot UE-8, '75 Peugeot PR-10L, '80 Colnago Super, '85 De Rosa Pro, '86 Look Equipe 753, '86 Look KG86, '89 Parkpre Team, '90 Parkpre Team MTB, '90 Merlin
Mentioned: 87 Post(s)
Tagged: 0 Thread(s)
Quoted: 830 Post(s)
Liked 2,122 Times
in
554 Posts
How far up does it go? Could it be the wedge is catching on the headset locknut? Maybe tighten the stem bolt a little (but not too tight to move) so the wedge nut stays in line with stem shaft, or try unscrewing the headset locknut?
Likes For gaucho777:
#4
Newbie
Thread Starter
Join Date: Sep 2014
Location: London, UK
Posts: 53
Bikes: Raleigh, Hercules
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 24 Post(s)
Likes: 0
Liked 9 Times
in
4 Posts
It's an extra long stem. It goes all the way in. The nut must be 40cm long. Most of it comes out.
I've removed the wedge nut. No change.
I've removed the headset locknut. Removed all bearings for access. No change.
It could be as you said the wedge catching on something but can't see what.
I've removed the wedge nut. No change.
I've removed the headset locknut. Removed all bearings for access. No change.
It could be as you said the wedge catching on something but can't see what.
Last edited by ConnoisseurEqua; 09-19-22 at 08:29 PM.
#5
Senior Member
Join Date: Sep 2005
Location: Oakland, CA
Posts: 3,265
Bikes: '82 Univega Competizione, '72 Motobecane Grand Record, '83 Mercian KOM Touring, '85 Univega Alpina Uno, '76 Eisentraut Limited
Mentioned: 57 Post(s)
Tagged: 0 Thread(s)
Quoted: 1088 Post(s)
Liked 1,205 Times
in
701 Posts
Could you post a couple of pics? I’m stumped. Maybe head badge rivets?
#6
Senior Member
Join Date: Nov 2004
Posts: 23,223
Mentioned: 654 Post(s)
Tagged: 1 Thread(s)
Quoted: 4722 Post(s)
Likes: 0
Liked 3,036 Times
in
1,874 Posts
Based on the title, I was expecting to see a photo of the mega-rare Phil Wood handlebar stem.
Seriously though, it seems strange that the stem comes most of the way out, then stops.
Seriously though, it seems strange that the stem comes most of the way out, then stops.
Likes For T-Mar:
#7
Senior Member
Join Date: Dec 2020
Location: Wake Forest, NC
Posts: 5,774
Bikes: 1989 Cinelli Supercorsa
Mentioned: 11 Post(s)
Tagged: 0 Thread(s)
Quoted: 3502 Post(s)
Liked 2,916 Times
in
1,770 Posts
#8
Senior Member
Join Date: Jan 2013
Posts: 2,678
Bikes: too many sparkly Italians, some sweet Americans and a couple interesting Japanese
Mentioned: 10 Post(s)
Tagged: 0 Thread(s)
Quoted: 569 Post(s)
Liked 580 Times
in
408 Posts
It's an extra long stem. It goes all the way in. The nut must be 40cm long. Most of it comes out.
I've removed the wedge nut. No change.
I've removed the headset locknut. Removed all bearings for access. No change.
It could be as you said the wedge catching on something but can't see what.
I've removed the wedge nut. No change.
I've removed the headset locknut. Removed all bearings for access. No change.
It could be as you said the wedge catching on something but can't see what.
#10
Newbie
Thread Starter
Join Date: Sep 2014
Location: London, UK
Posts: 53
Bikes: Raleigh, Hercules
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 24 Post(s)
Likes: 0
Liked 9 Times
in
4 Posts
This is the stem I'm trying to remove.
I cannot find them anymore so it has to come out.
I will take pics of the stem with everything removed.
I cannot find them anymore so it has to come out.
I will take pics of the stem with everything removed.
#11
Senior Member
Join Date: Jun 2008
Location: Louisville, KY
Posts: 13,444
Mentioned: 33 Post(s)
Tagged: 0 Thread(s)
Quoted: 4230 Post(s)
Liked 2,947 Times
in
1,806 Posts
Likes For RustyJames:
Likes For tricky:
#15
Senior Member
Join Date: Sep 2005
Location: Oakland, CA
Posts: 3,265
Bikes: '82 Univega Competizione, '72 Motobecane Grand Record, '83 Mercian KOM Touring, '85 Univega Alpina Uno, '76 Eisentraut Limited
Mentioned: 57 Post(s)
Tagged: 0 Thread(s)
Quoted: 1088 Post(s)
Liked 1,205 Times
in
701 Posts
It looks like this type of Humpert stem (taller than the one in the pic I’m posting, which comes from evilbay). Looks like a traditional wedge, no surprises. Yes, if you have not disconnected the cables yet, I agree that this is likely the cause, since you’re able to get all kinds of movement.
#17
Newbie
Thread Starter
Join Date: Sep 2014
Location: London, UK
Posts: 53
Bikes: Raleigh, Hercules
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 24 Post(s)
Likes: 0
Liked 9 Times
in
4 Posts
As one can see all cables removed. Nothing should stop it to come out.
As I mentioned earlier, it moves free, not without effort though.
As I mentioned earlier, it moves free, not without effort though.
Likes For ConnoisseurEqua:
#18
small ring
Join Date: Jul 2012
Location: PNW
Posts: 1,024
Mentioned: 24 Post(s)
Tagged: 0 Thread(s)
Quoted: 437 Post(s)
Liked 925 Times
in
370 Posts
If you put the bolt back in, does it drop down all the way?
__________________
59 Allegro Special -- 72 Bob Jackson -- 74 Motobecane Grand Jubile -- 74 Sekine SHS 271 -- 80 Nishiki International
85 Shogun 800 -- 86 Tommasini Super Prestige -- 92 Specialized Rockhopper -- 17 Colnago Arabesque
59 Allegro Special -- 72 Bob Jackson -- 74 Motobecane Grand Jubile -- 74 Sekine SHS 271 -- 80 Nishiki International
85 Shogun 800 -- 86 Tommasini Super Prestige -- 92 Specialized Rockhopper -- 17 Colnago Arabesque
#19
Senior Member
Join Date: Oct 2005
Location: Upper Left, USA
Posts: 1,915
Mentioned: 50 Post(s)
Tagged: 0 Thread(s)
Quoted: 634 Post(s)
Liked 444 Times
in
298 Posts
When you thread the bolt in, are you able to tell if the wedge is loose? If not, smack the bolt with a hammer (with some wood inbetween if you want to keep the bolt looking nice) to get it fully loose. It might be stuck to the bottom of the stem just enough to be keeping the stem locked in the steerer.
#20
Senior Member
Join Date: Dec 2020
Location: Wake Forest, NC
Posts: 5,774
Bikes: 1989 Cinelli Supercorsa
Mentioned: 11 Post(s)
Tagged: 0 Thread(s)
Quoted: 3502 Post(s)
Liked 2,916 Times
in
1,770 Posts
For me, this would be the time to man-handle that thing out.
Likes For smd4:
#21
Newbie
Thread Starter
Join Date: Sep 2014
Location: London, UK
Posts: 53
Bikes: Raleigh, Hercules
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 24 Post(s)
Likes: 0
Liked 9 Times
in
4 Posts
I applied WD-40 on both side. The rust is the WD-40 with some rust dust.
I will try to bold it in again and use my rubber mallet. But I don't recall hearing the bottom of the stem moving freely.
I will try to bold it in again and use my rubber mallet. But I don't recall hearing the bottom of the stem moving freely.
#22
Senior Member
Join Date: Mar 2021
Location: Beaverton, OR
Posts: 1,433
Bikes: You had me at rusty and Italian!!
Mentioned: 31 Post(s)
Tagged: 0 Thread(s)
Quoted: 566 Post(s)
Liked 1,047 Times
in
542 Posts
If aesthetics aren’t paramount, lots of WD-40 and spin and pull. I’m leaning towards rust on the stem or inside the steerer tube holding things up.
#23
Senior Member
Join Date: Aug 2017
Location: Germany
Posts: 1,090
Bikes: 80s Alan Super Record, 79' Somec Special, 90s Rossin(?) Columbus Ego Triathlon, previously: Bianchi SBX Reparto Corse (stolen) and so on...
Mentioned: 16 Post(s)
Tagged: 0 Thread(s)
Quoted: 391 Post(s)
Liked 812 Times
in
602 Posts
I thought 40cm was a typo...
#24
Senior Member
Join Date: May 2012
Location: Point Reyes Station, California
Posts: 4,526
Bikes: Indeed!
Mentioned: 92 Post(s)
Tagged: 0 Thread(s)
Quoted: 1506 Post(s)
Liked 3,469 Times
in
1,131 Posts
...When you thread the bolt in, are you able to tell if the wedge is loose? If not, smack the bolt with a hammer (with some wood inbetween if you want to keep the bolt looking nice) to get it fully loose. It might be stuck to the bottom of the stem just enough to be keeping the stem locked in the steerer.
At this point you should thread the bolt back into the wedge a few turns and then smack it with a hammer to loosen the wedge. Your rubber mallet may not work, but a dead-blow hammer or a steel hammer should do the job. As mentioned above you can protect the finish on the bolt head with a piece of lumber between the hammer and the bolt.
Brent
Likes For obrentharris:
#25
Senior Member
Join Date: Jan 2004
Location: Madison, WI USA
Posts: 6,153
Mentioned: 50 Post(s)
Tagged: 0 Thread(s)
Quoted: 2362 Post(s)
Liked 1,749 Times
in
1,191 Posts
Wait, I thought the wedge was already out of the equation, based on post # 4. But now it's sounding more like a garden-variety broken stem. If the wedge has NOT been removed (well, "released" would be more accurate, I suppose), and is still engaged with the bolt, AND the stem proper is broken in two pieces below what we can see, you'll experience just what you're describing. The bottom bit of the broken stem will "affiliate" with the wedge and not want to turn or come out, even while you're lifting and wrestling with the rest of the stem. It's happened to me, but only with aluminum stems, never with steel. That said, never say never....
Try this - Pull upward gently on the stem, and continue turning the bolt counter-clockwise. That upward pressure should (well, might) hold the broken bit / wedge from rotating, and you might eventually get the bolt to unthread entirely from the wedge, releasing it, and the busted bit of stem, to fall into the steerer. Then the main part of the stem should just pull out, and you should be able to flip the bike over and the rest will drop out.
If that's not it, you might also shed some light on your situation by looking from underneath; you may even want to remove the brake bolt, just for a better visual sense of what's going on.
Try this - Pull upward gently on the stem, and continue turning the bolt counter-clockwise. That upward pressure should (well, might) hold the broken bit / wedge from rotating, and you might eventually get the bolt to unthread entirely from the wedge, releasing it, and the busted bit of stem, to fall into the steerer. Then the main part of the stem should just pull out, and you should be able to flip the bike over and the rest will drop out.
If that's not it, you might also shed some light on your situation by looking from underneath; you may even want to remove the brake bolt, just for a better visual sense of what's going on.