22.0 mm quill in a 22.2 mm steerer?
#1
Newbie
Thread Starter
22.0 mm quill in a 22.2 mm steerer?
I recently received the quill stem adapter I ordered from Amazon and when installing it, found it went into the steerer really easily. Too easily actually, so I measured the quill and despite the Amazon ad listing it as a 22.2 mm quill, it measures 22.0 mm. Can I still use this or is it unsafe? It's a quill stem adapter with a wedge so if the wedge is sufficiently tight, what problems could arise?
#2
It's MY mountain
Join Date: Sep 2006
Location: Mt.Diablo
Posts: 10,002
Bikes: Klein, Merckx, Trek
Mentioned: 70 Post(s)
Tagged: 0 Thread(s)
Quoted: 4338 Post(s)
Liked 2,980 Times
in
1,617 Posts
There will be a little gap there (between stem and headset) and there'll be some play, but it'll be safe.
#3
Really Old Senior Member
.2mm is only .008"
#4
Senior Member
Join Date: Feb 2012
Location: Rochester, NY
Posts: 18,073
Bikes: Stewart S&S coupled sport tourer, Stewart Sunday light, Stewart Commuting, Stewart Touring, Co Motion Tandem, Stewart 3-Spd, Stewart Track, Fuji Finest, Mongoose Tomac ATB, GT Bravado ATB, JCP Folder, Stewart 650B ATB
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 4201 Post(s)
Liked 3,857 Times
in
2,305 Posts
The clearance between the steerer ID and the stem quill's OD is not written in stone. Millions of cheap American bikes with a stamped and wrapped stem (think Wald) have a fit into the steerer that can be rather loose. Typically the usual concerns are keeping the wedge tight, UNLESS the rider is challenging the bike. Jumps, lots of strong upper body efforts and the classic lack of maintenance.
Of course any stem adapter or extender should be routinely checked for a secure grip on the steerer and stem and not be used for trick, competitive riding or stunts. Andy
Of course any stem adapter or extender should be routinely checked for a secure grip on the steerer and stem and not be used for trick, competitive riding or stunts. Andy
__________________
AndrewRStewart
AndrewRStewart
Likes For Andrew R Stewart:
#5
Senior Member
Join Date: Jul 2005
Location: Boulder County, CO
Posts: 4,393
Bikes: '80 Masi Gran Criterium, '12 Trek Madone, early '60s Frejus track
Mentioned: 6 Post(s)
Tagged: 0 Thread(s)
Quoted: 513 Post(s)
Liked 448 Times
in
337 Posts
If the bottom wedge directly contacts the steerer like one of these,
0.2 mm should be no problem. If it's the spreader kind, like this
there might be a problem.
0.2 mm should be no problem. If it's the spreader kind, like this
there might be a problem.
Likes For oldbobcat:
#6
Senior Member
Join Date: Sep 2010
Location: Roswell, GA
Posts: 8,319
Bikes: '93 Trek 750, '92 Schwinn Crisscross, '93 Mongoose Alta
Mentioned: 30 Post(s)
Tagged: 0 Thread(s)
Quoted: 1438 Post(s)
Liked 1,092 Times
in
723 Posts
Don't forget to grease the stem, wedge and bolt so they don't seize up over time.
Likes For dsbrantjr:
#7
Senior Member
If it makes you feel any better, I have a Nitto quill stem sitting here off an old Cannondale that measures 22.0mm (at spots, depends on the paint thickness, other places it is 22.1mm). I imagine that if I scraped off all the paint it would be even less than 22mm in some areas. It's part of why quill stems (can) creak.
#8
Senior Member
Join Date: Feb 2017
Location: Northern Shenandoah Valley
Posts: 4,141
Bikes: More bikes than riders
Mentioned: 36 Post(s)
Tagged: 0 Thread(s)
Quoted: 1446 Post(s)
Liked 762 Times
in
570 Posts
Similar question: if a guy had access to a 21.1mm quill stem with the triangular type wedge...could he use that in a French steerer (22mm)? I have a French bike with a sanded-down 22.2mm quill stem, but I don't like how tight it is and have access to a 21.1mm stem that will work nicely if it'll be safe to use. If not by itself...maybe with some beer can shimming?