Air Chuck for Presta Valves
#1
Full Member
Thread Starter
Air Chuck for Presta Valves
Can anyone point me to where I can buy a simple air chuck for Presta valves similar to the one pictured here that's used for Shrader valves?
Likes For cloud:
#3
bOsscO
Join Date: May 2006
Location: Vancouver
Posts: 746
Bikes: 2024 Spec Crux, 2015 Norco Search S1, 93 Mongoose IBOC COMP
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 296 Post(s)
Liked 355 Times
in
212 Posts
Or buy the little brass adaptor (most LBS's should have them) for $1 and use your regular gauge/chuck.
Likes For bOsscO:
#4
Senior Member
Join Date: Sep 2006
Location: Paradise, TX
Posts: 2,087
Bikes: Soma Pescadero, Surly Pugsley, Salsa Fargo, Schwinn Klunker, Gravity SS 27.5, Monocog 29er
Mentioned: 1 Post(s)
Tagged: 0 Thread(s)
Quoted: 186 Post(s)
Liked 234 Times
in
166 Posts
For general inflation or just to seat tubeless beads? I remove the presta core and inflate with the shrader head to seat the beads. Then allow it to air back down, insert sealant and inflate to proper pressure with a pump.
#5
Senior Member
Join Date: Oct 2013
Location: Mich
Posts: 7,386
Bikes: RSO E-tire dropper fixie brifter
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 6 Post(s)
Liked 2,968 Times
in
1,917 Posts
simple answer, no. Cheaper to spend an extra minute screwing on the adapter & using the car valve inflator. I've looked for a simple economical solution & nothing was available that made logical sense.
__________________
-Oh Hey!
-Oh Hey!
#6
On Your Left
Join Date: Nov 2011
Location: Long Island, New York, USA
Posts: 8,373
Bikes: Trek Emonda SLR, Sram eTap, Zipp 303
Mentioned: 34 Post(s)
Tagged: 0 Thread(s)
Quoted: 3004 Post(s)
Liked 2,433 Times
in
1,187 Posts
Be carefull that you compressor doesn't burst your tube.
#7
Mad bike riding scientist
Join Date: Nov 2004
Location: Denver, CO
Posts: 27,362
Bikes: Some silver ones, a red one, a black and orange one, and a few titanium ones
Mentioned: 152 Post(s)
Tagged: 1 Thread(s)
Quoted: 6219 Post(s)
Liked 4,218 Times
in
2,365 Posts
The SKS Presta adapter is a very good choice. It’s far cheaper than a Silca chuck ($8 vs >$35) and it works with a Schrader compressor head. We use them at my co-op all the time. You don’t even have to order them on line if you don’t want to. Quality Bicycle Products carries them and your local shop can order them.
__________________
Stuart Black
Plan Epsilon Around Lake Michigan in the era of Covid
Old School…When It Wasn’t Ancient bikepacking
Gold Fever Three days of dirt in Colorado
Pokin' around the Poconos A cold ride around Lake Erie
Dinosaurs in Colorado A mountain bike guide to the Purgatory Canyon dinosaur trackway
Solo Without Pie. The search for pie in the Midwest.
Picking the Scablands. Washington and Oregon, 2005. Pie and spiders on the Columbia River!
Stuart Black
Plan Epsilon Around Lake Michigan in the era of Covid
Old School…When It Wasn’t Ancient bikepacking
Gold Fever Three days of dirt in Colorado
Pokin' around the Poconos A cold ride around Lake Erie
Dinosaurs in Colorado A mountain bike guide to the Purgatory Canyon dinosaur trackway
Solo Without Pie. The search for pie in the Midwest.
Picking the Scablands. Washington and Oregon, 2005. Pie and spiders on the Columbia River!
#8
Newbie
Join Date: Sep 2020
Posts: 4
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 0 Post(s)
Likes: 0
Liked 1 Time
in
1 Post
I’ve used prestaflate (one without the gauge) for the last few years. I only use it for seating tubeless mtb tires and finding holes in tubes to patch. Easily the best $35 I’ve ever spent. No issues seating any Mtb tires far better than the adapters.
#9
Full Member
Thread Starter
Thanks for all the great suggestions. Among them, I will find the solution best for me.
#10
Senior Member
Join Date: Feb 2004
Location: St Peters, Missouri
Posts: 30,225
Bikes: Catrike 559 I own some others but they don't get ridden very much.
Mentioned: 16 Post(s)
Tagged: 0 Thread(s)
Quoted: 1572 Post(s)
Liked 643 Times
in
364 Posts
I recently made the decision to convert to Schrader valves over this winter for that very reason.
__________________
My greatest fear is all of my kids standing around my coffin and talking about "how sensible" dad was.
My greatest fear is all of my kids standing around my coffin and talking about "how sensible" dad was.
Likes For Retro Grouch:
#12
Senior Member
Join Date: Jun 2002
Location: Montreal, Quebec
Posts: 5,925
Mentioned: 16 Post(s)
Tagged: 0 Thread(s)
Quoted: 1819 Post(s)
Liked 1,693 Times
in
974 Posts
Cyclus tube inflator:
https://www.bike24.com/p2277205.html
https://www.bike24.com/p2277205.html
#13
Senior Member
Join Date: Oct 2013
Location: Mich
Posts: 7,386
Bikes: RSO E-tire dropper fixie brifter
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 6 Post(s)
Liked 2,968 Times
in
1,917 Posts
Cyclus tube inflator:
https://www.bike24.com/p2277205.html
https://www.bike24.com/p2277205.html
who the retailer for that in the USA?
__________________
-Oh Hey!
-Oh Hey!
#16
Newbie
Join Date: Aug 2020
Posts: 55
Bikes: 1986 Cannondale SR600
Mentioned: 2 Post(s)
Tagged: 0 Thread(s)
Quoted: 20 Post(s)
Likes: 0
Liked 7 Times
in
6 Posts
A moot point for me though: this was only an issue 30 years ago until I chopped the schrader head off my floor pump and put a Silca 24.4 chuck in its place.
#17
bOsscO
Join Date: May 2006
Location: Vancouver
Posts: 746
Bikes: 2024 Spec Crux, 2015 Norco Search S1, 93 Mongoose IBOC COMP
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 296 Post(s)
Liked 355 Times
in
212 Posts
I see these all the time, but have never, ever, been satisfied with any that I've tried. They always leak on me! I don't know whether people just accept the leaking, or if all the ones I've tried have been inferior quality, but then I haven't seen anything to distinguish better quality ones.
I generally only use them to inflate the tire and take it off (and screw down the Presta valve closed) when I reach the desired pressure.
Likes For bOsscO:
#18
Newbie
Join Date: Aug 2020
Posts: 55
Bikes: 1986 Cannondale SR600
Mentioned: 2 Post(s)
Tagged: 0 Thread(s)
Quoted: 20 Post(s)
Likes: 0
Liked 7 Times
in
6 Posts
If I did want to switch over to a Schrader interface for inflating, I'd be tempted to get removeable-core presta tubes and a pair of ConvertAir valve converters and just leave them installed.
ConvertAir converters
Last edited by luns; 10-09-20 at 11:41 PM.
#19
Senior Member
The easy answer is to drill out the valve opening in your rim from 0.25” to 0.3125” (5/16”) and use a tube with a Schrader valve. Continental makes such tubes and they are they type with the threaded stem. Problem solved.
#20
Full Member
Thread Starter
They've all leaked for me while inflating. This makes any pressure gauge on a floor pump much less useful as you can only guess what pressure you've reached since the gauge doesn't hang around at tire pressure. All the extra pumping is also a pain, though I suppose if you were using a compressor, the lost air is less of a problem.
If I did want to switch over to a Schrader interface for inflating, I'd be tempted to get removeable-core presta tubes and a pair of ConvertAir valve converters and just leave them installed.
ConvertAir converters
If I did want to switch over to a Schrader interface for inflating, I'd be tempted to get removeable-core presta tubes and a pair of ConvertAir valve converters and just leave them installed.
ConvertAir converters
Last edited by oldwinger14; 10-12-20 at 08:50 AM.
#21
Mad bike riding scientist
Join Date: Nov 2004
Location: Denver, CO
Posts: 27,362
Bikes: Some silver ones, a red one, a black and orange one, and a few titanium ones
Mentioned: 152 Post(s)
Tagged: 1 Thread(s)
Quoted: 6219 Post(s)
Liked 4,218 Times
in
2,365 Posts
Why not just use Schrader valves if you have issues with Presta valves? Presta valves are extremely simple and easy to use if you use the proper chuck.
__________________
Stuart Black
Plan Epsilon Around Lake Michigan in the era of Covid
Old School…When It Wasn’t Ancient bikepacking
Gold Fever Three days of dirt in Colorado
Pokin' around the Poconos A cold ride around Lake Erie
Dinosaurs in Colorado A mountain bike guide to the Purgatory Canyon dinosaur trackway
Solo Without Pie. The search for pie in the Midwest.
Picking the Scablands. Washington and Oregon, 2005. Pie and spiders on the Columbia River!
Stuart Black
Plan Epsilon Around Lake Michigan in the era of Covid
Old School…When It Wasn’t Ancient bikepacking
Gold Fever Three days of dirt in Colorado
Pokin' around the Poconos A cold ride around Lake Erie
Dinosaurs in Colorado A mountain bike guide to the Purgatory Canyon dinosaur trackway
Solo Without Pie. The search for pie in the Midwest.
Picking the Scablands. Washington and Oregon, 2005. Pie and spiders on the Columbia River!
#22
Full Member
Thread Starter
I do not have any issues with Presta valves for everyday use. I was looking for a solution that would allow me to use my air compressor when trying to seat new tubeless tires. The air compressor hose has a Shrader fitting at the end and I needed an adapter of some sort so that I could use the air compressor on my Presta valves. Silca, Prestacycle and others have various types of adapters, but these ConvertAir look like a good solution. If I like them I may keep them installed to make injecting sealant as needed an easier task than trying to inject thru a Presta fitting.
#23
Mad bike riding scientist
Join Date: Nov 2004
Location: Denver, CO
Posts: 27,362
Bikes: Some silver ones, a red one, a black and orange one, and a few titanium ones
Mentioned: 152 Post(s)
Tagged: 1 Thread(s)
Quoted: 6219 Post(s)
Liked 4,218 Times
in
2,365 Posts
I do not have any issues with Presta valves for everyday use. I was looking for a solution that would allow me to use my air compressor when trying to seat new tubeless tires. The air compressor hose has a Shrader fitting at the end and I needed an adapter of some sort so that I could use the air compressor on my Presta valves. Silca, Prestacycle and others have various types of adapters, but these ConvertAir look like a good solution. If I like them I may keep them installed to make injecting sealant as needed an easier task than trying to inject thru a Presta fitting.
__________________
Stuart Black
Plan Epsilon Around Lake Michigan in the era of Covid
Old School…When It Wasn’t Ancient bikepacking
Gold Fever Three days of dirt in Colorado
Pokin' around the Poconos A cold ride around Lake Erie
Dinosaurs in Colorado A mountain bike guide to the Purgatory Canyon dinosaur trackway
Solo Without Pie. The search for pie in the Midwest.
Picking the Scablands. Washington and Oregon, 2005. Pie and spiders on the Columbia River!
Stuart Black
Plan Epsilon Around Lake Michigan in the era of Covid
Old School…When It Wasn’t Ancient bikepacking
Gold Fever Three days of dirt in Colorado
Pokin' around the Poconos A cold ride around Lake Erie
Dinosaurs in Colorado A mountain bike guide to the Purgatory Canyon dinosaur trackway
Solo Without Pie. The search for pie in the Midwest.
Picking the Scablands. Washington and Oregon, 2005. Pie and spiders on the Columbia River!
#24
Full Member
Thread Starter
Whatever floats your boat but if you are going to leave them in place, why not just drill out the rim and use Schrader valves? Schrader valves are made for tubeless so you wouldn’t have to fiddle with adaptors. Schrader tubeless valves cost only a little more than the ConvertAirs.
Likes For oldwinger14:
#25
Senior Member
Join Date: Oct 2005
Posts: 1,174
Mentioned: 3 Post(s)
Tagged: 0 Thread(s)
Quoted: 381 Post(s)
Liked 145 Times
in
93 Posts
I prefer not to drill the wheels to go 100% Shrader. If I did that, there’s no returning to Presta nor do I want to abandon Presta valves completely. As I mentioned earlier, I would most likely only use the Convert Air adapters to make it easier to seat new tubeless tires.
https://www.amazon.com/Quad-Wheels-M...dp/B000AO5ICG/