Go Back  Bike Forums > Bike Forums > Classic & Vintage
Reload this Page >

Campagnolo 2-bolt seatpost - bolt dimensions?

Notices
Classic & Vintage This forum is to discuss the many aspects of classic and vintage bicycles, including musclebikes, lightweights, middleweights, hi-wheelers, bone-shakers, safety bikes and much more.

Campagnolo 2-bolt seatpost - bolt dimensions?

Old 02-12-22, 12:34 PM
  #1  
cyclic_eric
Full Member
Thread Starter
 
cyclic_eric's Avatar
 
Join Date: Jan 2013
Location: Oakland CA
Posts: 274

Bikes: 1984 Gitane TdF, 1986 Look Équipe, 1983 Colnago Super

Mentioned: 2 Post(s)
Tagged: 0 Thread(s)
Quoted: 112 Post(s)
Liked 132 Times in 79 Posts
Campagnolo 2-bolt seatpost - bolt dimensions?

I just purchased the Campagnolo 2-bolt seatpost pictured below. It should arrive in about a week. Does anyone know the dimensions of the 2 bolts? My guess is they are M8 x 1.25mm, perhaps 30 - 40 mm long. If you happen to have such a post sitting around on your workbench, please let me know. Thanks in-advance.

I ask because all my current saddles have an open slot running down the middle. So I'm thinking of replacing the bolts with hex (Allen) head screws, and adjusting from above. I want to have a few screws on hand when my new seatpost is delivered. Otherwise I'll have to heat & bend an old wrench, or buy an expensive Campy wrench to fit.

In the mail...



Expensive plan B:
cyclic_eric is offline  
Old 02-12-22, 12:44 PM
  #2  
Andy_K 
Senior Member
 
Andy_K's Avatar
 
Join Date: Jan 2008
Location: Beaverton, OR
Posts: 14,787

Bikes: Yes

Mentioned: 522 Post(s)
Tagged: 0 Thread(s)
Quoted: 3228 Post(s)
Liked 3,853 Times in 1,436 Posts
Most of the bikes I use Campy two bolt seatposts on have modern plastic saddles and a standard 10mm wrench fits under the saddle with good access to the bolts. For the ones that don't I use this:

__________________
My Bikes
Andy_K is offline  
Likes For Andy_K:
Old 02-12-22, 01:01 PM
  #3  
bikingshearer 
Crawlin' up, flyin' down
 
bikingshearer's Avatar
 
Join Date: Jan 2006
Location: Democratic Peoples' Republic of Berkeley
Posts: 5,625

Bikes: 1967 Paramount; 1982-ish Ron Cooper; 1978 Eisentraut "A"; two mid-1960s Cinelli Speciale Corsas; and others in various stages of non-rideability.

Mentioned: 40 Post(s)
Tagged: 0 Thread(s)
Quoted: 1008 Post(s)
Liked 2,465 Times in 1,030 Posts
Originally Posted by Andy_K
Most of the bikes I use Campy two bolt seatposts on have modern plastic saddles and a standard 10mm wrench fits under the saddle with good access to the bolts. For the ones that don't I use this:

Use this. I have a combo wrench like this that has no swivel, just a bit of offset - it works well, too. Go in from the back and be prepared to work the ratchet head back and forth a bunch of times. Very easy and surprisingly quick. And the wrench is useful for other things.

FWIW, I always found the Campy bent wrench to be at best a marginal improvement over a regular wrench. It is decidedly inferior to Andy_K's solution.
__________________
"I'm in shape -- round is a shape." Andy Rooney
bikingshearer is offline  
Likes For bikingshearer:
Old 02-12-22, 01:19 PM
  #4  
billnuke1 
Senior Member
 
billnuke1's Avatar
 
Join Date: Dec 2010
Location: St Cloud Fl.
Posts: 1,973

Bikes: Only my riders left...

Mentioned: 6 Post(s)
Tagged: 0 Thread(s)
Quoted: 350 Post(s)
Liked 782 Times in 389 Posts
Definitely not designed for on the fly seat adjustments!
billnuke1 is offline  
Likes For billnuke1:
Old 02-12-22, 01:58 PM
  #5  
Hobbiano 
Senior Member
 
Join Date: Sep 2014
Location: Baton Rouge La
Posts: 1,217
Mentioned: 22 Post(s)
Tagged: 0 Thread(s)
Quoted: 394 Post(s)
Liked 346 Times in 230 Posts
I find that once you loosen one bolt. the other will be loose, too. So, I use a regular combination wrench to loose the one at the rear, then make an adjustment either way on the other bolt, with my fingers, then tighten the rear bolt back up. pretty easy, really. This is with a Brooks saddle, though, some others may be more difficult.
Hobbiano is offline  
Likes For Hobbiano:
Old 02-12-22, 02:11 PM
  #6  
3alarmer 
Friendship is Magic
 
3alarmer's Avatar
 
Join Date: Nov 2010
Location: Sacramento, CA
Posts: 22,932

Bikes: old ones

Mentioned: 304 Post(s)
Tagged: 0 Thread(s)
Quoted: 26249 Post(s)
Liked 10,231 Times in 7,100 Posts
.
...I think maybe the question here is the length and thread pitch, so they can be replaced with socket head screws.


I don't have one handy, and I do not know the answer, but I have used them with cutout saddles before.
Even if you don't replace them, a 10mm socket, with a small extension and a ratchet did the trick in my case.
__________________
3alarmer is offline  
Likes For 3alarmer:
Old 02-12-22, 03:39 PM
  #7  
oneclick 
Senior Member
 
Join Date: Feb 2020
Posts: 2,890
Mentioned: 49 Post(s)
Tagged: 0 Thread(s)
Quoted: 1104 Post(s)
Likes: 0
Liked 1,311 Times in 775 Posts
M7x1
oneclick is offline  
Likes For oneclick:
Old 02-12-22, 04:13 PM
  #8  
SurferRosa
señor miembro
 
SurferRosa's Avatar
 
Join Date: Dec 2018
Location: Pac NW
Posts: 8,305

Bikes: '70s - '80s Campagnolo

Mentioned: 92 Post(s)
Tagged: 0 Thread(s)
Quoted: 3846 Post(s)
Liked 6,437 Times in 3,183 Posts
I don't use a wrench on the front bolt; I use my fingers. I use a ratcheting 10 mm wrench on the rear bolt. I found it on the road. Actually, I found two ratcheting 10 mm wrenches on the road, but I didn't pick up the second one, because the first works perfectly. So it's just trial and error to get the saddle level perfect. If it's tilted up a little too much, I back off the rear bolt, use my fingers on the front bolt to tighten it down, then retighten the rear bolt with the wrench. Once you get it perfect, there's no need to "screw" with it anymore ... unless you just like messing with the 10 mm ratcheting wrench that you found on the road.
SurferRosa is offline  
Likes For SurferRosa:
Old 02-12-22, 04:21 PM
  #9  
repechage
Senior Member
 
Join Date: Jun 2006
Posts: 20,323
Mentioned: 129 Post(s)
Tagged: 0 Thread(s)
Quoted: 3449 Post(s)
Liked 2,800 Times in 1,974 Posts
Originally Posted by oneclick
M7x1
not the easiest to find, a big box center unlikely to have it. I want to say 30-35mm long
repechage is offline  
Likes For repechage:
Old 02-12-22, 05:16 PM
  #10  
Moe Zhoost
Half way there
 
Moe Zhoost's Avatar
 
Join Date: Sep 2015
Location: North Carolina
Posts: 2,955

Bikes: Many, and the list changes frequently

Mentioned: 5 Post(s)
Tagged: 0 Thread(s)
Quoted: 985 Post(s)
Liked 879 Times in 526 Posts
Why don't you just measure what you have. Thread gauges and digital calipers are cheap and I'd recommend them as part of any cyclists toolbox.

BTW, I love those two bolt posts. So much easier to micro-adjust.
Moe Zhoost is offline  
Likes For Moe Zhoost:
Old 02-12-22, 05:24 PM
  #11  
tkamd73 
Senior Member
 
Join Date: Dec 2015
Location: Menomonee Falls, WI
Posts: 1,850

Bikes: 1984 Schwinn Supersport, 1988 Trek 400T, 1977 Trek TX900, 1982 Bianchi Champione del Mondo, 1978 Raleigh Supercourse, 1986 Trek 400 Elance, 1991 Waterford PDG OS Paramount, 1971 Schwinn Sports Tourer, 1985 Trek 670

Mentioned: 7 Post(s)
Tagged: 0 Thread(s)
Quoted: 601 Post(s)
Liked 1,054 Times in 530 Posts
Any 10 mm offset wrench will do, no need for the expensive Campy wrench.
Tim
tkamd73 is offline  
Likes For tkamd73:
Old 02-12-22, 07:44 PM
  #12  
cyclic_eric
Full Member
Thread Starter
 
cyclic_eric's Avatar
 
Join Date: Jan 2013
Location: Oakland CA
Posts: 274

Bikes: 1984 Gitane TdF, 1986 Look Équipe, 1983 Colnago Super

Mentioned: 2 Post(s)
Tagged: 0 Thread(s)
Quoted: 112 Post(s)
Liked 132 Times in 79 Posts
Originally Posted by SurferRosa
I don't use a wrench on the front bolt; I use my fingers. I use a ratcheting 10 mm wrench on the rear bolt. I found it on the road. Actually, I found two ratcheting 10 mm wrenches on the road, but I didn't pick up the second one, because the first works perfectly. So it's just trial and error to get the saddle level perfect. If it's tilted up a little too much, I back off the rear bolt, use my fingers on the front bolt to tighten it down, then retighten the rear bolt with the wrench. Once you get it perfect, there's no need to "screw" with it anymore ... unless you just like messing with the 10 mm ratcheting wrench that you found on the road.


Originally Posted by oneclick
M7x1
Thanks oneclick, what an odd an odd size. Yes, it is unlikely I'll find it at the local hardware store. Perhaps I'll get lucky and happen upon the ratcheting 10mm wrench that SurferRosa didn't pick up! I have a non-bending ratcheting 10mm wrench, not the one Andy_K recommends. Using the advice of others, it looks like the way to go. Thanks y'all
cyclic_eric is offline  
Likes For cyclic_eric:
Old 02-12-22, 09:30 PM
  #13  
SurferRosa
señor miembro
 
SurferRosa's Avatar
 
Join Date: Dec 2018
Location: Pac NW
Posts: 8,305

Bikes: '70s - '80s Campagnolo

Mentioned: 92 Post(s)
Tagged: 0 Thread(s)
Quoted: 3846 Post(s)
Liked 6,437 Times in 3,183 Posts
Originally Posted by cyclic_eric
Perhaps I'll get lucky and happen upon the ratcheting 10mm wrench that SurferRosa didn't pick up! I have a non-bending ratcheting 10mm wrench, not the one Andy_K recommends.
It's been a few years, but it was in the Crown Hill neighborhood on 8th avenue, I believe. You might try there.

But the one you already have is just like it and works fine ... on the rear bolt.

One of the seatposts I bought had a replacement bolt that wasn't Campy. It was long (before I cut it down), and the bolt head had a taller profile than normal. So possibilities are out there. If you have a place like this, try there if necessary:

https://www.tacomascrew.com/

If it's threaded and made of metal, they have it.
SurferRosa is offline  
Old 02-13-22, 01:15 AM
  #14  
merziac
Senior Member
 
merziac's Avatar
 
Join Date: Oct 2015
Location: PDX
Posts: 14,101

Bikes: Merz x 5 + Specialized Merz Allez x 2, Strawberry/Newlands/DiNucci/Ti x3, Gordon, Fuso/Moulton x2, Bornstein, Paisley,1958-74 Paramounts x3, 3rensho, 74 Moto TC, 73-78 Raleigh Pro's x5, Marinoni x2, 1960 Cinelli SC, 1980 Bianchi SC, PX-10 X 2

Mentioned: 267 Post(s)
Tagged: 0 Thread(s)
Quoted: 4493 Post(s)
Liked 6,298 Times in 3,633 Posts
Originally Posted by cyclic_eric


Thanks oneclick, what an odd an odd size. Yes, it is unlikely I'll find it at the local hardware store. Perhaps I'll get lucky and happen upon the ratcheting 10mm wrench that SurferRosa didn't pick up! I have a non-bending ratcheting 10mm wrench, not the one Andy_K recommends. Using the advice of others, it looks like the way to go. Thanks y'all
Any 12 point wrench will work on the back bolt, rachet, flex, plain, etc. very easy to do with very little practice, and yes the bolts can be a bit of a challenge unless Tacoma screw is in your orbit.

I wanted some really long ones to pair with some slitted tubing adapters and an Ideale flat rail saddle.

I think they were $12 from efbay and while I did get the setup to work ok, I didn't refine them enough to use the setup yet.

Anybody got a set of the flat rail adapters for a Campy 2 bolt they want to let go cheap?
merziac is offline  
Old 02-13-22, 09:24 AM
  #15  
JohnDThompson 
Old fart
 
JohnDThompson's Avatar
 
Join Date: Nov 2004
Location: Appleton WI
Posts: 24,935

Bikes: Several, mostly not name brands.

Mentioned: 153 Post(s)
Tagged: 0 Thread(s)
Quoted: 3571 Post(s)
Liked 3,367 Times in 1,916 Posts
Originally Posted by cyclic_eric
Perhaps I'll get lucky and happen upon the ratcheting 10mm wrench that SurferRosa didn't pick up!
Plenty available on eBay:

https://www.ebay.com/sch/i.html?_fro...tchet&_sacat=0
JohnDThompson is online now  
Likes For JohnDThompson:
Old 02-13-22, 05:35 PM
  #16  
Choke 
Disciple of St. Tullio
 
Choke's Avatar
 
Join Date: Jul 2008
Location: State of Jefferson
Posts: 740

Bikes: Ciöcc, Bianchi, DeRosa, Eddy Merckx, Frejus, Hampsten, Kondor, Losa, Magni, Pegoretti, Pelizzoli, Pogliaghi, Scapin

Mentioned: 37 Post(s)
Tagged: 0 Thread(s)
Quoted: 264 Post(s)
Liked 326 Times in 138 Posts
On at least one bike with a saddle cutout, I was able to use a 1/4" 10mm socket and extension to tighten the bolts. Obviously that would depend on where the cutout sets in comparison to the cutout.
Choke is offline  
Old 02-13-22, 07:07 PM
  #17  
John E
feros ferio
 
John E's Avatar
 
Join Date: Jul 2000
Location: www.ci.encinitas.ca.us
Posts: 21,765

Bikes: 1959 Capo Modell Campagnolo; 1960 Capo Sieger (2); 1962 Carlton Franco Suisse; 1970 Peugeot UO-8; 1982 Bianchi Campione d'Italia; 1988 Schwinn Project KOM-10;

Mentioned: 44 Post(s)
Tagged: 0 Thread(s)
Quoted: 1384 Post(s)
Liked 1,294 Times in 819 Posts
Originally Posted by Choke
On at least one bike with a saddle cutout, I was able to use a 1/4" 10mm socket and extension to tighten the bolts. Obviously that would depend on where the cutout sets in comparison to the cutout.
Yup -- it would be a breeze with a Brooks Swallow, even though this bike didn't come with a Campag. seatpost.

As obtained from my wife's younger sister. Just my size. 27" steel rims are going, along with the completely rotted tires.
__________________
"Far and away the best prize that life offers is the chance to work hard at work worth doing." --Theodore Roosevelt
Capo: 1959 Modell Campagnolo, S/N 40324; 1960 Sieger (2), S/N 42624, 42597
Carlton: 1962 Franco Suisse, S/N K7911
Peugeot: 1970 UO-8, S/N 0010468
Bianchi: 1982 Campione d'Italia, S/N 1.M9914
Schwinn: 1988 Project KOM-10, S/N F804069
John E is offline  
Old 02-13-22, 10:31 PM
  #18  
ofajen
Cheerfully low end
 
ofajen's Avatar
 
Join Date: Jun 2020
Posts: 1,965
Mentioned: 5 Post(s)
Tagged: 0 Thread(s)
Quoted: 642 Post(s)
Liked 1,040 Times in 663 Posts
I’ve had one of those for a bit over forty years. I never had any issue with a normal 10mm open end wrench. And a very nice post for fine adjustments. My current frames aren’t 27.2mm so I’m not using it at the moment.

Otto
ofajen is offline  
Likes For ofajen:
Old 02-13-22, 10:59 PM
  #19  
Road Fan
Senior Member
 
Road Fan's Avatar
 
Join Date: Apr 2005
Location: Ann Arbor, MI
Posts: 16,853

Bikes: 1980 Masi, 1984 Mondonico, 1984 Trek 610, 1980 Woodrup Giro, 2005 Mondonico Futura Leggera ELOS, 1967 PX10E, 1971 Peugeot UO-8

Mentioned: 49 Post(s)
Tagged: 0 Thread(s)
Quoted: 1851 Post(s)
Liked 654 Times in 498 Posts
Originally Posted by Moe Zhoost
Why don't you just measure what you have. Thread gauges and digital calipers are cheap and I'd recommend them as part of any cyclists toolbox.

BTW, I love those two bolt posts. So much easier to micro-adjust.
Absolutely, just measure it! If you don't have the tools, take it to a real good hardware store and htey should be able to send you away with the correct numbers
Road Fan is offline  
Old 02-14-22, 12:42 AM
  #20  
cyclic_eric
Full Member
Thread Starter
 
cyclic_eric's Avatar
 
Join Date: Jan 2013
Location: Oakland CA
Posts: 274

Bikes: 1984 Gitane TdF, 1986 Look Équipe, 1983 Colnago Super

Mentioned: 2 Post(s)
Tagged: 0 Thread(s)
Quoted: 112 Post(s)
Liked 132 Times in 79 Posts
Thanks everyone for the advice and especially the humor!
Sorry for any confusion - I do not have the seatpost yet. It should arrive next week. I was hoping to get the dimensions ahead of time, before my seatpost arrives.
I thought I might get a pair of replacement hex screws ahead of time. But it sounds easy enough to keep the stock bolts. And the original Campagnolo bolts have a nice fit in the yokes.
I do have tools for measuring thread pitch, along with a variety of 10mm wrenches, sockets, nut drivers, etc. I like messing around with them, but I rarely find them in the road.
cyclic_eric is offline  
Old 02-17-22, 06:14 PM
  #21  
Road Fan
Senior Member
 
Road Fan's Avatar
 
Join Date: Apr 2005
Location: Ann Arbor, MI
Posts: 16,853

Bikes: 1980 Masi, 1984 Mondonico, 1984 Trek 610, 1980 Woodrup Giro, 2005 Mondonico Futura Leggera ELOS, 1967 PX10E, 1971 Peugeot UO-8

Mentioned: 49 Post(s)
Tagged: 0 Thread(s)
Quoted: 1851 Post(s)
Liked 654 Times in 498 Posts
Originally Posted by cyclic_eric


Thanks oneclick, what an odd an odd size. Yes, it is unlikely I'll find it at the local hardware store. Perhaps I'll get lucky and happen upon the ratcheting 10mm wrench that SurferRosa didn't pick up! I have a non-bending ratcheting 10mm wrench, not the one Andy_K recommends. Using the advice of others, it looks like the way to go. Thanks y'all
If you're worried about finding the bolt, I would say first take your bolt to the hardware store and get them to measure it - write it all down. Then go to their stacks of Vidmar shelves or whatever where you can find if a steel bolt of the correct head, length, shaft diameter, and shaft threading is available for you. If you can't find one, take your little sheet of specifications and search on the McMaster-Carr website, or call them and get direct assistance. If you have a choice, take a good look at the available finishes or platings which may be available to you. Hardened steel is good, but it can rust. I believe Campy bolts were originally chromed, but I'm not sure they can be duplicated. This is another example of "please try not to lose the original fasteners from your vintage bike parts."
Road Fan is offline  
Likes For Road Fan:
Old 02-17-22, 10:01 PM
  #22  
cyclic_eric
Full Member
Thread Starter
 
cyclic_eric's Avatar
 
Join Date: Jan 2013
Location: Oakland CA
Posts: 274

Bikes: 1984 Gitane TdF, 1986 Look Équipe, 1983 Colnago Super

Mentioned: 2 Post(s)
Tagged: 0 Thread(s)
Quoted: 112 Post(s)
Liked 132 Times in 79 Posts
It turned out to be much simpler than I thought. I have a small 10mm wrench that is easy to fit and light enough for jersey pockets.
While at home I thought of the scrap wood set up below. A digital level app for my phone is probably more accuracy than needed.



cyclic_eric is offline  
Old 02-17-22, 10:38 PM
  #23  
TPL
Senior Member
 
Join Date: Jul 2017
Posts: 248
Mentioned: 1 Post(s)
Tagged: 0 Thread(s)
Quoted: 143 Post(s)
Likes: 0
Liked 90 Times in 64 Posts
use a 10 mm wrench
TPL is offline  

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


Thread Tools
Search this Thread

Contact Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service -

Copyright © 2024 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.