Go Back  Bike Forums > Bike Forums > General Cycling Discussion
Reload this Page >

Pickup Bed Bike Rack Options

Notices
General Cycling Discussion Have a cycling related question or comment that doesn't fit in one of the other specialty forums? Drop on in and post in here! When possible, please select the forum above that most fits your post!

Pickup Bed Bike Rack Options

Old 10-13-21, 04:46 PM
  #1  
TravellingFool
Member
Thread Starter
 
Join Date: Aug 2015
Posts: 26
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 8 Post(s)
Likes: 0
Liked 3 Times in 2 Posts
Pickup Bed Bike Rack Options

Hi, in the market for a new vehicle and a small/mid sized pickup ticks the boxes (most likely a Ridgeline). I know I can put a hitch mount rack on, but am looking at in-bed options.

Seems like a bar with a couple of front fork quick release attachment points is an obvious, straightforward, and reasonably secure answer. Any thoughts on if there's a better solution you've come across or generally any comments on this?

Thanks!
TravellingFool is offline  
Old 10-13-21, 05:23 PM
  #2  
Hasek
Senior Member
 
Hasek's Avatar
 
Join Date: Jul 2008
Posts: 132

Bikes: 1997 or 6 Giant Rincon, 2015 Surly LHT, 1999 Schwinn Peloton.

Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 15 Post(s)
Liked 9 Times in 5 Posts
The bar with quick release hubs works. Check the below out. I'll be getting a new work truck in January and am gonna try these. They make 2 different kinds for depending on what type of bed rail. https://usa.innoracks.com/

Hasek is offline  
Old 10-13-21, 05:38 PM
  #3  
rlmalisz
Junior Member
 
Join Date: Jul 2020
Posts: 91
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 33 Post(s)
Likes: 0
Liked 75 Times in 35 Posts
I rolled my own (with some yakima bits, so I could keep it all keyed the same as everythig else. First photo is the original setup, before I added a through-axle bike to the stable. But the thing works, obviously doesn't secure the through-axle bike. But I can install/remove it from the bed in a couple minutes, and until the truck went into the shop, was just leaving it on. For all of our bikes, I can put two bikes in the back with the Van Tech bed rack and iKamper Skycamp Mini mounted.



rlmalisz is offline  
Old 10-13-21, 06:11 PM
  #4  
DMC707
Senior Member
 
DMC707's Avatar
 
Join Date: Jan 2013
Location: Norman, Oklahoma
Posts: 5,389

Bikes: Too many to list

Mentioned: 36 Post(s)
Tagged: 0 Thread(s)
Quoted: 1764 Post(s)
Liked 1,119 Times in 743 Posts
KISS

Motorcycle tie down straps i have found to be easier to deal with than the racks where you have to pop the front wheel off and secure it with a quick release -- just undo the straps and go

I however, use a Thule hitch mount with my Tacoma because i like to leave a bed cover on it to keep my tool boxes , gearbags and drink coolers, etc secure
DMC707 is offline  
Old 10-13-21, 06:25 PM
  #5  
jaxgtr
Senior Member
 
jaxgtr's Avatar
 
Join Date: Jul 2006
Location: Jacksonville, FL
Posts: 6,830

Bikes: Trek Domane SLR 7 AXS, Trek CheckPoint SL7, Trek Emonda ALR, Trek FX 5 Sport

Mentioned: 2 Post(s)
Tagged: 0 Thread(s)
Quoted: 751 Post(s)
Liked 1,666 Times in 980 Posts
Originally Posted by Hasek
The bar with quick release hubs works. Check the below out. I'll be getting a new work truck in January and am gonna try these. They make 2 different kinds for depending on what type of bed rail. https://usa.innoracks.com/
@TravellingFool, I saw these and they look intriguing, downside with those is that the Ridgeline does not have anyway to lock it into place unless you get some sort of bar like you would have for a Tonneau cover. I have a 2018 Ridgeline so I just keep that in your thoughts....

I personally have a 1UP Hitchrack and I like not having to pull the wheel.
__________________
Brian | 2023 Trek Domane SLR 7 AXS | 2023 Trek CheckPoint SL 7 AXS | 2016 Trek Emonda ALR | 2022 Trek FX Sport 5
Originally Posted by AEO
you should learn to embrace change, and mock it's failings every step of the way.




Last edited by jaxgtr; 10-13-21 at 06:29 PM.
jaxgtr is offline  
Old 10-13-21, 07:18 PM
  #6  
hose
Miyata Mike
 
hose's Avatar
 
Join Date: Jun 2021
Location: belchertown, MA
Posts: 185
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 70 Post(s)
Liked 66 Times in 46 Posts
Am i the only one that just throws their bike in the bed and... it doesnt move?
hose is offline  
Old 10-14-21, 01:16 AM
  #7  
Lazyass
Senior Member
 
Join Date: Jul 2008
Location: Minas Ithil
Posts: 9,337
Mentioned: 66 Post(s)
Tagged: 0 Thread(s)
Quoted: 2432 Post(s)
Liked 638 Times in 395 Posts
No need for all that. In my Silverado I just strap it down motorcycle style. A soft tie on each side of the bar attached to friction straps connected to the bed hooks. You can also attach a strap to each side of the rear of the bike. Takes about a minute to get her strapped in. Drove from New Jersey to El Paso like that with no problems.

You can get soft ties for three bucks.

https://www.harborfreight.com/soft-l...saAucDEALw_wcB
Lazyass is offline  
Old 10-14-21, 06:49 AM
  #8  
TravellingFool
Member
Thread Starter
 
Join Date: Aug 2015
Posts: 26
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 8 Post(s)
Likes: 0
Liked 3 Times in 2 Posts
Thanks folks, it's appreciated.

hose , no you're not the only one. I'm just not willing to do that either with my tri bike, or for any distance. Personal choice.
TravellingFool is offline  
Old 10-14-21, 06:56 AM
  #9  
easyupbug 
Senior Member
 
Join Date: Jan 2013
Posts: 2,652

Bikes: too many sparkly Italians, some sweet Americans and a couple interesting Japanese

Mentioned: 9 Post(s)
Tagged: 0 Thread(s)
Quoted: 560 Post(s)
Liked 546 Times in 396 Posts
Originally Posted by hose
Am i the only one that just throws their bike in the bed and... it doesnt move?
On a website full of bicycle aficionados it would not be a surprise to me.
easyupbug is offline  
Old 10-14-21, 09:29 AM
  #10  
prj71
Senior Member
 
Join Date: Jun 2015
Location: North Central Wisconsin
Posts: 4,598
Mentioned: 14 Post(s)
Tagged: 0 Thread(s)
Quoted: 2964 Post(s)
Liked 1,163 Times in 760 Posts
Originally Posted by hose
Am i the only one that just throws their bike in the bed and... it doesnt move?
One bike yes. I do it all the time.

Multiple bikes...you want a rack system of sorts to stand them up. Otherwise they can get scratched / damaged if they are piled on top of one another or leaned up against the bed sides.

I made a rack out of a 2 x 4 and some PVC pipe for my thru axle bikes.

Last edited by prj71; 10-14-21 at 09:36 AM.
prj71 is offline  
Old 10-14-21, 10:50 AM
  #11  
locolobo13 
Senior Member
 
locolobo13's Avatar
 
Join Date: Oct 2011
Location: Phx, AZ
Posts: 2,108

Bikes: Trek Mtn Bike

Mentioned: 5 Post(s)
Tagged: 0 Thread(s)
Quoted: 280 Post(s)
Liked 2,601 Times in 930 Posts
Originally Posted by hose
Am i the only one that just throws their bike in the bed and... it doesnt move?
Me too. But it does slide back and forth in rush hour. The bed and sometimes the bike get a little scratched.
locolobo13 is offline  
Old 10-14-21, 10:50 AM
  #12  
icemilkcoffee 
Senior Member
 
icemilkcoffee's Avatar
 
Join Date: Aug 2009
Posts: 2,586
Mentioned: 13 Post(s)
Tagged: 0 Thread(s)
Quoted: 1538 Post(s)
Liked 1,696 Times in 953 Posts
Position the crank up and lean that against the side of the bed. Tie it down with bungee cords.
I regularly carry 4 bikes in the truck bed with no rack.
icemilkcoffee is offline  
Old 10-14-21, 11:31 AM
  #13  
sarhog
Full Member
 
Join Date: Jul 2019
Location: Greer, SC
Posts: 344

Bikes: GR300, Grail, Live Wire, 5010

Mentioned: 1 Post(s)
Tagged: 0 Thread(s)
Quoted: 189 Post(s)
Liked 241 Times in 121 Posts
Originally Posted by icemilkcoffee
Position the crank up and lean that against the side of the bed. Tie it down with bungee cords.
I regularly carry 4 bikes in the truck bed with no rack.
He wants to use a Ridgeline, he will be lucky to get 1 in there.
sarhog is offline  
Old 10-14-21, 12:34 PM
  #14  
prj71
Senior Member
 
Join Date: Jun 2015
Location: North Central Wisconsin
Posts: 4,598
Mentioned: 14 Post(s)
Tagged: 0 Thread(s)
Quoted: 2964 Post(s)
Liked 1,163 Times in 760 Posts
Originally Posted by icemilkcoffee
Position the crank up and lean that against the side of the bed. Tie it down with bungee cords.
I regularly carry 4 bikes in the truck bed with no rack.
scratched and damaged good...
prj71 is offline  
Old 10-14-21, 01:11 PM
  #15  
Riveting
Senior Member
 
Join Date: Oct 2013
Location: Highlands Ranch, CO
Posts: 1,221

Bikes: '13 Diamondback Hybrid Commuter, '17 Spec Roubaix Di2, '17 Spec Camber 29'er, '19 CDale Topstone Gravel

Mentioned: 5 Post(s)
Tagged: 0 Thread(s)
Quoted: 590 Post(s)
Liked 445 Times in 260 Posts
Originally Posted by rlmalisz
I rolled my own.
I'm getting a new SUV (Honda CRV) next week to that can transport my bikes in inside and upright (the CRV is the only vehicle I found that can do that with a 29er mtb, and I actually brought my mtb to all of the test drives just to test it out., and if the bike didn't fit, I didn't even bother to test drive it), and you just gave me the great idea to use 80/20 for the fork mounts so that I can easily adjust their positions.

Is there anything 80/20 can't do?!!
Riveting is offline  
Old 10-14-21, 01:21 PM
  #16  
icemilkcoffee 
Senior Member
 
icemilkcoffee's Avatar
 
Join Date: Aug 2009
Posts: 2,586
Mentioned: 13 Post(s)
Tagged: 0 Thread(s)
Quoted: 1538 Post(s)
Liked 1,696 Times in 953 Posts
Originally Posted by prj71
scratched and damaged good...
Well, I guess the side of the pedal is kind of scratching the plastic liner of the truck bed.
icemilkcoffee is offline  
Old 10-14-21, 09:10 PM
  #17  
jolathe
Junior Member
 
Join Date: May 2020
Posts: 7
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 2 Post(s)
Liked 7 Times in 3 Posts
I use a tailgate pad. Wrapping something around the downtube before strapping it in prevents abrasion from the strap. My pad is a Dakine and carries 7 bikes.
jolathe is offline  
Old 10-15-21, 07:55 AM
  #18  
prj71
Senior Member
 
Join Date: Jun 2015
Location: North Central Wisconsin
Posts: 4,598
Mentioned: 14 Post(s)
Tagged: 0 Thread(s)
Quoted: 2964 Post(s)
Liked 1,163 Times in 760 Posts
Originally Posted by icemilkcoffee
Well, I guess the side of the pedal is kind of scratching the plastic liner of the truck bed.
Show us your 4 bikes in there.
prj71 is offline  
Old 10-15-21, 08:08 AM
  #19  
oris
I like speed
 
oris's Avatar
 
Join Date: Nov 2008
Location: Eastvale, CA
Posts: 219

Bikes: Cannondale SuperSix Hi Mod, Specialized Allez Sprint, Bottecchia Emme 4 SL

Mentioned: 1 Post(s)
Tagged: 0 Thread(s)
Quoted: 77 Post(s)
Liked 121 Times in 61 Posts
I personally use the Thule Insta Gator on my F150; picked one up cheap from JensonUSA that had the box damaged in shipping.

Another option is to make your own PVC pipe rack for the bed and use bungees to hold it all in.
oris is offline  
Likes For oris:
Old 10-15-21, 08:12 AM
  #20  
sarhog
Full Member
 
Join Date: Jul 2019
Location: Greer, SC
Posts: 344

Bikes: GR300, Grail, Live Wire, 5010

Mentioned: 1 Post(s)
Tagged: 0 Thread(s)
Quoted: 189 Post(s)
Liked 241 Times in 121 Posts
Originally Posted by oris
I personally use the Thule Insta Gator on my F150; picked one up cheap from JensonUSA that had the box damaged in shipping.

Another option is to make your own PVC pipe rack for the bed and use bungees to hold it all in.
I used a Thule Instagater when I had a truck, it does a pretty good job, however the bar that holds the tire down is too wide to fit between the front tire and the down tube on my road bikes. It’s still usable, but you have to cock the wheel to the side when putting the bike in there. I’d think that a Ridgeline bed would be too short for most modern mountain bikes.
sarhog is offline  
Old 10-15-21, 11:06 AM
  #21  
downhillmaster
Senior Member
 
Join Date: May 2018
Posts: 1,682
Mentioned: 9 Post(s)
Tagged: 0 Thread(s)
Quoted: 980 Post(s)
Liked 776 Times in 402 Posts
Originally Posted by hose
Am i the only one that just throws their bike in the bed and... it doesnt move?
I also do that on occasion with my bikes, but no way in the world your bike does not move if you are driving and it is unsecured in the bed.
It’s ofc doable but certainly not the best option.
downhillmaster is offline  
Old 10-15-21, 12:09 PM
  #22  
icemilkcoffee 
Senior Member
 
icemilkcoffee's Avatar
 
Join Date: Aug 2009
Posts: 2,586
Mentioned: 13 Post(s)
Tagged: 0 Thread(s)
Quoted: 1538 Post(s)
Liked 1,696 Times in 953 Posts
Originally Posted by prj71
Show us your 4 bikes in there.
To be fair, My kids' bikes are 650c wheeled road bikes and my wife's bike is a small Terry style bike as well, So they are not 4 full sized bikes.
But I don't see why you couldn't lean and tie down 3 road bikes along the two sides and the back of the truck bed.
icemilkcoffee is offline  
Old 10-15-21, 02:50 PM
  #23  
jaxgtr
Senior Member
 
jaxgtr's Avatar
 
Join Date: Jul 2006
Location: Jacksonville, FL
Posts: 6,830

Bikes: Trek Domane SLR 7 AXS, Trek CheckPoint SL7, Trek Emonda ALR, Trek FX 5 Sport

Mentioned: 2 Post(s)
Tagged: 0 Thread(s)
Quoted: 751 Post(s)
Liked 1,666 Times in 980 Posts
Originally Posted by TravellingFool
Thanks folks, it's appreciated.

hose , no you're not the only one. I'm just not willing to do that either with my tri bike, or for any distance. Personal choice.

+1. I just do not want to put my very expensive bikes in the back of my truck. It was worth it to me to spend the few hundred dollars for the hitch rack.
__________________
Brian | 2023 Trek Domane SLR 7 AXS | 2023 Trek CheckPoint SL 7 AXS | 2016 Trek Emonda ALR | 2022 Trek FX Sport 5
Originally Posted by AEO
you should learn to embrace change, and mock it's failings every step of the way.



jaxgtr is offline  
Old 10-15-21, 03:48 PM
  #24  
Blues
Member
 
Join Date: Jul 2020
Location: Cabarrus County, North Carolina, USA
Posts: 34

Bikes: Some vintage and all projects. Geezer road, road, cruise, some gravel, not much mountain.

Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 13 Post(s)
Liked 22 Times in 16 Posts
Bike in a small pickup

My favorite bike transportation method in my Ford Ranger is to run a 1/4" line from the saddle around the side rail at the top of the truck side bed wall and back to the stem. I do the line fastening with the bike standing upright a foot from the bed wall. When tied off, I brace my elbows on top of the bed side and grab the fork and seat stay and tilt the tires into the corner of the pickup wall and floor. The line is adjusted so the bike is leaning toward the mid-line of the truck at abut a 45 degree angle, and the tires perfectly span the wheel well, immobilizing the bike. We can fit two bikes in the Ranger short bed. To get the bikes out, just reverse the whole process. The Ranger bed is just long enough to close the tail gate. I have loops in the ends of my line, one with a slip knot, so adjustment is quick. For a longer trip I will tie the top of the bike to the other side of the truck bed, so if I was in a fender bender the bike would stay in the truck bed. This system also works on my Wife's Colorado.

Last edited by Blues; 10-17-21 at 07:47 PM. Reason: re-write and add photo
Blues is offline  
Old 10-15-21, 05:21 PM
  #25  
Steve B.
Senior Member
 
Join Date: Jul 2007
Location: South shore, L.I., NY
Posts: 6,825

Bikes: Flyxii FR322, Cannondale Topstone, Miyata City Liner, Specialized Chisel, Specialized Epic Evo

Mentioned: 18 Post(s)
Tagged: 0 Thread(s)
Quoted: 3185 Post(s)
Liked 2,020 Times in 1,158 Posts
Originally Posted by jaxgtr
+1. I just do not want to put my very expensive bikes in the back of my truck. It was worth it to me to spend the few hundred dollars for the hitch rack.
Much safer in the bed of a P/U if done carefully. A hitch always gets hit if you get rear ended.
Steve B. is offline  

Thread Tools
Search this Thread

Contact Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service -

Copyright © 2024 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.