Go Back  Bike Forums > Bike Forums > General Cycling Discussion
Reload this Page >

Optimal pressure for a 700x26 tire

Notices
General Cycling Discussion Have a cycling related question or comment that doesn't fit in one of the other specialty forums? Drop on in and post in here! When possible, please select the forum above that most fits your post!

Optimal pressure for a 700x26 tire

Old 01-16-23, 06:44 AM
  #1  
papaki72
Newbie
Thread Starter
 
papaki72's Avatar
 
Join Date: Oct 2017
Location: Athens, Greece
Posts: 73

Bikes: Specialized Allez Sport Sora (now), Whistle Modod Flatbar (retired)

Mentioned: 1 Post(s)
Tagged: 0 Thread(s)
Quoted: 42 Post(s)
Liked 20 Times in 16 Posts
Optimal pressure for a 700x26 tire

I have been watching recently videos about lowering the pressure of your tires to get better performance. The sidewalls of my Roadsport 700x26 tires read 100-120psi. I have used the SRAM pressure calculator and it goes as low as 70psi! Is that safe? Would a pressure that low mean looking for trouble?
papaki72 is offline  
Old 01-16-23, 07:17 AM
  #2  
easyupbug 
Senior Member
 
Join Date: Jan 2013
Posts: 2,652

Bikes: too many sparkly Italians, some sweet Americans and a couple interesting Japanese

Mentioned: 9 Post(s)
Tagged: 0 Thread(s)
Quoted: 560 Post(s)
Liked 546 Times in 396 Posts
Depends on your combined weight, road conditions, speeds, tire/tube?, measured width, etc. I go as low as 80 in the front w/o trouble..
easyupbug is offline  
Likes For easyupbug:
Old 01-16-23, 07:43 AM
  #3  
Kontact
Senior Member
 
Kontact's Avatar
 
Join Date: Apr 2011
Posts: 6,825
Mentioned: 41 Post(s)
Tagged: 0 Thread(s)
Quoted: 4260 Post(s)
Liked 1,458 Times in 950 Posts
Don't worry about the minimum pressure. That is probably just there to make sure you get the tire seated or so customers don't complain about pinch flats. But if you are light enough to get a 70 PSI recommendation you aren't going to pinch flat - that's part of the calculation.
Kontact is offline  
Likes For Kontact:
Old 01-16-23, 08:03 AM
  #4  
Koyote
Senior Member
 
Join Date: Sep 2017
Posts: 7,768
Mentioned: 37 Post(s)
Tagged: 0 Thread(s)
Quoted: 6882 Post(s)
Liked 10,875 Times in 4,639 Posts
Ask smd4 what pressure he’s running and then subtract 30%.

Otherwise just follow the online calculator’s recommendation and adjust up or down in small increments as needed.
Koyote is online now  
Likes For Koyote:
Old 01-16-23, 08:12 AM
  #5  
Fahrenheit531 
52psi
 
Fahrenheit531's Avatar
 
Join Date: Aug 2013
Location: Tucson, AZ
Posts: 4,134

Bikes: Schwinn Volare ('78); Raleigh Competition GS ('79)

Mentioned: 29 Post(s)
Tagged: 0 Thread(s)
Quoted: 790 Post(s)
Liked 800 Times in 390 Posts
Google 15% tire drop chart. Then do the math.
__________________
A race bike in any era is a highly personal choice that at its "best" balances the requirements of fit, weight, handling, durability and cost tempered by the willingness to toss it and oneself down the pavement at considerable speed. ~Bandera
Fahrenheit531 is offline  
Likes For Fahrenheit531:
Old 01-16-23, 08:31 AM
  #6  
Iride01 
I'm good to go!
 
Iride01's Avatar
 
Join Date: Jul 2017
Location: Mississippi
Posts: 14,811

Bikes: Tarmac Disc Comp Di2 - 2020

Mentioned: 50 Post(s)
Tagged: 0 Thread(s)
Quoted: 6100 Post(s)
Liked 4,732 Times in 3,262 Posts
You can try it out and find out for yourself. You should be able to tell pretty quick if it isn't a tire pressure you wish to ride. Your legs will tell you if they like pedaling at that pressure or your butt will tell you if the tire pressure is too squirrely on turns.

If these are tubed tires and you have pinch flats, then the PSI is probably too low for your conditions.
Iride01 is online now  
Old 01-16-23, 08:35 AM
  #7  
Steve B.
Senior Member
 
Join Date: Jul 2007
Location: South shore, L.I., NY
Posts: 6,826

Bikes: Flyxii FR322, Cannondale Topstone, Miyata City Liner, Specialized Chisel, Specialized Epic Evo

Mentioned: 18 Post(s)
Tagged: 0 Thread(s)
Quoted: 3185 Post(s)
Liked 2,020 Times in 1,158 Posts
Tire Pressure Calculator – Rene Herse Cycles
Steve B. is offline  
Likes For Steve B.:
Old 01-16-23, 09:47 AM
  #8  
JohnDThompson 
Old fart
 
JohnDThompson's Avatar
 
Join Date: Nov 2004
Location: Appleton WI
Posts: 24,936

Bikes: Several, mostly not name brands.

Mentioned: 153 Post(s)
Tagged: 0 Thread(s)
Quoted: 3571 Post(s)
Liked 3,368 Times in 1,916 Posts
Here's another one:
https://silca.cc/pages/app-tire-pressure-calculator
JohnDThompson is offline  
Likes For JohnDThompson:
Old 01-17-23, 06:48 PM
  #9  
DaveSSS 
Senior Member
 
Join Date: Sep 2008
Location: Loveland, CO
Posts: 7,215

Bikes: Cinelli superstar disc, two Yoeleo R12

Mentioned: 3 Post(s)
Tagged: 0 Thread(s)
Quoted: 1091 Post(s)
Liked 555 Times in 444 Posts
I've been using the zipp pressure calculator for a couple of years, since I switched to tubeless. They recommend 52/56 psi for my 28mm tires on 25mm IW hookless rims. No problem.

Some of the pressures recommended for tubed setups might be prone to pinch flats.
DaveSSS is offline  
Old 01-17-23, 09:18 PM
  #10  
Lombard
Sock Puppet
 
Lombard's Avatar
 
Join Date: Oct 2022
Location: Planet Earth
Posts: 1,701

Bikes: 2014 Cannondale Synapse Carbon, 2017 Jamis Renegade Exploit and too many others to mention.

Mentioned: 4 Post(s)
Tagged: 0 Thread(s)
Quoted: 1031 Post(s)
Liked 863 Times in 573 Posts
Originally Posted by DaveSSS
Some of the pressures recommended for tubed setups might be prone to pinch flats.
That depends. If you watch where you are going, you can get away with pressures quite low without getting pinch flats. If you hit a large enough pothole, you can get a pinch flat even at bomber pressures.
Lombard is offline  
Old 01-17-23, 09:40 PM
  #11  
79pmooney
Senior Member
 
79pmooney's Avatar
 
Join Date: Oct 2014
Location: Portland, OR
Posts: 12,830

Bikes: (2) ti TiCycles, 2007 w/ triple and 2011 fixed, 1979 Peter Mooney, ~1983 Trek 420 now fixed and ~1973 Raleigh Carlton Competition gravel grinder

Mentioned: 128 Post(s)
Tagged: 0 Thread(s)
Quoted: 4746 Post(s)
Liked 3,861 Times in 2,510 Posts
Originally Posted by Lombard
That depends. If you watch where you are going, you can get away with pressures quite low without getting pinch flats. If you hit a large enough pothole, you can get a pinch flat even at bomber pressures.
I was going to add that some riders are hard on wheels and more prone to pinch flat (dent rims, cut and bruise tires, etc.). All who've mechanic'd a while know some of those. Those riders need more pressure than I do at my weight and on the same roads. That said, I don't like squishy tires unless I'm on ice or other very slippery surfaces and don't come close to pinch flat pressures.
79pmooney is offline  
Old 01-17-23, 10:04 PM
  #12  
tomato coupe
Senior Member
 
Join Date: Jul 2009
Posts: 5,879

Bikes: Colnago, Van Dessel, Factor, Cervelo, Ritchey

Mentioned: 5 Post(s)
Tagged: 0 Thread(s)
Quoted: 3906 Post(s)
Liked 7,182 Times in 2,905 Posts
Originally Posted by 79pmooney
I was going to add that some riders are hard on wheels and more prone to pinch flat (dent rims, cut and bruise tires, etc.). All who've mechanic'd a while know some of those. Those riders need more pressure than I do at my weight and on the same roads. That said, I don't like squishy tires unless I'm on ice or other very slippery surfaces and don't come close to pinch flat pressures.
Yep, some people ride heavier than their weight.
tomato coupe is offline  
Likes For tomato coupe:
Old 01-18-23, 06:30 AM
  #13  
Lombard
Sock Puppet
 
Lombard's Avatar
 
Join Date: Oct 2022
Location: Planet Earth
Posts: 1,701

Bikes: 2014 Cannondale Synapse Carbon, 2017 Jamis Renegade Exploit and too many others to mention.

Mentioned: 4 Post(s)
Tagged: 0 Thread(s)
Quoted: 1031 Post(s)
Liked 863 Times in 573 Posts
Originally Posted by 79pmooney
I was going to add that some riders are hard on wheels and more prone to pinch flat (dent rims, cut and bruise tires, etc.). All who've mechanic'd a while know some of those. Those riders need more pressure than I do at my weight and on the same roads. That said, I don't like squishy tires unless I'm on ice or other very slippery surfaces and don't come close to pinch flat pressures.
What do you consider "squishy"? I ride 70F/80R on my 28's and 45F/50R on my 42's and I'm around 175lbs. That is a little higher than what the calculators display, but I'm lazy and only check pressures once a week or so.
Lombard is offline  
Likes For Lombard:
Old 01-26-23, 09:50 AM
  #14  
rumrunn6
Senior Member
 
rumrunn6's Avatar
 
Join Date: Jul 2008
Location: 25 miles northwest of Boston
Posts: 29,528

Bikes: Bottecchia Sprint, GT Timberline 29r, Marin Muirwoods 29er, Trek FX Alpha 7.0

Mentioned: 112 Post(s)
Tagged: 0 Thread(s)
Quoted: 5220 Post(s)
Liked 3,564 Times in 2,331 Posts
+1 for trial & error

fwiw
I do like the front approx. 10psi lower than the rear
I'm about 223 lbs, then add clothes, a 20lb bike & a 5lb trunk so at about 250lbs I like my rear 25mm tire to be about 100psi, maybe 110 tops, but no higher. the charts say I should go higher but my trial & error has brought me to about 100 rear / 90 front
rumrunn6 is offline  
Likes For rumrunn6:
Old 01-26-23, 11:50 AM
  #15  
SurferRosa
señor miembro
 
SurferRosa's Avatar
 
Join Date: Dec 2018
Location: Pac NW
Posts: 8,237

Bikes: '70s - '80s Campagnolo

Mentioned: 92 Post(s)
Tagged: 0 Thread(s)
Quoted: 3846 Post(s)
Liked 6,437 Times in 3,183 Posts
Sram has a good calculator.

https://axs.sram.com/guides/tire/pressure
SurferRosa is offline  
Old 01-26-23, 12:31 PM
  #16  
RB1-luvr
I don't know.
 
RB1-luvr's Avatar
 
Join Date: May 2003
Location: South Meriden, CT
Posts: 1,976

Bikes: '90 B'stone RB-1, '92 B'stone RB-2, '89 SuperGo Access Comp, '03 Access 69er, '23 Trek 520, '14 Ritchey Road Logic, '09 Kestrel Evoke, '08 Windsor Tourist, '17 Surly Wednesday, '89 Centurion Accordo, '15 CruX, '17 Ridley X-Night

Mentioned: 2 Post(s)
Tagged: 0 Thread(s)
Quoted: 306 Post(s)
Liked 823 Times in 430 Posts
At 170lbs I ride 80 front 85 rear on 25c Vittoria Rubinos.
RB1-luvr is offline  
Likes For RB1-luvr:
Old 01-26-23, 12:37 PM
  #17  
rumrunn6
Senior Member
 
rumrunn6's Avatar
 
Join Date: Jul 2008
Location: 25 miles northwest of Boston
Posts: 29,528

Bikes: Bottecchia Sprint, GT Timberline 29r, Marin Muirwoods 29er, Trek FX Alpha 7.0

Mentioned: 112 Post(s)
Tagged: 0 Thread(s)
Quoted: 5220 Post(s)
Liked 3,564 Times in 2,331 Posts
Originally Posted by SurferRosa
Sram has a good calculator.

https://axs.sram.com/guides/tire/pressure
yeah that is good!

mine came out to
front 94.2 psi
rear 100.2 psi

which is so close to what I use
front 90
rear 100
rumrunn6 is offline  
Likes For rumrunn6:
Old 01-26-23, 02:49 PM
  #18  
ClydeClydeson
Senior Member
 
Join Date: Mar 2019
Posts: 1,606
Mentioned: 8 Post(s)
Tagged: 0 Thread(s)
Quoted: 581 Post(s)
Liked 921 Times in 518 Posts
Originally Posted by koyote
ask smd4 what pressure he’s running and then subtract 30%.
*50%
ClydeClydeson is offline  
Old 01-26-23, 02:54 PM
  #19  
smd4
Senior Member
 
Join Date: Dec 2020
Location: Wake Forest, NC
Posts: 5,642

Bikes: 1989 Cinelli Supercorsa

Mentioned: 11 Post(s)
Tagged: 0 Thread(s)
Quoted: 3431 Post(s)
Liked 2,827 Times in 1,723 Posts
Originally Posted by ClydeClydeson
*50%
Ooof. I can't imagine how sluggish my wheels would feel if I ever let the air out of them to 70 psi...
smd4 is offline  
Old 01-26-23, 03:36 PM
  #20  
Chinghis
Full Member
 
Join Date: Jul 2013
Location: Southern California
Posts: 487

Bikes: Historical: Schwinn Speedster; Schwinn Collegiate; 1981 Ross Gran Tour; 1981 Dawes Atlantis; 1991 Specialized Rockhopper. Current: 1987 Ritchey Ultra; 1987 Centurion Ironman Dave Scott Master; 1992 Specialized Stumpjumper FS

Mentioned: 1 Post(s)
Tagged: 0 Thread(s)
Quoted: 207 Post(s)
Liked 178 Times in 111 Posts
Huh. Just tried this for my old Centurion Ironman with Wolber Alpine rims and 28mm tires, and came up with

PRESSURE SUGGESTIONS
FRONT TIRE
74.8 psi
REAR TIRE
79.6 psi

So, 75 and 80 psi. Just means I can lay off the upper body workout when trying to get to 90 psi ....
Chinghis is offline  
Old 01-26-23, 03:40 PM
  #21  
tomato coupe
Senior Member
 
Join Date: Jul 2009
Posts: 5,879

Bikes: Colnago, Van Dessel, Factor, Cervelo, Ritchey

Mentioned: 5 Post(s)
Tagged: 0 Thread(s)
Quoted: 3906 Post(s)
Liked 7,182 Times in 2,905 Posts
Originally Posted by Chinghis
Huh. Just tried this for my old Centurion Ironman with Wolber Alpine rims and 28mm tires, and came up with

PRESSURE SUGGESTIONS
FRONT TIRE
74.8 psi
REAR TIRE
79.6 psi

So, 75 and 80 psi. Just means I can lay off the upper body workout when trying to get to 90 psi ....
You shouldn't round those numbers -- it will change everything.
tomato coupe is offline  
Old 01-27-23, 12:20 PM
  #22  
Lombard
Sock Puppet
 
Lombard's Avatar
 
Join Date: Oct 2022
Location: Planet Earth
Posts: 1,701

Bikes: 2014 Cannondale Synapse Carbon, 2017 Jamis Renegade Exploit and too many others to mention.

Mentioned: 4 Post(s)
Tagged: 0 Thread(s)
Quoted: 1031 Post(s)
Liked 863 Times in 573 Posts
Originally Posted by smd4
Ooof. I can't imagine how sluggish my wheels would feel if I ever let the air out of them to 70 psi...
You might be pleasantly surprised.
Lombard is offline  
Old 01-27-23, 12:37 PM
  #23  
msu2001la
Senior Member
 
msu2001la's Avatar
 
Join Date: Mar 2006
Location: Chicago, IL, USA
Posts: 2,870
Mentioned: 2 Post(s)
Tagged: 0 Thread(s)
Quoted: 1455 Post(s)
Liked 1,477 Times in 867 Posts
According to the SRAM/Zipp pressure calculator, running numbers for an 18lb bike wearing standard tubed 26mm tires for dry road on 19mm hooked rims:
140lb rider =70psi front/ 74psi rear
150lb rider = 71psi front/76psi rear
160lb rider = 73psi front/78psi rear
170lb rider = 75psi front/80psi rear

I am 165lbs and run 28mm tubeless road tires on 23mm i.d. hookless rims at around 60psi. The calculator suggests I could go 56/60psi for dry and 51/54psi for wet conditions. My floor pump gauge is not accurate enough to dial this in that tight, so I just generally aim for 60 and call it a day. The ride is fine at that pressure and still feels fast.

Last edited by msu2001la; 01-27-23 at 12:43 PM.
msu2001la is offline  
Likes For msu2001la:
Old 01-30-23, 10:56 AM
  #24  
Aardwolf
Wheelman
 
Join Date: Aug 2021
Location: Putney, London UK
Posts: 801

Bikes: 1982 Holdsworth Avanti (531), 1961 Holdsworth Cyclone

Mentioned: 3 Post(s)
Tagged: 0 Thread(s)
Quoted: 278 Post(s)
Liked 632 Times in 320 Posts
Originally Posted by JohnDThompson
The good thing about the Silca one is it has a setting for surface, these: https://cdn.shopify.com/s/files/1/03...Guide.pdf?8341

Being in the city I use "worn pavement / some cracks" which lowers the pressure slightly.
I think in theory this is faster because the tyre absorbs more of the road vibration, it's also a better ride quality.
Aardwolf is offline  

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


Thread Tools
Search this Thread

Contact Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service -

Copyright © 2024 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.