Go Back  Bike Forums > Bike Forums > Bicycle Mechanics
Reload this Page >

thin wrench for hubs

Notices
Bicycle Mechanics Broken bottom bracket? Tacoed wheel? If you're having problems with your bicycle, or just need help fixing a flat, drop in here for the latest on bicycle mechanics & bicycle maintenance.

thin wrench for hubs

Old 06-23-22, 03:50 PM
  #1  
sean.hwy
Senior Member
Thread Starter
 
sean.hwy's Avatar
 
Join Date: Jan 2020
Location: San Jose
Posts: 1,022

Bikes: Blur / Ibis Hakka MX / team machince alr2 / topstone 1

Mentioned: 1 Post(s)
Tagged: 0 Thread(s)
Quoted: 424 Post(s)
Liked 272 Times in 200 Posts
thin wrench for hubs

I have extra thin Facom wrenches from when I was an auto mechanic but it's still wide. Where can I buy 17mm wrench that's thinner than my Facom?
sean.hwy is offline  
Old 06-23-22, 03:56 PM
  #2  
sean.hwy
Senior Member
Thread Starter
 
sean.hwy's Avatar
 
Join Date: Jan 2020
Location: San Jose
Posts: 1,022

Bikes: Blur / Ibis Hakka MX / team machince alr2 / topstone 1

Mentioned: 1 Post(s)
Tagged: 0 Thread(s)
Quoted: 424 Post(s)
Liked 272 Times in 200 Posts

sean.hwy is offline  
Old 06-23-22, 03:58 PM
  #3  
HillRider
Senior Member
 
Join Date: Aug 2005
Location: Pittsburgh, PA
Posts: 33,656

Bikes: '96 Litespeed Catalyst, '05 Litespeed Firenze, '06 Litespeed Tuscany, '20 Surly Midnight Special, All are 3x10. It is hilly around here!

Mentioned: 39 Post(s)
Tagged: 0 Thread(s)
Quoted: 2026 Post(s)
Likes: 0
Liked 1,095 Times in 741 Posts
Park Tools sells thin "cone wrenches" that should be what you want. The sizes available range from 13 to 28mm and 17mm is a common one. Most on-line and local bike shops and Amazon sell them.
HillRider is offline  
Likes For HillRider:
Old 06-23-22, 04:27 PM
  #4  
Crankycrank
Senior Member
 
Join Date: Jan 2009
Location: San Diego, CA
Posts: 3,647
Mentioned: 10 Post(s)
Tagged: 0 Thread(s)
Quoted: 835 Post(s)
Liked 1,053 Times in 739 Posts
+1 ^^^ Park makes good ones or just do a search for "bicycle cone wrenches". Stay away from the cheapie, swiss cheese types as they sometimes bend or have a sloppy fit and slip off the nuts. Since you're an ex-auto mechanic, I think you know what I mean.
Crankycrank is offline  
Likes For Crankycrank:
Old 06-23-22, 04:34 PM
  #5  
WizardOfBoz
Generally bewildered
 
WizardOfBoz's Avatar
 
Join Date: Aug 2015
Location: Eastern PA, USA
Posts: 3,036

Bikes: 2014 Trek Domane 6.9, 1999 LeMond Zurich, 1978 Schwinn Superior

Mentioned: 20 Post(s)
Tagged: 0 Thread(s)
Quoted: 1152 Post(s)
Liked 340 Times in 250 Posts
Originally Posted by Crankycrank
+1 ^^^ Park makes good ones or just do a search for "bicycle cone wrenches". Stay away from the cheapie, swiss cheese types as they sometimes bend or have a sloppy fit and slip off the nuts. Since you're an ex-auto mechanic, I think you know what I mean.
Agree - Many cheap cone wrenches are made of Chinesium alloy. This alloy has the hardness and wear resistance of Manchego cheese. Buy good stuff and don't encourage the b*****ds who make c**p.

PS Strongly recommend serving Manchego with membrillo (dried quince paste) or Goya guava paste. Mmmmm.
WizardOfBoz is offline  
Likes For WizardOfBoz:
Old 06-23-22, 04:58 PM
  #6  
sean.hwy
Senior Member
Thread Starter
 
sean.hwy's Avatar
 
Join Date: Jan 2020
Location: San Jose
Posts: 1,022

Bikes: Blur / Ibis Hakka MX / team machince alr2 / topstone 1

Mentioned: 1 Post(s)
Tagged: 0 Thread(s)
Quoted: 424 Post(s)
Liked 272 Times in 200 Posts
Thanks guys. Now I know what to search for.
sean.hwy is offline  
Old 06-23-22, 06:46 PM
  #7  
3alarmer 
Friendship is Magic
 
3alarmer's Avatar
 
Join Date: Nov 2010
Location: Sacramento, CA
Posts: 22,930

Bikes: old ones

Mentioned: 304 Post(s)
Tagged: 0 Thread(s)
Quoted: 26243 Post(s)
Liked 10,227 Times in 7,097 Posts
Originally Posted by sean.hwy
Thanks guys. Now I know what to search for.
...if you are going to do much hub repair/overhaul, they come in sets, and the handiest ones (for me) are 13-16mm, with occasional need for 17mm and 18mm.
There are a lot of companies that make and sell an acceptable cone wrench now. I think Pedro's sells them, as well as Park. The Hozan ones are nice. But avoid the "stepped" ones.
__________________
3alarmer is offline  
Likes For 3alarmer:
Old 06-23-22, 07:05 PM
  #8  
Bill Kapaun
Really Old Senior Member
 
Bill Kapaun's Avatar
 
Join Date: Feb 2007
Location: Mid Willamette Valley, Orygun
Posts: 13,822

Bikes: 87 RockHopper,2008 Specialized Globe. Both upgraded to 9 speeds.

Mentioned: 20 Post(s)
Tagged: 0 Thread(s)
Quoted: 1774 Post(s)
Liked 1,230 Times in 851 Posts
Typically I just use a box wrench since 17mm is "typically" a lock nut and doesn't need a thin wrench.
I do own a 17mm, but rarely use it.
Bill Kapaun is offline  
Likes For Bill Kapaun:
Old 06-23-22, 09:21 PM
  #9  
sean.hwy
Senior Member
Thread Starter
 
sean.hwy's Avatar
 
Join Date: Jan 2020
Location: San Jose
Posts: 1,022

Bikes: Blur / Ibis Hakka MX / team machince alr2 / topstone 1

Mentioned: 1 Post(s)
Tagged: 0 Thread(s)
Quoted: 424 Post(s)
Liked 272 Times in 200 Posts
Originally Posted by Bill Kapaun
Typically I just use a box wrench since 17mm is "typically" a lock nut and doesn't need a thin wrench.
I do own a 17mm, but rarely use it.
How does that work? I thought you needed two wrenches. In my case I need one thin 17mm for the bottom nut. the top one I can take off the end cap and my normal wrenches work fine on it.



sean.hwy is offline  
Old 06-23-22, 09:32 PM
  #10  
cxwrench
Senior Member
 
cxwrench's Avatar
 
Join Date: Jul 2013
Location: Nor-Cal
Posts: 3,767

Bikes: lots

Mentioned: 7 Post(s)
Tagged: 0 Thread(s)
Quoted: 1958 Post(s)
Liked 2,932 Times in 1,489 Posts
What do you mean how does it work? Thin wrench on the cone and normal wrench on the locknut, just like any adjustable hub.
cxwrench is offline  
Old 06-23-22, 10:02 PM
  #11  
sean.hwy
Senior Member
Thread Starter
 
sean.hwy's Avatar
 
Join Date: Jan 2020
Location: San Jose
Posts: 1,022

Bikes: Blur / Ibis Hakka MX / team machince alr2 / topstone 1

Mentioned: 1 Post(s)
Tagged: 0 Thread(s)
Quoted: 424 Post(s)
Liked 272 Times in 200 Posts
Originally Posted by cxwrench
What do you mean how does it work? Thin wrench on the cone and normal wrench on the locknut, just like any adjustable hub.
That's how I would do it and why I asked where can I buy a thin wrench.

Originally Posted by Bill Kapaun
Typically I just use a box wrench since 17mm is "typically" a lock nut and doesn't need a thin wrench.
I do own a 17mm, but rarely use it.
Said he does not need a thin wrench. I guess he just uses a single wrench. not sure? that's why I quoted him and asked him how does he do it.
sean.hwy is offline  
Old 06-23-22, 10:15 PM
  #12  
Bill Kapaun
Really Old Senior Member
 
Bill Kapaun's Avatar
 
Join Date: Feb 2007
Location: Mid Willamette Valley, Orygun
Posts: 13,822

Bikes: 87 RockHopper,2008 Specialized Globe. Both upgraded to 9 speeds.

Mentioned: 20 Post(s)
Tagged: 0 Thread(s)
Quoted: 1774 Post(s)
Liked 1,230 Times in 851 Posts
Originally Posted by sean.hwy
How does that work? I thought you needed two wrenches. In my case I need one thin 17mm for the bottom nut. the top one I can take off the end cap and my normal wrenches work fine on it.
I'm talking somewhat older stuff, but you didn't say what you have.
There are very few cones that take a 17mm wrench. They typically take 13-16mm wrenches wheras most (it seems) lock nuts are 17mm.
Since the lock nut is on the end, you don't need a thin wrench. (with the wheel removed).

Your pictures are too close to make sense.
Bill Kapaun is offline  
Old 06-24-22, 12:20 PM
  #13  
sjanzeir
BF's Resident Dumbass
 
sjanzeir's Avatar
 
Join Date: Apr 2016
Location: Jeddah, Saudi Arabia
Posts: 1,566

Bikes: 1990 Raleigh Flyer (size 21"); 2014 Trek 7.6 FX (size 15"); 2014 Trek 7.6 FX (size 17.5"); 2019 Dahon Mu D9; 2020 Dahon Hemingway D9

Mentioned: 6 Post(s)
Tagged: 0 Thread(s)
Quoted: 792 Post(s)
Liked 1,493 Times in 496 Posts
The ones from Icetoolz are nice and reasonably priced..

sjanzeir is offline  
Likes For sjanzeir:
Old 06-27-22, 12:12 PM
  #14  
blinky
senior member
 
Join Date: Oct 2005
Location: Connecticut
Posts: 373

Bikes: 2003 Litespeed Tuscany with Ultegra R-8000 components

Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 145 Post(s)
Liked 40 Times in 35 Posts
Snap On tools make real nice thin stainless wrenches of many different sizes .
blinky is offline  
Likes For blinky:
Old 06-27-22, 01:52 PM
  #15  
Fredo76
The Wheezing Geezer
 
Fredo76's Avatar
 
Join Date: Oct 2021
Location: Española, NM
Posts: 995

Bikes: 1976 Fredo Speciale, Jamis Citizen 1, Ellis-Briggs FAVORI, Rivendell Clem Smith Jr.

Mentioned: 1 Post(s)
Tagged: 0 Thread(s)
Quoted: 393 Post(s)
Liked 854 Times in 421 Posts
I think the long-handled Park cone wrenches with the rubber on the grip end really come in handy when you need that extra leverage. The double-ended, shorter wrenches are the less expensive route. https://www.parktool.com/en-us/category/hub-axle
Fredo76 is offline  
Likes For Fredo76:
Old 06-27-22, 03:47 PM
  #16  
sean.hwy
Senior Member
Thread Starter
 
sean.hwy's Avatar
 
Join Date: Jan 2020
Location: San Jose
Posts: 1,022

Bikes: Blur / Ibis Hakka MX / team machince alr2 / topstone 1

Mentioned: 1 Post(s)
Tagged: 0 Thread(s)
Quoted: 424 Post(s)
Liked 272 Times in 200 Posts
I purchased the park tool cone wrench the other day. thx for your help.


sean.hwy is offline  
Likes For sean.hwy:
Old 06-28-22, 02:03 PM
  #17  
Camilo
Senior Member
 
Join Date: Apr 2007
Posts: 6,760
Mentioned: 10 Post(s)
Tagged: 0 Thread(s)
Quoted: 1106 Post(s)
Liked 1,197 Times in 758 Posts
Every bike shop in the world (maybe I exaggerate) sells "cone wrenches" . Get a variety while you're at it because sure as you-know-what, you'll need a size you don't have. Cheap stamped metal ones work fine for us occasional home mechanics. the Park ones are great, but there are many cheaper alternatives that work fine. To me it's better to have many different sizes, and redundancy, of cheap ones than a few of the nice Park ones. I do have one Park which I bought while traveling and didn't have mine with me, from a shop that only carried them. It's a very nice tool, but doesn't work any better than my little stamped cheap ones. Plus I just don't do much cone adjusting nowadays.
Camilo is offline  
Old 06-28-22, 04:03 PM
  #18  
urbanknight
Over the hill
 
urbanknight's Avatar
 
Join Date: Mar 2006
Location: Los Angeles, CA
Posts: 24,340

Bikes: Giant Defy, Giant Revolt

Mentioned: 1 Post(s)
Tagged: 0 Thread(s)
Quoted: 987 Post(s)
Liked 1,186 Times in 681 Posts
Originally Posted by 3alarmer
...if you are going to do much hub repair/overhaul, they come in sets, and the handiest ones (for me) are 13-16mm, with occasional need for 17mm and 18mm.
There are a lot of companies that make and sell an acceptable cone wrench now. I think Pedro's sells them, as well as Park. The Hozan ones are nice. But avoid the "stepped" ones.
And sometimes you might need two of the same size.
__________________
It's like riding a bicycle
urbanknight is offline  
Likes For urbanknight:
Old 06-28-22, 04:36 PM
  #19  
greatbasin
Full Member
 
Join Date: Mar 2022
Posts: 261
Mentioned: 2 Post(s)
Tagged: 0 Thread(s)
Quoted: 198 Post(s)
Liked 84 Times in 65 Posts
Sheet metal and a file and you can shape one up yourself.
greatbasin is offline  
Old 06-29-22, 06:51 AM
  #20  
smd4
Senior Member
 
Join Date: Dec 2020
Location: Wake Forest, NC
Posts: 5,635

Bikes: 1989 Cinelli Supercorsa

Mentioned: 11 Post(s)
Tagged: 0 Thread(s)
Quoted: 3426 Post(s)
Liked 2,816 Times in 1,716 Posts
Originally Posted by greatbasin
Sheet metal and a file and you can shape one up yourself.
Instead of buying them for a few bucks? Might as well fire up your forge and make your own sheet metal to start with.
smd4 is offline  
Likes For smd4:
Old 06-29-22, 06:53 AM
  #21  
smd4
Senior Member
 
Join Date: Dec 2020
Location: Wake Forest, NC
Posts: 5,635

Bikes: 1989 Cinelli Supercorsa

Mentioned: 11 Post(s)
Tagged: 0 Thread(s)
Quoted: 3426 Post(s)
Liked 2,816 Times in 1,716 Posts
Originally Posted by sean.hwy
That's how I would do it and why I asked where can I buy a thin wrench.

Said he does not need a thin wrench. I guess he just uses a single wrench. not sure? that's why I quoted him and asked him how does he do it.
Don't worry--I understood what you were asking. I thought the same thing.
smd4 is offline  
Old 06-30-22, 05:12 AM
  #22  
Prowler 
Senior Member
 
Join Date: Nov 2013
Location: Near Pottstown, PA: 30 miles NW of Philadelphia
Posts: 2,185

Bikes: 2 Trek Mtn, Cannondale R600 road, 6 vintage road bikes

Mentioned: 83 Post(s)
Tagged: 0 Thread(s)
Quoted: 470 Post(s)
Liked 1,015 Times in 397 Posts
Originally Posted by Camilo
. Cheap stamped metal ones work fine for us occasional home mechanics. the Park ones are great, but there are many cheaper alternatives that work fine.
My experience in three shops has been that the frequency of use (“occasional”) has little to do with it. The strength of the wrench and the tolerances of the wrench are key. Any cone wrench can loosen and tighten a fairly loose lock nut. The test is the really tight fittings that have been unmoved, even corroded for years. As you apply more force to loosen the nut (or to turn the cones away from each other) you apply lots of force to the two “corners” of the flats in the wrench slot. Weaker/value priced wrenches with softer steel can experience damaged slots or spread jaws. Wrenches that we’re not made well may have slots that are too wide: ex 15mm jaw that is too much greater than 15mm. The surplus gap between wrench and fitting speeds the deformation.

These issues exist on any standard open end wrench but those are usually so thick they will survive. Cone wrenches are more vulnerable. At the shop, I see even Park cone wrenches that are deformed as we deal with everything - old wheels, corroded wheels, gorilla overhauled hubs, machine built wheels. SO whether or not the user is occasional or frequent, it’s a matter of the hubs he’s working on and the forces required. I occasionally cold forge the deformations on our anvil to restore a Park wrench but that’s a temporary fix. They are doomed and new ones are ordered. My personal view is that the Park tools are worth the money.
Prowler is online now  
Old 06-30-22, 06:32 AM
  #23  
smd4
Senior Member
 
Join Date: Dec 2020
Location: Wake Forest, NC
Posts: 5,635

Bikes: 1989 Cinelli Supercorsa

Mentioned: 11 Post(s)
Tagged: 0 Thread(s)
Quoted: 3426 Post(s)
Liked 2,816 Times in 1,716 Posts
I use the Park double-enders, linked above. Same ones we used in the shop. The long black ones with the blue handles would look nice hanging on the tool bench though.

Last edited by smd4; 06-30-22 at 11:57 AM.
smd4 is offline  
Old 06-30-22, 11:52 AM
  #24  
Camilo
Senior Member
 
Join Date: Apr 2007
Posts: 6,760
Mentioned: 10 Post(s)
Tagged: 0 Thread(s)
Quoted: 1106 Post(s)
Liked 1,197 Times in 758 Posts
Originally Posted by Prowler
My experience in three shops has been that the frequency of use (“occasional”) has little to do with it. The strength of the wrench and the tolerances of the wrench are key. Any cone wrench can loosen and tighten a fairly loose lock nut. The test is the really tight fittings that have been unmoved, even corroded for years. As you apply more force to loosen the nut (or to turn the cones away from each other) you apply lots of force to the two “corners” of the flats in the wrench slot. Weaker/value priced wrenches with softer steel can experience damaged slots or spread jaws. Wrenches that we’re not made well may have slots that are too wide: ex 15mm jaw that is too much greater than 15mm. The surplus gap between wrench and fitting speeds the deformation.

These issues exist on any standard open end wrench but those are usually so thick they will survive. Cone wrenches are more vulnerable. At the shop, I see even Park cone wrenches that are deformed as we deal with everything - old wheels, corroded wheels, gorilla overhauled hubs, machine built wheels. SO whether or not the user is occasional or frequent, it’s a matter of the hubs he’s working on and the forces required. I occasionally cold forge the deformations on our anvil to restore a Park wrench but that’s a temporary fix. They are doomed and new ones are ordered. My personal view is that the Park tools are worth the money.
No doubt what you said is true. That's why I qualified my comment on the inexpensive ones for occasional home mechanic use. The one Park cone wrench I have is undoubtedly a stronger and more "hand friendly" tool. If I was using them regularly and for stuff you're describing, absolutely a better wrench is needed.
Camilo is offline  
Old 06-30-22, 12:02 PM
  #25  
JohnDThompson 
Old fart
 
JohnDThompson's Avatar
 
Join Date: Nov 2004
Location: Appleton WI
Posts: 24,934

Bikes: Several, mostly not name brands.

Mentioned: 153 Post(s)
Tagged: 0 Thread(s)
Quoted: 3571 Post(s)
Liked 3,366 Times in 1,915 Posts
Originally Posted by greatbasin
Sheet metal and a file and you can shape one up yourself.
Don't expect it to last very long unless you can harden the metal.
JohnDThompson is offline  
Likes For JohnDThompson:

Thread Tools
Search this Thread

Contact Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service -

Copyright © 2024 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.