Go Back  Bike Forums > Bike Forums > Bicycle Mechanics
Reload this Page >

First wheel build- Which used rim: Mavic or Alex?

Notices
Bicycle Mechanics Broken bottom bracket? Tacoed wheel? If you're having problems with your bicycle, or just need help fixing a flat, drop in here for the latest on bicycle mechanics & bicycle maintenance.

First wheel build- Which used rim: Mavic or Alex?

Old 06-01-21, 05:12 PM
  #1  
VicBC_Biker
Senior Member
Thread Starter
 
Join Date: May 2021
Posts: 219
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 111 Post(s)
Liked 69 Times in 51 Posts
First wheel build- Which used rim: Mavic or Alex?

I'm thinking about building a wheel around a dyno hub, using one of the rims from a donor 'set' from a friend.

Rim choices are Mavic A319 622x19 or AlexRims - label is faded but inside rim width is 18mm approximately.

i know next to nothing about wheels, but to my eye the Mavic rims look better.
Mavic A319


AlexRims:



I'd appreciate comments and input. Thanks.

I know it wuld be better to buy a new rim but this plan is for just a cheap experiment.
If it doesn't work out I can re-sell the dyno and chalk it up to experience.
VicBC_Biker is offline  
Old 06-01-21, 05:19 PM
  #2  
cyccommute 
Mad bike riding scientist
 
cyccommute's Avatar
 
Join Date: Nov 2004
Location: Denver, CO
Posts: 27,274

Bikes: Some silver ones, a red one, a black and orange one, and a few titanium ones

Mentioned: 150 Post(s)
Tagged: 1 Thread(s)
Quoted: 6147 Post(s)
Liked 4,092 Times in 2,325 Posts
Originally Posted by VicBC_Biker
I'm thinking about building a wheel around a dyno hub, using one of the rims from a donor 'set' from a friend.

Rim choices are Mavic A319 622x19 or AlexRims - label is faded but inside rim width is 18mm approximately.

i know next to nothing about wheels, but to my eye the Mavic rims look better.
Mavic A319


AlexRims:



I'd appreciate comments and input. Thanks.

I know it wuld be better to buy a new rim but this plan is for just a cheap experiment.
If it doesn't work out I can re-sell the dyno and chalk it up to experience.
It won’t make much difference. I’d probably use the Mavic over the Alex but either would do the job. My concern with the Mavic you’ve shown is that it appears to have holes in it. If they are just scrapes, it will probably be okay. If they holes are actual holes, go with the Alex.
__________________
Stuart Black
Plan Epsilon Around Lake Michigan in the era of Covid
Old School…When It Wasn’t Ancient bikepacking
Gold Fever Three days of dirt in Colorado
Pokin' around the Poconos A cold ride around Lake Erie
Dinosaurs in Colorado A mountain bike guide to the Purgatory Canyon dinosaur trackway
Solo Without Pie. The search for pie in the Midwest.
Picking the Scablands. Washington and Oregon, 2005. Pie and spiders on the Columbia River!



cyccommute is offline  
Likes For cyccommute:
Old 06-01-21, 05:35 PM
  #3  
Bill Kapaun
Really Old Senior Member
 
Bill Kapaun's Avatar
 
Join Date: Feb 2007
Location: Mid Willamette Valley, Orygun
Posts: 13,822

Bikes: 87 RockHopper,2008 Specialized Globe. Both upgraded to 9 speeds.

Mentioned: 20 Post(s)
Tagged: 0 Thread(s)
Quoted: 1774 Post(s)
Liked 1,230 Times in 851 Posts
Take a micrometer and measure the brake track thickness.

I'd probably disassemble both wheels and compare the bare rims for trueness.
The straighter the rim, the easier the build.
Bill Kapaun is offline  
Likes For Bill Kapaun:
Old 06-01-21, 07:25 PM
  #4  
Andrew R Stewart 
Senior Member
 
Andrew R Stewart's Avatar
 
Join Date: Feb 2012
Location: Rochester, NY
Posts: 18,003

Bikes: Stewart S&S coupled sport tourer, Stewart Sunday light, Stewart Commuting, Stewart Touring, Co Motion Tandem, Stewart 3-Spd, Stewart Track, Fuji Finest, Mongoose Tomac ATB, GT Bravado ATB, JCP Folder, Stewart 650B ATB

Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 4172 Post(s)
Liked 3,791 Times in 2,270 Posts
Two good replies! My initial preference is the Mavic rim. If nothing but due to the machined brake track. Andy
__________________
AndrewRStewart
Andrew R Stewart is offline  
Likes For Andrew R Stewart:
Old 06-01-21, 07:43 PM
  #5  
thook
(rhymes with spook)
 
thook's Avatar
 
Join Date: Aug 2009
Location: Winslow, AR
Posts: 2,795

Bikes: '83 univega gran turismo x2, '85 schwinn super le tour,'89 miyata triple cross, '91 GT tequesta, '90 yokota grizzly peak, '94 GT backwoods, '95'ish scott tampico, '98 bonty privateer, '93 mongoose crossway 625, '98 parkpre ariel, 2k'ish giant fcr3

Mentioned: 26 Post(s)
Tagged: 0 Thread(s)
Quoted: 919 Post(s)
Liked 745 Times in 546 Posts
both rims are of good quality, but i think mr. stewart nailed it with the mavic machined sidewall. it really does make a difference
thook is offline  
Old 06-02-21, 10:08 AM
  #6  
urbanknight
Over the hill
 
urbanknight's Avatar
 
Join Date: Mar 2006
Location: Los Angeles, CA
Posts: 24,340

Bikes: Giant Defy, Giant Revolt

Mentioned: 1 Post(s)
Tagged: 0 Thread(s)
Quoted: 987 Post(s)
Liked 1,186 Times in 681 Posts
Originally Posted by Bill Kapaun
I'd probably disassemble both wheels and compare the bare rims for trueness.
The straighter the rim, the easier the build.
If you have access to a glass table top, you can lay the rims down on it to see how true they are.
__________________
It's like riding a bicycle
urbanknight is offline  
Old 06-02-21, 10:22 AM
  #7  
Bill Kapaun
Really Old Senior Member
 
Bill Kapaun's Avatar
 
Join Date: Feb 2007
Location: Mid Willamette Valley, Orygun
Posts: 13,822

Bikes: 87 RockHopper,2008 Specialized Globe. Both upgraded to 9 speeds.

Mentioned: 20 Post(s)
Tagged: 0 Thread(s)
Quoted: 1774 Post(s)
Liked 1,230 Times in 851 Posts
Originally Posted by urbanknight
If you have access to a glass table top, you can lay the rims down on it to see how true they are.
And it has to be a glass table top because???
Bill Kapaun is offline  
Old 06-02-21, 10:52 AM
  #8  
urbanknight
Over the hill
 
urbanknight's Avatar
 
Join Date: Mar 2006
Location: Los Angeles, CA
Posts: 24,340

Bikes: Giant Defy, Giant Revolt

Mentioned: 1 Post(s)
Tagged: 0 Thread(s)
Quoted: 987 Post(s)
Liked 1,186 Times in 681 Posts
Originally Posted by Bill Kapaun
And it has to be a glass table top because???
Glass table tops are either flat or shattered. Other materials can have imperfections or warpage, although granite/marble/etc. would probably be close enough... or a surface plate if you have one.
__________________
It's like riding a bicycle

Last edited by urbanknight; 06-02-21 at 10:57 AM.
urbanknight is offline  
Likes For urbanknight:
Old 06-02-21, 02:01 PM
  #9  
dsbrantjr
Senior Member
 
dsbrantjr's Avatar
 
Join Date: Sep 2010
Location: Roswell, GA
Posts: 8,319

Bikes: '93 Trek 750, '92 Schwinn Crisscross, '93 Mongoose Alta

Mentioned: 30 Post(s)
Tagged: 0 Thread(s)
Quoted: 1438 Post(s)
Liked 1,092 Times in 723 Posts
Originally Posted by urbanknight
If you have access to a glass table top, you can lay the rims down on it to see how true they are.
Yeah, all else being equal, build up the straightest one.
dsbrantjr is offline  
Old 06-02-21, 02:12 PM
  #10  
gearbasher
Senior Member
 
gearbasher's Avatar
 
Join Date: May 2009
Location: Sitting on my butt in front of a computer
Posts: 1,535
Mentioned: 15 Post(s)
Tagged: 0 Thread(s)
Quoted: 439 Post(s)
Liked 834 Times in 363 Posts
I've built wheels using both Mavic and Alex rims. My opinion is based on using new rims. The Mavic rims definitely were easier to build. After bringing the spokes up to equal tension, the Mavic rims were needed a lot less truing on the stand than the Alex rims.
gearbasher is offline  
Old 06-02-21, 02:56 PM
  #11  
VicBC_Biker
Senior Member
Thread Starter
 
Join Date: May 2021
Posts: 219
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 111 Post(s)
Liked 69 Times in 51 Posts
Originally Posted by cyccommute
My concern with the Mavic you’ve shown is that it appears to have holes in it. If they are just scrapes, it will probably be okay. If they holes are actual holes, go with the Alex.
Thanks.
I hadn't even noticed those marks in the label area. I just checked - one mark was just a wrinkle in the label and the other is a slight scuff in the rim with the label wrinkled up around it.
So I think it will be OK.
I think using the Mavic with the full eyelets might be easier for me as a rookie? No chance of dropping a nipple into the rim?
VicBC_Biker is offline  
Old 06-02-21, 03:00 PM
  #12  
VicBC_Biker
Senior Member
Thread Starter
 
Join Date: May 2021
Posts: 219
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 111 Post(s)
Liked 69 Times in 51 Posts
Thanks for all the replies.
I've ordered the hub and once I have that here, I'll do some measurements and order spokes and nipples.
I guess I can 'unbuild' the wheel(s) while I'm waiting.

Any recommendatins for a spoke supplier? (I'm in Canada so shipping can be an issue but a spoke supplier local to me is charging twice to three times the US prices I've seen...so I'm wide open to alternatives.)
VicBC_Biker is offline  
Old 06-02-21, 03:10 PM
  #13  
Crankycrank
Senior Member
 
Join Date: Jan 2009
Location: San Diego, CA
Posts: 3,649
Mentioned: 10 Post(s)
Tagged: 0 Thread(s)
Quoted: 835 Post(s)
Liked 1,053 Times in 739 Posts
Originally Posted by VicBC_Biker
I think using the Mavic with the full eyelets might be easier for me as a rookie? No chance of dropping a nipple into the rim?
An old trick is to just thread an old spoke into the nipple head from the head side several turns and use the spoke to feed the nipple into the hole.
Crankycrank is offline  
Likes For Crankycrank:
Old 06-02-21, 03:47 PM
  #14  
Broctoon
Super-duper Genius
 
Broctoon's Avatar
 
Join Date: Aug 2016
Location: Muskrat Springs, Utah
Posts: 1,713
Mentioned: 20 Post(s)
Tagged: 0 Thread(s)
Quoted: 768 Post(s)
Liked 983 Times in 508 Posts
I’ve only built 3 or 4 wheels, but getting ready to do a few more. It’s easier than you might think and can be very rewarding.

My advice is to take your time. Read through Sheldon Brown’s online instructions completely before getting started, and then have them ready to consult once you’re underway. If you can have a complete wheel to look at as you go, with the same spoke count and cross pattern as your new build, that helps.

i don’t have anything to offer that wasn’t already stated regarding your two rim choices.

Modern Bike has a good selection of spokes. Harris Cycles does too, and I like supporting them. Retrogression is my favorite source for fixed gear and single speed parts, and of course spokes don’t care how many gears you have, so this shop is another good source.

Though they they cost a little more, butted spokes are recommended, because they make a more durable wheel. If you use deeply butted spokes—like Sapim Laser (2.0 / 1.5 / 2.0)—you must be careful to not wind them up. I just twist 1/8 or 1/4 of a turn when truing and tensioning, and then back off again half that far each time.

If your first wheel is a front, that will give you an easy introduction, and then you can move to a rear next.
Broctoon is offline  
Old 06-02-21, 04:04 PM
  #15  
Bill Kapaun
Really Old Senior Member
 
Bill Kapaun's Avatar
 
Join Date: Feb 2007
Location: Mid Willamette Valley, Orygun
Posts: 13,822

Bikes: 87 RockHopper,2008 Specialized Globe. Both upgraded to 9 speeds.

Mentioned: 20 Post(s)
Tagged: 0 Thread(s)
Quoted: 1774 Post(s)
Liked 1,230 Times in 851 Posts
Originally Posted by Broctoon
......Though they they cost a little more, butted spokes are recommended, because they make a more durable wheel. If you use deeply butted spokes—like Sapim Laser (2.0 / 1.5 / 2.0)—you must be careful to not wind them up. I just twist 1/8 or 1/4 of a turn when truing and tensioning, and then back off again half that far each time.

If your first wheel is a front, that will give you an easy introduction, and then you can move to a rear next.
Although I prefer butted spokes, these are USED RIMS.

I would NOT use 1.5mm spoke on the DS. The DS tension is getting mighty close to the point that you can't add more tension. The spoke will just stretch & stretch and.....
Remember, this is a newbie assembling this wheel. A little "cushion" for mistakes is a good idea.
My typical choice is 14/15ga. DS and a thinner spoke on the NDS. 1.6-1.7mm in the "thin" section.

I find a rear wheel MUCH easier. You basically build the DS and just tension the NDS for proper dish.
Bill Kapaun is offline  
Old 06-02-21, 04:27 PM
  #16  
VicBC_Biker
Senior Member
Thread Starter
 
Join Date: May 2021
Posts: 219
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 111 Post(s)
Liked 69 Times in 51 Posts
Thanks for all the info; I appreciate it.
I've bought Musson's book, and it seems good. Well-written and clear.
https://www.wheelpro.co.uk/wheelbuilding/book.php

This wheel will be a front with disk brake hub, so some of the same asymmetry as a rear wheel. Looking forward to it!
VicBC_Biker is offline  
Old 06-02-21, 04:49 PM
  #17  
rmacdona
Newbie
 
Join Date: May 2019
Location: Waterdown, Ontario
Posts: 24

Bikes: 1987 Cannondale ST600, 1988 Fisher Mt. Tam, 1989 Cannondale SR800, 1998 Cannondale T500

Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 4 Post(s)
Liked 8 Times in 6 Posts
For spokes and nipples you might want to take a look at BIKE24 from Germany. They have DT Swiss and Sapim available at reasonable prices.
rmacdona is offline  
Old 06-02-21, 09:07 PM
  #18  
Broctoon
Super-duper Genius
 
Broctoon's Avatar
 
Join Date: Aug 2016
Location: Muskrat Springs, Utah
Posts: 1,713
Mentioned: 20 Post(s)
Tagged: 0 Thread(s)
Quoted: 768 Post(s)
Liked 983 Times in 508 Posts
Originally Posted by Bill Kapaun
Although I prefer butted spokes, these are USED RIMS.

I would NOT use 1.5mm spoke on the DS. The DS tension is getting mighty close to the point that you can't add more tension. The spoke will just stretch & stretch and.....
Remember, this is a newbie assembling this wheel. A little "cushion" for mistakes is a good idea.
My typical choice is 14/15ga. DS and a thinner spoke on the NDS. 1.6-1.7mm in the "thin" section.

I find a rear wheel MUCH easier. You basically build the DS and just tension the NDS for proper dish.
All good pointers, for both the OP and me, also a newbie wheelsmith. I’ve used DT 2 / 1.8 / 2 in the past and got wheels that stayed true and strong. My next front will have the Sapim Lasers, but the rear to go with it is getting Sapim Race. It’s a fixed gear, double threaded hub, so dishing is not an issue and the left & right side will have equal length and equal tension spokes, like a front.
Broctoon is offline  
Old 06-02-21, 09:29 PM
  #19  
cyccommute 
Mad bike riding scientist
 
cyccommute's Avatar
 
Join Date: Nov 2004
Location: Denver, CO
Posts: 27,274

Bikes: Some silver ones, a red one, a black and orange one, and a few titanium ones

Mentioned: 150 Post(s)
Tagged: 1 Thread(s)
Quoted: 6147 Post(s)
Liked 4,092 Times in 2,325 Posts
Originally Posted by VicBC_Biker
Thanks.
I hadn't even noticed those marks in the label area. I just checked - one mark was just a wrinkle in the label and the other is a slight scuff in the rim with the label wrinkled up around it.
So I think it will be OK.
I think using the Mavic with the full eyelets might be easier for me as a rookie? No chance of dropping a nipple into the rim?
Yes, the eyelets prevent dropping a nipple into the rim but that’s not a huge problem in general. A dropped nipple will come out but you have to do a bit of shaking to get it out. They tend to rattle around if you forget to get them out...I know from experience.

Originally Posted by VicBC_Biker
Thanks for all the replies.
I've ordered the hub and once I have that here, I'll do some measurements and order spokes and nipples.
I guess I can 'unbuild' the wheel(s) while I'm waiting.

Any recommendatins for a spoke supplier? (I'm in Canada so shipping can be an issue but a spoke supplier local to me is charging twice to three times the US prices I've seen...so I'm wide open to alternatives.)
Others have suggested Rose Bikes out of Germany. Rose sells spokes for less then you can get them wholesale in the US. Shipping is reasonable and quick. I would suggest double butted (or triple if you are a heavier rider or are planning on heavier loads). The rim is secondary to the life of a wheel. Spokes are more important. Spend money on them.
__________________
Stuart Black
Plan Epsilon Around Lake Michigan in the era of Covid
Old School…When It Wasn’t Ancient bikepacking
Gold Fever Three days of dirt in Colorado
Pokin' around the Poconos A cold ride around Lake Erie
Dinosaurs in Colorado A mountain bike guide to the Purgatory Canyon dinosaur trackway
Solo Without Pie. The search for pie in the Midwest.
Picking the Scablands. Washington and Oregon, 2005. Pie and spiders on the Columbia River!



cyccommute is offline  
Likes For cyccommute:
Old 06-03-21, 07:05 AM
  #20  
L134 
Senior Member
 
Join Date: Dec 2015
Location: San Diego
Posts: 704

Bikes: 1978 Bruce Gordon, 1977 Lippy, 199? Lippy tandem, Bike Friday NWT, 1982 Trek 720, 2012 Rivendell Atlantis, 1983 Bianchi Specialissima?

Mentioned: 11 Post(s)
Tagged: 0 Thread(s)
Quoted: 345 Post(s)
Liked 170 Times in 105 Posts
Originally Posted by VicBC_Biker
I'm thinking about building a wheel around a dyno hub, using one of the rims from a donor 'set' from a friend.

Rim choices are Mavic A319 622x19 or AlexRims - label is faded but inside rim width is 18mm approximately.

i know next to nothing about wheels, but to my eye the Mavic rims look better.
Mavic A319


AlexRims:


I'd appreciate comments and input. Thanks.

I know it wuld be better to buy a new rim but this plan is for just a cheap experiment.
If it doesn't work out I can re-sell the dyno and chalk it up to experience.
budget wheel
front wheel
dynamo hub

Unless you have a history of trashing well built wheels, save your money and use straight gauge spokes. Budget build - butted spokes are considerably more expensive. Dynamo hub - this isn't a weight weenie build. Front wheel - how many people have broken spokes on their front wheel? I use straight gauge without any issues on rear wheels. I'm not arguing that butted aren't stronger and all that, just that straight gauge is perfectly adequate unless you are experiencing a lot of spoke failures. Even then, my guess is poor builds not straight gauge spokes.
L134 is offline  
Old 06-03-21, 07:46 AM
  #21  
Broctoon
Super-duper Genius
 
Broctoon's Avatar
 
Join Date: Aug 2016
Location: Muskrat Springs, Utah
Posts: 1,713
Mentioned: 20 Post(s)
Tagged: 0 Thread(s)
Quoted: 768 Post(s)
Liked 983 Times in 508 Posts
Originally Posted by L134
Budget build - butted spokes are considerably more expensive.

Dynamo hub - this isn't a weight weenie build.
1. You call 30 or 40 cents apiece considerable? On a 32 spoke wheel, it’s like ten bucks more.

2. The point of butted spokes isn’t just to save a few grams. It’s about making the wheel more durable.

I mean, you’re not wrong in your comments. I can’t speak for the OP, but for my money butted spokes are a worthwhile upgrade.
Broctoon is offline  
Old 06-03-21, 08:39 AM
  #22  
L134 
Senior Member
 
Join Date: Dec 2015
Location: San Diego
Posts: 704

Bikes: 1978 Bruce Gordon, 1977 Lippy, 199? Lippy tandem, Bike Friday NWT, 1982 Trek 720, 2012 Rivendell Atlantis, 1983 Bianchi Specialissima?

Mentioned: 11 Post(s)
Tagged: 0 Thread(s)
Quoted: 345 Post(s)
Liked 170 Times in 105 Posts
Originally Posted by Broctoon
1. You call 30 or 40 cents apiece considerable? On a 32 spoke wheel, it’s like ten bucks more.

2. The point of butted spokes isn’t just to save a few grams. It’s about making the wheel more durable.

I mean, you’re not wrong in your comments. I can’t speak for the OP, but for my money butted spokes are a worthwhile upgrade.
I understand but I see used rim, experimental build, front wheel - why spend the $10? I’m an accountant, 30-40% more expensive is something if it is for overkill. But for the parameters mentioned, I wouldn’t have commented.
L134 is offline  
Old 06-03-21, 09:24 AM
  #23  
VicBC_Biker
Senior Member
Thread Starter
 
Join Date: May 2021
Posts: 219
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 111 Post(s)
Liked 69 Times in 51 Posts
About double-butted vs plain spokes...thanks for those ideas and thoughts; I appreciate them.
I think I read somewhere that it's as easy (or easier) to build with the DB spokes.
The basic spoke cost isn't such a big issue. If you check my other thread on 'Spoke Source' you can see that (since I'm in Canada) the shipping cost can be as much as the cost for the spokes themselves.

All 'food for thought'.

If I really want to practice, I can just unlace and rebuild one of the rims, re-using the spokes. If I get bored, I may well do that!
VicBC_Biker is offline  
Old 06-03-21, 10:00 AM
  #24  
Broctoon
Super-duper Genius
 
Broctoon's Avatar
 
Join Date: Aug 2016
Location: Muskrat Springs, Utah
Posts: 1,713
Mentioned: 20 Post(s)
Tagged: 0 Thread(s)
Quoted: 768 Post(s)
Liked 983 Times in 508 Posts
Originally Posted by L134
I understand but I see used rim, experimental build, front wheel - why spend the $10? I’m an accountant, 30-40% more expensive is something if it is for overkill. But for the parameters mentioned, I wouldn’t have commented.
Your strategy is certainly valid. I’ve contemplated the question myself when planning a wheel build. I tend to default to the nicer components anytime the cost difference is low to moderate (from the perspective of someone living in the first world and making a decent income). I’m sure I’ve spent hundreds—probably thousands—of dollars over the years, 20 to 50 dollars at a time, on bike stuff that offered little real benefit.
Broctoon is offline  
Old 06-03-21, 10:07 AM
  #25  
cyccommute 
Mad bike riding scientist
 
cyccommute's Avatar
 
Join Date: Nov 2004
Location: Denver, CO
Posts: 27,274

Bikes: Some silver ones, a red one, a black and orange one, and a few titanium ones

Mentioned: 150 Post(s)
Tagged: 1 Thread(s)
Quoted: 6147 Post(s)
Liked 4,092 Times in 2,325 Posts
Originally Posted by L134
I understand but I see used rim, experimental build, front wheel - why spend the $10? I’m an accountant, 30-40% more expensive is something if it is for overkill. But for the parameters mentioned, I wouldn’t have commented.
Look at it this way: If the wheel build works, and you end up keeping it, the double butted spokes will give a better return in the long run. If you build the wheel with straight gauge spokes, you might end up rebuilding in the future and end up spending money twice. Nothing is more expensive then the tool you have to buy twice.
__________________
Stuart Black
Plan Epsilon Around Lake Michigan in the era of Covid
Old School…When It Wasn’t Ancient bikepacking
Gold Fever Three days of dirt in Colorado
Pokin' around the Poconos A cold ride around Lake Erie
Dinosaurs in Colorado A mountain bike guide to the Purgatory Canyon dinosaur trackway
Solo Without Pie. The search for pie in the Midwest.
Picking the Scablands. Washington and Oregon, 2005. Pie and spiders on the Columbia River!



cyccommute is offline  

Thread Tools
Search this Thread

Contact Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service -

Copyright © 2024 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.