Can I change wheel sizes?
#1
Junior Member
Thread Starter
Can I change wheel sizes?
I have a Cannondale F5 mountain bike with 26" wheels and disc brakes. I have been searching unsuccessfully for a spare wheelset so I can have slicks on one and knobbies on the other. 27.5" rims are everywhere it seems, so I was wondering if it's feasible to get slicks for that size, and mount them? I don't have a set handy to try, and don't want to buy some just to see, so I figured I'd ask here.
Eric
Eric
Last edited by exercion; 07-11-21 at 05:29 PM.
#2
Senior Member
Join Date: Aug 2005
Location: Pittsburgh, PA
Posts: 33,656
Bikes: '96 Litespeed Catalyst, '05 Litespeed Firenze, '06 Litespeed Tuscany, '20 Surly Midnight Special, All are 3x10. It is hilly around here!
Mentioned: 39 Post(s)
Tagged: 0 Thread(s)
Quoted: 2026 Post(s)
Likes: 0
Liked 1,096 Times
in
742 Posts
It's unlikely a 27.5" wheel and tire will fit in a frame designed for 26" wheels as there probably isn't enough frame and fork clearance. Many bikes built for 700c (aka 29") wheels will take 27.5" wheels and vice-versa but not those for 26" wheels.
Last edited by HillRider; 07-11-21 at 05:16 PM.
#3
Junior Member
Thread Starter
Eric
#4
Senior Member
Join Date: Feb 2017
Location: Northern Shenandoah Valley
Posts: 4,140
Bikes: More bikes than riders
Mentioned: 36 Post(s)
Tagged: 0 Thread(s)
Quoted: 1444 Post(s)
Liked 761 Times
in
569 Posts
A 26x2" tire is nominally about 660mm in diameter. A 42mm tire designed for a 27.5" wheel (584mm) is about 668mm in diameter. If your frame has plenty of clearance for a nominal 26x2" tire, then I think you'd be able to fit a 42-584 tire.
Likes For hokiefyd:
#5
Senior member
Join Date: Oct 2004
Location: Oakville Ontario
Posts: 8,117
Mentioned: 25 Post(s)
Tagged: 0 Thread(s)
Quoted: 943 Post(s)
Liked 658 Times
in
371 Posts
A few quick measurements, or a test wheel set fitting will soon tell the tale.
In fact, I have done one 26" to 29er conversion. It put the crank higher than I would have liked, but it's what the customer wanted, and the bike had the clearance. Not many have that much though.
#6
Senior Member
Join Date: Nov 2014
Location: Eugene, Oregon, USA
Posts: 27,547
Mentioned: 217 Post(s)
Tagged: 0 Thread(s)
Quoted: 18372 Post(s)
Liked 4,507 Times
in
3,350 Posts
26" rims and wheels should be everywhere, but not necessarily high quality with discs.
For 650b, a lot will depend on tire width.
I did a 26" to 700c conversion a while ago. Going from standard 26" to narrow 700c. It worked reasonably well, although the frame dimensions were a bit off.
For 650b, a lot will depend on tire width.
I did a 26" to 700c conversion a while ago. Going from standard 26" to narrow 700c. It worked reasonably well, although the frame dimensions were a bit off.
Likes For CliffordK:
#7
Senior Member
Join Date: Aug 2005
Location: Pittsburgh, PA
Posts: 33,656
Bikes: '96 Litespeed Catalyst, '05 Litespeed Firenze, '06 Litespeed Tuscany, '20 Surly Midnight Special, All are 3x10. It is hilly around here!
Mentioned: 39 Post(s)
Tagged: 0 Thread(s)
Quoted: 2026 Post(s)
Likes: 0
Liked 1,096 Times
in
742 Posts
#8
Senior Member
Join Date: Mar 2008
Posts: 8,688
Mentioned: 46 Post(s)
Tagged: 0 Thread(s)
Quoted: 1074 Post(s)
Liked 295 Times
in
222 Posts
I have a Cannondale F5 mountain bike with 26" wheels and disc brakes. I have been searching unsuccessfully for a spare wheelset so I can have slicks on one and knobbies on the other. 27.5" rims are everywhere it seems, so I was wondering if it's feasible to get slicks for that size, and mount them? I don't have a set handy to try, and don't want to buy some just to see, so I figured I'd ask here.
Eric
Eric
Many who started riding during the 26” era still have some wheels left. If you’d been local I could have given you a pair.
2) how wide do you want those slicks?
27.5” is also known as 650B, these have the same Bead Seat Diameter, where rim and tire overlap. If you’re OK with a narrower tire, there should be a decent selection of slicks for that size, which would leave the OD about the same.
#9
Senior Member
Here's an example of a direct swap from 26" MTB to 700C road wheel/tire:
https://www.mtbr.com/threads/is-a-ri...3/post-9683247
Last edited by hydrocarbon; 07-12-21 at 01:39 AM.
#10
Junior Member
Thread Starter
Dude, it'll work 100% fine and roll better than 26" wheels if we're talking mid-width slicks. People have been using road and cyclocross tires on 700C wheels with 26" disc frames for ages; there's tons of clearance for a 27.5".
Here's an example of a direct swap from 26" MTB to 700C road wheel/tire:
https://www.mtbr.com/threads/is-a-ri...3/post-9683247
Here's an example of a direct swap from 26" MTB to 700C road wheel/tire:
https://www.mtbr.com/threads/is-a-ri...3/post-9683247
Eric
Likes For exercion:
#11
Junior Member
Thread Starter
1) where have you been looking?
Many who started riding during the 26” era still have some wheels left. If you’d been local I could have given you a pair.
2) how wide do you want those slicks?
27.5” is also known as 650B, these have the same Bead Seat Diameter, where rim and tire overlap. If you’re OK with a narrower tire, there should be a decent selection of slicks for that size, which would leave the OD about the same.
Many who started riding during the 26” era still have some wheels left. If you’d been local I could have given you a pair.
2) how wide do you want those slicks?
27.5” is also known as 650B, these have the same Bead Seat Diameter, where rim and tire overlap. If you’re OK with a narrower tire, there should be a decent selection of slicks for that size, which would leave the OD about the same.
#12
Senior Member
Join Date: Jan 2013
Location: South Jersey
Posts: 2,265
Mentioned: 18 Post(s)
Tagged: 0 Thread(s)
Quoted: 714 Post(s)
Liked 800 Times
in
475 Posts
They aren't that hard to find. Here is a whole page of them https://www.universalcycles.com/shop...?category=5479 If you were near me, I'd give you a pair, since I have several pairs that I'm no longer using.
#13
Senior Member
Join Date: Jun 2002
Location: Montreal, Quebec
Posts: 5,925
Mentioned: 16 Post(s)
Tagged: 0 Thread(s)
Quoted: 1818 Post(s)
Liked 1,693 Times
in
974 Posts
One area that could be a problem is if your current wheels use quick releases rather than thru axles. Some thru axle wheels can be converted to quick release but many others can not so that is another consideration
#14
Senior Member
I've converted old 26" mountain bikes with 700c and 650b wheelsets. 700x23 roadie tires fit fine and so do 650bx47 tires with knobbier tires. Do it.
Likes For commo_soulja:
#15
Senior Member
Join Date: Mar 2019
Posts: 1,606
Mentioned: 8 Post(s)
Tagged: 0 Thread(s)
Quoted: 581 Post(s)
Liked 921 Times
in
518 Posts
There are still many 26" rims of good quality available, many good quality hubs available, and good quality spokes available. I know it is not the most common way to get good wheels, but building or having your own built is still an option.