Go Back  Bike Forums > Bike Forums > Tandem Cycling
Reload this Page >

Cannondale Tandem Conversion to DI2 11 Speed

Notices
Tandem Cycling A bicycle built for two. Want to find out more about this wonderful world of tandems? Check out this forum to talk with other tandem enthusiasts. Captains and stokers welcome!

Cannondale Tandem Conversion to DI2 11 Speed

Old 02-12-17, 10:43 AM
  #1  
Fergp
Newbie
Thread Starter
 
Join Date: May 2014
Posts: 13
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 7 Post(s)
Likes: 0
Liked 3 Times in 2 Posts
Cannondale Tandem Conversion to DI2 11 Speed

I just finished my winter project; converting our 2015 Cannondale Road Tandem 2 to DI2 11 speed! I received a lot of help from this form, so I wanted to share the result. Here are a few key points to this project:

• I built the configuration around the 11-40 XT Shimano cassette since it is one the few 11 speed cassettes that work with a 10 speed wheel. This bike has DT Swiss 540 hubs and can't use a normal 11 speed road cassette.

• I used a Wolf Tooth Road Link to extend the Ultegra 6870 GS rear derailleur to 40 tooth capacity.

• I moved the 52 tooth chainring to the middle position and found a 38 tooth 74 BCD chainring on eBay to replace the granny gear. I then added a chainring guard to the outer position to make it look cool!

• I added the D-Fly DI2 wireless module, so I see the current gear selection on my Garmin display. The Garmin also shows the DI2 battery charge level and pops up a warning when the charge goes below 20%.

We are waiting for nicer weather before we take our first ride, but shifting performance on the stand is quick, clean and precise. There is no hesitation on any shifts either up or down. My configuration exceeds the chain wrap capacity so I can’t use the 52 – 40 gear, but that is not a practical gear to use anyhow, so I’m not too concerned. Thanks for everyone’s help!
Attached Images
File Type: jpg
di1.jpg (42.8 KB, 633 views)
File Type: jpg
di2.jpg (44.0 KB, 622 views)
File Type: jpg
di3.jpg (40.8 KB, 615 views)
File Type: jpg
di4.jpg (22.5 KB, 593 views)
File Type: jpg
di7.jpg (23.5 KB, 601 views)
Fergp is offline  
Likes For Fergp:
Old 02-12-17, 11:41 PM
  #2  
B. Carfree
Senior Member
 
Join Date: Jan 2010
Location: Eugene, Oregon
Posts: 7,048
Mentioned: 10 Post(s)
Tagged: 0 Thread(s)
Quoted: 509 Post(s)
Likes: 0
Liked 9 Times in 8 Posts
Looks awesome. Did you consider moving the timing chain to the drive side?
B. Carfree is offline  
Old 04-07-17, 09:02 AM
  #3  
ds31
Newbie
 
Join Date: Apr 2017
Posts: 1
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 1 Post(s)
Likes: 0
Liked 0 Times in 0 Posts
Nicely done! I am considering doing the same thing with my Co-Motion tandem, either with Di2 or Sram eTap wireless. I cannot tell from your photos where you installed the battery or the wire layout on the bike. Do you have any other photos showing that?
ds31 is offline  
Old 04-14-17, 04:57 AM
  #4  
Fergp
Newbie
Thread Starter
 
Join Date: May 2014
Posts: 13
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 7 Post(s)
Likes: 0
Liked 3 Times in 2 Posts
Here are a few more pictures. I fabricated an extension to the standard battery mount to make it fit the water bottle mount on the bottom of the down tube. I decided to stay with the old-style battery to match the other three DI2 setups we have in the family! This also meant that I could not use the newer Bluetooth version of the D-Fly transmitter due to compatibility issues. The old model (SM-EWW01) was hard to find. Also, the older style battery and wire harness are less expensive and keep me close to my $1000 budget for this project.
We now have about 8 rides on the new set up and absolutely love it! The shifting is crisp and precise at every position. I also like the simplicity of the double up front vs. the old triple!
Attached Images
File Type: jpg
DIT1.jpg (72.0 KB, 544 views)
File Type: jpg
DIT2.jpg (40.1 KB, 541 views)
File Type: jpg
DIT3.jpg (44.1 KB, 539 views)
File Type: jpg
DIT4.jpg (48.6 KB, 546 views)

Last edited by Fergp; 04-14-17 at 05:57 AM.
Fergp is offline  
Old 04-18-17, 11:02 PM
  #5  
ahultin
Senior Member
 
ahultin's Avatar
 
Join Date: May 2007
Location: Bonsall, Ca
Posts: 679

Bikes: 2003 Cannondale Jekyll 1000, 2014 Fuji Finest 1.5 (wife), 2008 Fuji Finest 1.0 (Daughter), 2012 Fuji Cross 2.0 (son), 2011 Cannondale Road Tandem 2

Mentioned: 7 Post(s)
Tagged: 0 Thread(s)
Quoted: 57 Post(s)
Liked 27 Times in 17 Posts
Thank you, very helpful!
ahultin is offline  
Old 04-19-17, 09:07 AM
  #6  
merlinextraligh
pan y agua
 
merlinextraligh's Avatar
 
Join Date: Aug 2005
Location: Jacksonville
Posts: 31,273

Bikes: Willier Zero 7; Merlin Extralight; Calfee Dragonfly tandem, Calfee Adventure tandem; Cervelo P2; Motebecane Ti Fly 29er; Motebecanne Phantom Cross; Schwinn Paramount Track bike

Mentioned: 17 Post(s)
Tagged: 0 Thread(s)
Quoted: 1428 Post(s)
Liked 697 Times in 353 Posts
Originally Posted by ds31
Nicely done! I am considering doing the same thing with my Co-Motion tandem, either with Di2 or Sram eTap wireless.

IMHO, Electronic shifting makes a huge difference on a tandem.

With the longer cable runs, and the torque of two riders, cable actuated shifting on tandems always leaves a little to be desired.

Di2 on a tandem shifts perfectly.
__________________
You could fall off a cliff and die.
You could get lost and die.
You could hit a tree and die.
OR YOU COULD STAY HOME AND FALL OFF THE COUCH AND DIE.
merlinextraligh is offline  
Old 04-19-17, 09:10 AM
  #7  
merlinextraligh
pan y agua
 
merlinextraligh's Avatar
 
Join Date: Aug 2005
Location: Jacksonville
Posts: 31,273

Bikes: Willier Zero 7; Merlin Extralight; Calfee Dragonfly tandem, Calfee Adventure tandem; Cervelo P2; Motebecane Ti Fly 29er; Motebecanne Phantom Cross; Schwinn Paramount Track bike

Mentioned: 17 Post(s)
Tagged: 0 Thread(s)
Quoted: 1428 Post(s)
Liked 697 Times in 353 Posts
Originally Posted by Fergp
. My configuration exceeds the chain wrap capacity so I can’t use the 52 – 40 gear, but that is not a practical gear to use anyhow, so I’m not too concerned. Thanks for everyone’s help!

I'd resize the chain. Far better to have too much chain so it wont wrap in the small/small combination, than not enough to go in the big/big.

Someday you'll inadvertently shift into the big/big, and it can be a very expensive misshift.
__________________
You could fall off a cliff and die.
You could get lost and die.
You could hit a tree and die.
OR YOU COULD STAY HOME AND FALL OFF THE COUCH AND DIE.
merlinextraligh is offline  
Likes For merlinextraligh:
Old 04-19-17, 09:24 AM
  #8  
Dan333SP
Serious Cyclist
 
Dan333SP's Avatar
 
Join Date: Aug 2011
Location: RVA
Posts: 9,308

Bikes: Emonda SL6

Mentioned: 97 Post(s)
Tagged: 1 Thread(s)
Quoted: 5721 Post(s)
Liked 261 Times in 99 Posts
Originally Posted by merlinextraligh
I'd resize the chain. Far better to have too much chain so it wont wrap in the small/small combination, than not enough to go in the big/big.

Someday you'll inadvertently shift into the big/big, and it can be a very expensive misshift.
I've always wondered exactly what would break if your chain is too short and you shift into big/big. Would the derailleur hanger snap? Would the chain itself break? Would the Di2 servos get damaged trying to move the chain into a gear it can't fit on? Not sure, don't really want to find out myself.
Dan333SP is offline  
Old 04-19-17, 09:41 AM
  #9  
merlinextraligh
pan y agua
 
merlinextraligh's Avatar
 
Join Date: Aug 2005
Location: Jacksonville
Posts: 31,273

Bikes: Willier Zero 7; Merlin Extralight; Calfee Dragonfly tandem, Calfee Adventure tandem; Cervelo P2; Motebecane Ti Fly 29er; Motebecanne Phantom Cross; Schwinn Paramount Track bike

Mentioned: 17 Post(s)
Tagged: 0 Thread(s)
Quoted: 1428 Post(s)
Liked 697 Times in 353 Posts
The chain jams as you force it into the too big gear. You're still pedaling, putting force to the jammed situation, until you realize what's going on. This is even worse on the tandem, where you've got double the force, and less than instant feed back to the captain. Worst case scenario, it rips the derailleur hanger from the frame ( or just bends the derailleur itself), puts the derailleur in the spokes, trashes the wheel, and you come to an unplanned screeching halt.
__________________
You could fall off a cliff and die.
You could get lost and die.
You could hit a tree and die.
OR YOU COULD STAY HOME AND FALL OFF THE COUCH AND DIE.

Last edited by merlinextraligh; 04-19-17 at 09:48 AM.
merlinextraligh is offline  
Likes For merlinextraligh:
Old 04-19-17, 11:57 AM
  #10  
Fergp
Newbie
Thread Starter
 
Join Date: May 2014
Posts: 13
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 7 Post(s)
Likes: 0
Liked 3 Times in 2 Posts
Originally Posted by merlinextraligh
I'd resize the chain. Far better to have too much chain so it wont wrap in the small/small combination, than not enough to go in the big/big.

Someday you'll inadvertently shift into the big/big, and it can be a very expensive misshift.
Yes, I understand, but when I'm in the small/small the chain is almost hitting the 2 pulleys and there is very little tension in the spring. I am afraid that adding one more link to the chain will create a problem at the other extreme.
Fergp is offline  
Old 04-19-17, 12:08 PM
  #11  
merlinextraligh
pan y agua
 
merlinextraligh's Avatar
 
Join Date: Aug 2005
Location: Jacksonville
Posts: 31,273

Bikes: Willier Zero 7; Merlin Extralight; Calfee Dragonfly tandem, Calfee Adventure tandem; Cervelo P2; Motebecane Ti Fly 29er; Motebecanne Phantom Cross; Schwinn Paramount Track bike

Mentioned: 17 Post(s)
Tagged: 0 Thread(s)
Quoted: 1428 Post(s)
Liked 697 Times in 353 Posts
The point is that it is better to have to stay out of the small/small, than the big/big

There's no reason that you need to use the smallest cogs, with the small ring. You've got comparable ratios available using the big ring and a different cog.

If you size for the big ring and you put it in the small/small combination, nothing really bad happens. It's noisy and sloppy and you realize don't use that combination.

If you size for the small/small, and inadvertently shift into the big/big under load you potentially: 1) trash a derailleur; 2) trash a chain; 3) trash the frame (by breaking the dropout/derailleur hanger); 4) trash the rear wheel, and 5) crash the bike.

Admittedly, the odds of all that happening are low, but it can and does happen. And the odds are fairly decent that eventually you'll forget, and at least f up an expensive Di2 derailleur.

If you don't have a derailleur with enough wrap capacity for the entire range, it is a dramatically better idea, when you consider the risks, to size for the big/big.
__________________
You could fall off a cliff and die.
You could get lost and die.
You could hit a tree and die.
OR YOU COULD STAY HOME AND FALL OFF THE COUCH AND DIE.
merlinextraligh is offline  
Old 05-19-17, 08:02 PM
  #12  
TigerMom
Member
 
Join Date: May 2017
Posts: 25
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 17 Post(s)
Liked 0 Times in 0 Posts
Just curious as to the approximate price that changing the Triple to Di2 cost you?

I'm hoping SRAM comes out with the 1x 12 speed system for road bikes with drop bars sooner rather than later. Then, I don't have to worry about electronic compatibility/batteries
TigerMom is offline  
Old 08-27-19, 02:29 AM
  #13  
poluf
Junior Member
 
Join Date: Aug 2019
Posts: 5
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 3 Post(s)
Likes: 0
Liked 0 Times in 0 Posts
Originally Posted by Fergp
Yes, I understand, but when I'm in the small/small the chain is almost hitting the 2 pulleys and there is very little tension in the spring. I am afraid that adding one more link to the chain will create a problem at the other extreme.
Hello
What is the front dérailleur ?
Thx ŕ lot
Stéphan
poluf is offline  
Old 08-27-19, 06:50 AM
  #14  
Trsnrtr
Super Modest
 
Trsnrtr's Avatar
 
Join Date: Jun 2002
Location: Central Illinois
Posts: 23,392

Bikes: Trek Emonda, Giant Propel, Colnago V3, Co-Motion Supremo, ICE VTX WC

Mentioned: 107 Post(s)
Tagged: 1 Thread(s)
Quoted: 10894 Post(s)
Liked 4,559 Times in 2,089 Posts
Moved to Tandem forum.
__________________
Keep the chain tight!







Trsnrtr is offline  
Old 08-27-19, 08:45 AM
  #15  
oldacura
Senior Member
 
oldacura's Avatar
 
Join Date: Nov 2006
Location: Lafayette, Colorado
Posts: 1,047

Bikes: 1998 Co-Motion Co-Pilot, 2015 Calfee Tetra

Mentioned: 1 Post(s)
Tagged: 0 Thread(s)
Quoted: 176 Post(s)
Likes: 0
Liked 6 Times in 5 Posts
Where did you get the chainring guard?
oldacura is offline  
Old 08-27-19, 09:24 AM
  #16  
ahultin
Senior Member
 
ahultin's Avatar
 
Join Date: May 2007
Location: Bonsall, Ca
Posts: 679

Bikes: 2003 Cannondale Jekyll 1000, 2014 Fuji Finest 1.5 (wife), 2008 Fuji Finest 1.0 (Daughter), 2012 Fuji Cross 2.0 (son), 2011 Cannondale Road Tandem 2

Mentioned: 7 Post(s)
Tagged: 0 Thread(s)
Quoted: 57 Post(s)
Liked 27 Times in 17 Posts
Originally Posted by oldacura
Where did you get the chainring guard?
Not sure if the OP will see this as it is from 2017 and moved from road cycling. That brand guard is readily available on Ebay and Amazon is the $30-40 range depending on size
ahultin is offline  
Old 08-28-19, 08:20 AM
  #17  
Fergp
Newbie
Thread Starter
 
Join Date: May 2014
Posts: 13
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 7 Post(s)
Likes: 0
Liked 3 Times in 2 Posts
Originally Posted by poluf
Hello
What is the front dérailleur ?
Thx ŕ lot
Stéphan
It's an Ultegra DI2 11 speed front derailleur. I did end up changing the big ring to 50 tooth (still 38 small ring), to improve shifting performance. We have done about 3000 miles since the DI2 upgrade and still love it!
Fergp is offline  
Old 08-28-19, 09:20 AM
  #18  
oldacura
Senior Member
 
oldacura's Avatar
 
Join Date: Nov 2006
Location: Lafayette, Colorado
Posts: 1,047

Bikes: 1998 Co-Motion Co-Pilot, 2015 Calfee Tetra

Mentioned: 1 Post(s)
Tagged: 0 Thread(s)
Quoted: 176 Post(s)
Likes: 0
Liked 6 Times in 5 Posts
Ours was not a conversion but a new build Calfee Di2. I wanted the widest range we could get out of a 2x system. We're at 52t x 34t up front with a 40t x 11t cassette. It was set up with a K-Edge long derailleur arm. We didn't try the Wolf Tooth Road Link. I really don't know which is better.

The bike shifts fine despite the fact that we're beyond the recommended range up front (18 tooth difference).

My biggest complaint is that the drop from the big ring to the small is huge and I need to make sure that I notify my stoker about this upcoming drop. However, we do use the full range when climbing & descending big hills.
oldacura is offline  
Old 08-28-19, 10:32 PM
  #19  
geoffs
Full Member
 
geoffs's Avatar
 
Join Date: Sep 2004
Location: Sydney
Posts: 322

Bikes: Co-Motion Mocha Co-pilot, Habanero custom commuter, Seven Axiom SL, Seven Axiom SLX, Blom Track

Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 79 Post(s)
Liked 12 Times in 10 Posts
Chinook tandems sells a longer pilley cage which would solve your chainwrap problems. We're using a Digirit pulley cage on our eTap rear derailleur but a bit longer would be good
geoffs is offline  
Old 09-19-19, 06:31 PM
  #20  
karinbur
Senior Member
 
Join Date: Jun 2005
Location: Sonoma County, California
Posts: 56

Bikes: Moots; Calfee Luna Pro; Co-motion Carerra

Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 3 Post(s)
Likes: 0
Liked 0 Times in 0 Posts
Does anyone know if the medium cage Shimano 8000 series Di2 rear derailleur can handle an 11-40 cassette? We currently have a 2016 Co-Motion Carrerra with Di2. At the time we bought it we had to get a 52-39 on the front and a K-Edge with 11-40 on the back. We'd like to change to the current Shimano 8000-series setup with 50-34 on the front if it can handle the 11-40 in the rear.
karinbur is offline  
Old 09-20-19, 12:02 AM
  #21  
ahultin
Senior Member
 
ahultin's Avatar
 
Join Date: May 2007
Location: Bonsall, Ca
Posts: 679

Bikes: 2003 Cannondale Jekyll 1000, 2014 Fuji Finest 1.5 (wife), 2008 Fuji Finest 1.0 (Daughter), 2012 Fuji Cross 2.0 (son), 2011 Cannondale Road Tandem 2

Mentioned: 7 Post(s)
Tagged: 0 Thread(s)
Quoted: 57 Post(s)
Liked 27 Times in 17 Posts
Originally Posted by karinbur
Does anyone know if the medium cage Shimano 8000 series Di2 rear derailleur can handle an 11-40 cassette? We currently have a 2016 Co-Motion Carrerra with Di2. At the time we bought it we had to get a 52-39 on the front and a K-Edge with 11-40 on the back. We'd like to change to the current Shimano 8000-series setup with 50-34 on the front if it can handle the 11-40 in the rear.
Just did a shakedown ride yesterday on a stokers new comotion steelhead running ultegra di2 Rd-r8050gs rear and slx CS-m7000 11-40 cassette. Front chainrings are the stock comotion 50/34. Shifting was flawless

Last edited by ahultin; 09-20-19 at 08:50 AM.
ahultin is offline  
Old 09-20-19, 08:29 AM
  #22  
oldacura
Senior Member
 
oldacura's Avatar
 
Join Date: Nov 2006
Location: Lafayette, Colorado
Posts: 1,047

Bikes: 1998 Co-Motion Co-Pilot, 2015 Calfee Tetra

Mentioned: 1 Post(s)
Tagged: 0 Thread(s)
Quoted: 176 Post(s)
Likes: 0
Liked 6 Times in 5 Posts
We have a 2015 Calfee with Ultegra Di2. I wanted the biggest range possible. We're running 52t x 34t up front with 11t x 40t in the rear. We have a K-Edge long cage on the rear derailleur. This is probably far outside the operating limits of Di2. However, it shifts fine. My only complaint is the jump between the big & small rings is huge. Unfortunately, this is the consequence of a big range with only 2 chainrings.
oldacura is offline  
Old 03-05-20, 01:08 PM
  #23  
SueFritz
Newbie
 
Join Date: May 2019
Posts: 1
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 0 Post(s)
Likes: 0
Liked 0 Times in 0 Posts
How did your conversion work out?

Hi,

We're looking at something similar. Did you have issues? Have you kept this configuration?
SueFritz is offline  
Old 03-09-20, 05:10 AM
  #24  
Fergp
Newbie
Thread Starter
 
Join Date: May 2014
Posts: 13
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 7 Post(s)
Likes: 0
Liked 3 Times in 2 Posts
Yes, we still love it! (had a great ride yesterday) I did change the big ring from 52 to 50. This this improved the shift up from the 38 tooth ring and helped with the chain wrap in the back in the rare times you ride the extremes (11-38 and 40-50).

Paul
Fergp is offline  
Old 07-29-21, 10:51 AM
  #25  
eischman
Member
 
Join Date: Jun 2014
Location: Raleigh Durham NC
Posts: 31

Bikes: fixie, s29er single speed, 27.5 all mnt bike, road/tr bike tandem

Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 2 Post(s)
Likes: 0
Liked 0 Times in 0 Posts
My di2 potential setup need help

I only want 1 tandem and understand it will not be able to do anything perfect. I got a custom ti frame and fork and had problems with the initial build. 1. The tandem specialist in my area said a 50/34 and a 10-42 would not work (break the rear derraileur) so the made it a 10 and had it not shift into the 42. Should it have worked? The next thing is I did not put cables stops thinking I would run full housing. Shifting is delayed on rear and problem with front derraileur. I have now decided to go di2 . I do not plan to use a front derraileur I have a 2 sets of wheels road with a 10-32 to use with 50t and a 10-42 to use with mnt /gravel to prevent from ruining the derraileur. I bought di2 Ultegra shifters and xtr rear. I was thinking about putting the battery on the underside of the stoker toptube. What do you think? Any comments? I may try a front derraileur later



Last edited by eischman; 07-29-21 at 10:54 AM.
eischman is offline  

Thread Tools
Search this Thread

Contact Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service -

Copyright © 2024 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.