Go Back  Bike Forums > Bike Forums > Bicycle Mechanics
Reload this Page >

Another 126mm to 130mm thread

Notices
Bicycle Mechanics Broken bottom bracket? Tacoed wheel? If you're having problems with your bicycle, or just need help fixing a flat, drop in here for the latest on bicycle mechanics & bicycle maintenance.

Another 126mm to 130mm thread

Old 09-24-21, 11:57 AM
  #1  
jnbrown
Senior Member
Thread Starter
 
jnbrown's Avatar
 
Join Date: Nov 2006
Location: Encinitas, CA
Posts: 1,292
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 132 Post(s)
Liked 95 Times in 52 Posts
Another 126mm to 130mm thread

I just received my 1985 Mercian frameset.
I measured the rear dropouts and they are 126mm.
I would like to use a 130mm hub. The options as I understand it are:

1. Leave as is and just spread the dropouts when putting the wheel in. I tried spreading them and it does take a little bit of effort.

2. Spread them by hand by using a threaded rod, washers and nuts. This could risk damaging the frame.

3. Take it to a frame builder and have them do it.

Option 1 is preferred and I don't plan on taking off the wheel except for flats.
I know of two frame builders locally (SoCal) but not sure if they do this and how much they charge.

Thanks for any advise.
jnbrown is offline  
Old 09-24-21, 12:21 PM
  #2  
icemilkcoffee 
Senior Member
 
icemilkcoffee's Avatar
 
Join Date: Aug 2009
Posts: 2,592
Mentioned: 13 Post(s)
Tagged: 0 Thread(s)
Quoted: 1541 Post(s)
Liked 1,702 Times in 956 Posts
Why do you want to spread it to 130mm? Just leave it at 126mm. Depending on which hub you plan to use, there are different ways to narrow the hubs to 126mm.

Speaking for myself, I will never buy a frame that has been tweaked by some rando with a 2X4 on their garage floor. Do not do this to anything other than a throw-away frame that has no value to anyone.

Last edited by icemilkcoffee; 09-24-21 at 12:36 PM.
icemilkcoffee is online now  
Old 09-24-21, 12:33 PM
  #3  
shelbyfv
Expired Member
 
shelbyfv's Avatar
 
Join Date: Jun 2007
Location: TN
Posts: 11,461
Mentioned: 37 Post(s)
Tagged: 0 Thread(s)
Quoted: 3638 Post(s)
Liked 5,316 Times in 2,701 Posts
It's easy to spread a steel frame from 126 to 130, you can do it yourself with 30 minutes of research and a 2X4. The drop outs may end up not quite parallel but this is another easy fix. Having said that, it's a complete non issue to put a 130 hub in a 126 frame, even if the frame is aluminum.
shelbyfv is offline  
Old 09-24-21, 12:56 PM
  #4  
jnbrown
Senior Member
Thread Starter
 
jnbrown's Avatar
 
Join Date: Nov 2006
Location: Encinitas, CA
Posts: 1,292
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 132 Post(s)
Liked 95 Times in 52 Posts
Originally Posted by icemilkcoffee
Why do you want to spread it to 130mm? Just leave it at 126mm. Depending on which hub you plan to use, there are different ways to narrow the hubs to 126mm.

Speaking for myself, I will never buy a frame that has been tweaked by some rando with a 2X4 on their garage floor. Do not do this to anything other than a throw-away frame that has no value to anyone.
Because I want to use an 11 speed cassette, I don't think that is possible with a hub that is 126mm.
I agree with the 2x4, I do not want to do that with a frame that I value highly.
jnbrown is offline  
Old 09-24-21, 01:08 PM
  #5  
Iride01 
I'm good to go!
 
Iride01's Avatar
 
Join Date: Jul 2017
Location: Mississippi
Posts: 14,811

Bikes: Tarmac Disc Comp Di2 - 2020

Mentioned: 50 Post(s)
Tagged: 0 Thread(s)
Quoted: 6100 Post(s)
Liked 4,732 Times in 3,262 Posts
I wouldn't hesitate to spread them if there isn't enough natural spring in them just to allow you to get your new 11 speed hub up in there. And if I messed it up trying to spread them, then I'd just find another frame. Old frames are plentiful IMO. Hopefully one with the proper spacing. But if not I'd try again and maybe I'll have learned some nuances about spreading the stays that I didn't realize before.

Sheldon Brown had a decent article about spreading them.

https://www.sheldonbrown.com/frame-spacing.html
Iride01 is offline  
Old 09-24-21, 01:09 PM
  #6  
L134 
Senior Member
 
Join Date: Dec 2015
Location: San Diego
Posts: 704

Bikes: 1978 Bruce Gordon, 1977 Lippy, 199? Lippy tandem, Bike Friday NWT, 1982 Trek 720, 2012 Rivendell Atlantis, 1983 Bianchi Specialissima?

Mentioned: 11 Post(s)
Tagged: 0 Thread(s)
Quoted: 345 Post(s)
Liked 170 Times in 105 Posts
Originally Posted by jnbrown
I just received my 1985 Mercian frameset.
I measured the rear dropouts and they are 126mm.
I would like to use a 130mm hub. The options as I understand it are:

1. Leave as is and just spread the dropouts when putting the wheel in. I tried spreading them and it does take a little bit of effort.

2. Spread them by hand by using a threaded rod, washers and nuts. This could risk damaging the frame.

3. Take it to a frame builder and have them do it.

Option 1 is preferred and I don't plan on taking off the wheel except for flats.
I know of two frame builders locally (SoCal) but not sure if they do this and how much they charge.

Thanks for any advise.
I've had it done thru Joe Bell in Spring Valley. Take bare frame and fork in and get frame spread and everything aligned professionally for $100.
L134 is offline  
Likes For L134:
Old 09-24-21, 01:14 PM
  #7  
jnbrown
Senior Member
Thread Starter
 
jnbrown's Avatar
 
Join Date: Nov 2006
Location: Encinitas, CA
Posts: 1,292
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 132 Post(s)
Liked 95 Times in 52 Posts
Originally Posted by L134
I've had it done thru Joe Bell in Spring Valley. Take bare frame and fork in and get frame spread and everything aligned professionally for $100.
Forgot about Joe Bell, good suggestion.
jnbrown is offline  
Old 09-24-21, 01:36 PM
  #8  
70sSanO
Senior Member
 
70sSanO's Avatar
 
Join Date: Feb 2015
Location: Mission Viejo
Posts: 5,772

Bikes: 1986 Cannondale SR400 (Flat bar commuter), 1988 Cannondale Criterium XTR, 1992 Serotta T-Max, 1995 Trek 970

Mentioned: 20 Post(s)
Tagged: 0 Thread(s)
Quoted: 1935 Post(s)
Liked 2,150 Times in 1,313 Posts
A lot of people have gone from 126mm to 130mm without any issues.

I’ve used the threaded rod with nuts and washers and the followed up with a crescent wrench to get the dropouts parallel. Doesn’t seem to be an issue with 8 or 9 speed.

However, if I were going to 11 speed, I’d probably take the frame in to a “competent” shop/builder to make sure it was done right and aligned correctly.

John
70sSanO is offline  
Old 09-24-21, 01:36 PM
  #9  
shelbyfv
Expired Member
 
shelbyfv's Avatar
 
Join Date: Jun 2007
Location: TN
Posts: 11,461
Mentioned: 37 Post(s)
Tagged: 0 Thread(s)
Quoted: 3638 Post(s)
Liked 5,316 Times in 2,701 Posts
Originally Posted by Iride01
Sheldon Brown had a decent article about spreading them.

https://www.sheldonbrown.com/frame-spacing.html
That can't be legit. Obviously some rando with a 2X4
shelbyfv is offline  
Likes For shelbyfv:
Old 09-24-21, 01:57 PM
  #10  
Bill Kapaun
Really Old Senior Member
 
Bill Kapaun's Avatar
 
Join Date: Feb 2007
Location: Mid Willamette Valley, Orygun
Posts: 13,824

Bikes: 87 RockHopper,2008 Specialized Globe. Both upgraded to 9 speeds.

Mentioned: 20 Post(s)
Tagged: 0 Thread(s)
Quoted: 1774 Post(s)
Liked 1,231 Times in 852 Posts
Originally Posted by jnbrown
Forgot about Joe Bell, good suggestion.
If you are going to pay a competent mechanic, you might shoot for >130mm since you are going 11 speed.
Wider reduces wheel dish. (I'm pushing about 132 on a former 126)
A rear offset spoked rim would greatly help too.
Bill Kapaun is offline  
Likes For Bill Kapaun:
Old 09-24-21, 02:14 PM
  #11  
phtomita
Senior Member
 
Join Date: Jan 2018
Location: Redmond, WA
Posts: 836

Bikes: '86 Nishiki Tri-A, '84 Centurion PT15, '03 Litespeed Firenze

Mentioned: 10 Post(s)
Tagged: 0 Thread(s)
Quoted: 242 Post(s)
Liked 176 Times in 110 Posts
This worked great for me.

phtomita is offline  
Likes For phtomita:
Old 09-24-21, 02:17 PM
  #12  
squirtdad
Senior Member
 
squirtdad's Avatar
 
Join Date: Jul 2006
Location: San Jose (Willow Glen) Ca
Posts: 9,856

Bikes: Kirk Custom JK Special, '84 Team Miyata,(dura ace old school) 80?? SR Semi-Pro 600 Arabesque

Mentioned: 104 Post(s)
Tagged: 0 Thread(s)
Quoted: 2304 Post(s)
Liked 2,741 Times in 1,499 Posts
Originally Posted by jnbrown
I just received my 1985 Mercian frameset.
I measured the rear dropouts and they are 126mm.
I would like to use a 130mm hub. The options as I understand it are:

1. Leave as is and just spread the dropouts when putting the wheel in. I tried spreading them and it does take a little bit of effort.

2. Spread them by hand by using a threaded rod, washers and nuts. This could risk damaging the frame.

3. Take it to a frame builder and have them do it.

Option 1 is preferred and I don't plan on taking off the wheel except for flats.
I know of two frame builders locally (SoCal) but not sure if they do this and how much they charge.

Thanks for any advise.
I am not a fan of the threaded rod method.... I used a 2x4 and sheldon's method to go from 126 to 135 https://www.sheldonbrown.com/frame-spacing.html

also some old school bikes shops will do this.
__________________
Life is too short not to ride the best bike you have, as much as you can
(looking for Torpado Super light frame/fork or for Raleigh International frame fork 58cm)



squirtdad is offline  
Old 09-24-21, 02:40 PM
  #13  
icemilkcoffee 
Senior Member
 
icemilkcoffee's Avatar
 
Join Date: Aug 2009
Posts: 2,592
Mentioned: 13 Post(s)
Tagged: 0 Thread(s)
Quoted: 1541 Post(s)
Liked 1,702 Times in 956 Posts
Originally Posted by jnbrown
Because I want to use an 11 speed cassette, I don't think that is possible with a hub that is 126mm.
If you must have an 11 speed drivetrain then I guess you have no choice. Do you really need an 11 speed drivetrain that 7,8,9 speeds won't do?
icemilkcoffee is online now  
Old 09-24-21, 03:15 PM
  #14  
shelbyfv
Expired Member
 
shelbyfv's Avatar
 
Join Date: Jun 2007
Location: TN
Posts: 11,461
Mentioned: 37 Post(s)
Tagged: 0 Thread(s)
Quoted: 3638 Post(s)
Liked 5,316 Times in 2,701 Posts
I've been a fan of 9 speed and would have been perfectly happy if they'd focused just on improving that. However, when it's gone it's gone. If you want to buy a new group you are stuck with 11 speed unless you want to venture far down the food chain.
shelbyfv is offline  
Old 09-24-21, 03:33 PM
  #15  
delbiker1 
Mother Nature's Son
 
delbiker1's Avatar
 
Join Date: Mar 2016
Location: Sussex County, Delaware
Posts: 3,111

Bikes: 2014 Orbea Avant MD30, 2004 Airborne Zeppelin TI, 2003 Lemond Poprad, 2001 Lemond Tourmalet, 2014? Soma Smoothie

Mentioned: 14 Post(s)
Tagged: 0 Thread(s)
Quoted: 838 Post(s)
Liked 1,414 Times in 801 Posts
Originally Posted by phtomita

Same for me. A few bucks and it was really easy. The drop outs needed minor adjusting, I used RJ's method for that. I cannot say what anyone else's outcome might be, but I would not not hesitate to do it again. Everything came straight and aligned, no issues.
delbiker1 is offline  
Old 09-24-21, 03:48 PM
  #16  
philbob57
Senior Member
 
Join Date: Jul 2013
Location: Chicago North Shore
Posts: 2,331

Bikes: frankenbike based on MKM frame

Mentioned: 7 Post(s)
Tagged: 0 Thread(s)
Quoted: 714 Post(s)
Liked 602 Times in 371 Posts
A former frame builder cold set my 121 mm dropouts to 128 mm. I gave him my bare frame with BB and $75 and got my frame back with overhauled BB in addition to the new spacing. It would have been $50 if I had removed the BB. That was 5 years ago, so $100 for a full alignment ...um... doesn't seem out of line for 2021 in SoCal. $100 may even be a bargain.
philbob57 is offline  
Old 09-24-21, 04:27 PM
  #17  
jnbrown
Senior Member
Thread Starter
 
jnbrown's Avatar
 
Join Date: Nov 2006
Location: Encinitas, CA
Posts: 1,292
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 132 Post(s)
Liked 95 Times in 52 Posts
Originally Posted by icemilkcoffee
If you must have an 11 speed drivetrain then I guess you have no choice. Do you really need an 11 speed drivetrain that 7,8,9 speeds won't do?
I guess I am spoiled with 11 speed although now there is 12 speed.
It is not easy to find components for 7,8,9 speed but I admit that I have not looked hard.
Also it would be nice if it was compatible with my other bike in case I needed to swap wheels or components.
jnbrown is offline  
Old 09-24-21, 04:46 PM
  #18  
ThermionicScott 
working on my sandal tan
 
ThermionicScott's Avatar
 
Join Date: Aug 2011
Location: CID
Posts: 22,625

Bikes: 1991 Bianchi Eros, 1964 Armstrong, 1988 Diamondback Ascent, 1988 Bianchi Premio, 1987 Bianchi Sport SX, 1980s Raleigh mixte (hers), All-City Space Horse (hers)

Mentioned: 98 Post(s)
Tagged: 0 Thread(s)
Quoted: 3868 Post(s)
Liked 2,560 Times in 1,574 Posts
Originally Posted by shelbyfv
That can't be legit. Obviously some rando with a 2X4
Obviously, he only dealt in "throw-away frames that have no value to anyone."
__________________
Originally Posted by chandltp
There's no such thing as too far.. just lack of time
Originally Posted by noglider
People in this forum are not typical.
RUSA #7498
ThermionicScott is offline  
Likes For ThermionicScott:
Old 09-24-21, 05:46 PM
  #19  
squirtdad
Senior Member
 
squirtdad's Avatar
 
Join Date: Jul 2006
Location: San Jose (Willow Glen) Ca
Posts: 9,856

Bikes: Kirk Custom JK Special, '84 Team Miyata,(dura ace old school) 80?? SR Semi-Pro 600 Arabesque

Mentioned: 104 Post(s)
Tagged: 0 Thread(s)
Quoted: 2304 Post(s)
Liked 2,741 Times in 1,499 Posts
Originally Posted by icemilkcoffee
If you must have an 11 speed drivetrain then I guess you have no choice. Do you really need an 11 speed drivetrain that 7,8,9 speeds won't do?
need 130 for anything more than 7 speed
__________________
Life is too short not to ride the best bike you have, as much as you can
(looking for Torpado Super light frame/fork or for Raleigh International frame fork 58cm)



squirtdad is offline  
Old 09-24-21, 06:15 PM
  #20  
zacster
Senior Member
 
Join Date: Jul 2004
Location: Brooklyn NY
Posts: 7,702

Bikes: Kuota Kredo/Chorus, Trek 7000 commuter, Trek 8000 MTB and a few others

Mentioned: 1 Post(s)
Tagged: 0 Thread(s)
Quoted: 22 Post(s)
Liked 456 Times in 358 Posts
I stuck a 130 wheel in my 126 Davidson with no issues at all, and this was over 15 years ago. It is still around and kicking and has returned home to Seattle where I intend to ride it when I visit my son out there. It'll be a real kick to ride a 40 year old bike there! I'll make it a point to visit Davidson's shop.
zacster is offline  
Old 09-25-21, 01:59 AM
  #21  
Lazyass
Senior Member
 
Join Date: Jul 2008
Location: Minas Ithil
Posts: 9,337
Mentioned: 66 Post(s)
Tagged: 0 Thread(s)
Quoted: 2432 Post(s)
Liked 638 Times in 395 Posts
I've ran a 130 hub in a 126 frame for years and it takes almost no effort to remove the wheel. Just slide the axle in all the way the right dropout and you only have to slightly pull on the left side to get it in. I also have another vintage frame that was cold set to 130 before I bought and it's nice but not worth the effort IMO. Plus someday you might want to run a vintage group/hubs or someone else might if you sell it.
Lazyass is offline  
Old 09-25-21, 08:58 AM
  #22  
zacster
Senior Member
 
Join Date: Jul 2004
Location: Brooklyn NY
Posts: 7,702

Bikes: Kuota Kredo/Chorus, Trek 7000 commuter, Trek 8000 MTB and a few others

Mentioned: 1 Post(s)
Tagged: 0 Thread(s)
Quoted: 22 Post(s)
Liked 456 Times in 358 Posts
Originally Posted by Lazyass
I've ran a 130 hub in a 126 frame for years and it takes almost no effort to remove the wheel. Just slide the axle in all the way the right dropout and you only have to slightly pull on the left side to get it in. I also have another vintage frame that was cold set to 130 before I bought and it's nice but not worth the effort IMO. Plus someday you might want to run a vintage group/hubs or someone else might if you sell it.
Yes, those of us that have done this all know it just works. I never understand the reluctance or the need to set the frame. I also have a Cannondale frame that has a 126 setup on it, but the frame itself is 128 and can take 130 as well and those bikes were sold both ways.

Last edited by zacster; 09-25-21 at 11:16 AM.
zacster is offline  
Old 09-25-21, 10:30 AM
  #23  
icemilkcoffee 
Senior Member
 
icemilkcoffee's Avatar
 
Join Date: Aug 2009
Posts: 2,592
Mentioned: 13 Post(s)
Tagged: 0 Thread(s)
Quoted: 1541 Post(s)
Liked 1,702 Times in 956 Posts
Originally Posted by squirtdad
need 130 for anything more than 7 speed
8 of 9 on 7, etc. Just last week somebody reported that a CS 6700 10 speed cassette that has the dished in back side, fits on the 7 sp hub just fine. Or alternatively just take the spacer off the left side and run an Off center rim to compensate.
icemilkcoffee is online now  
Old 09-25-21, 11:35 AM
  #24  
KCT1986
Senior Member
 
Join Date: Jan 2016
Posts: 818
Mentioned: 1 Post(s)
Tagged: 0 Thread(s)
Quoted: 333 Post(s)
Liked 294 Times in 221 Posts
Originally Posted by squirtdad
need 130 for anything more than 7 speed
Absolutely not true, there are many ways to run more than 7 speed on frames with OLD less than 130mm. Threads on this site have detailed this numerous times. Just need to have the knowledge on wheel structure and mechanical ability to do this properly.
KCT1986 is offline  
Old 09-25-21, 12:06 PM
  #25  
squirtdad
Senior Member
 
squirtdad's Avatar
 
Join Date: Jul 2006
Location: San Jose (Willow Glen) Ca
Posts: 9,856

Bikes: Kirk Custom JK Special, '84 Team Miyata,(dura ace old school) 80?? SR Semi-Pro 600 Arabesque

Mentioned: 104 Post(s)
Tagged: 0 Thread(s)
Quoted: 2304 Post(s)
Liked 2,741 Times in 1,499 Posts
Originally Posted by squirtdad
need 130 for anything more than 7 speed
Originally Posted by icemilkcoffee
8 of 9 on 7, etc. Just last week somebody reported that a CS 6700 10 speed cassette that has the dished in back side, fits on the 7 sp hub just fine. Or alternatively just take the spacer off the left side and run an Off center rim to compensate.
Originally Posted by KCT1986
Absolutely not true, there are many ways to run more than 7 speed on frames with OLD less than 130mm. Threads on this site have detailed this numerous times. Just need to have the knowledge on wheel structure and mechanical ability to do this properly.
let me rephrase: Need 130 to do more than 7 speed, without having to do a lot of fussy hacking or messing around, like re-dishing. YMMV but IME trying to make things work beyond what they were designed to do often results in inferior results.
__________________
Life is too short not to ride the best bike you have, as much as you can
(looking for Torpado Super light frame/fork or for Raleigh International frame fork 58cm)



squirtdad is offline  

Thread Tools
Search this Thread

Contact Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service -

Copyright © 2024 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.