Go Back  Bike Forums > Bike Forums > Fifty Plus (50+)
Reload this Page >

The Dominance of Ultra-Low Gear Racing Drive-trains

Notices
Fifty Plus (50+) Share the victories, challenges, successes and special concerns of bicyclists 50 and older. Especially useful for those entering or reentering bicycling.

The Dominance of Ultra-Low Gear Racing Drive-trains

Old 08-19-22, 09:20 AM
  #1  
Classtime 
Senior Member
Thread Starter
 
Classtime's Avatar
 
Join Date: Jan 2015
Location: Los Angeles
Posts: 4,672

Bikes: 82 Medici, 2011 Richard Sachs, 2011 Milwaukee Road

Mentioned: 54 Post(s)
Tagged: 0 Thread(s)
Quoted: 1924 Post(s)
Liked 1,954 Times in 1,086 Posts
The Dominance of Ultra-Low Gear Racing Drive-trains

Saturday, I started with the local training ride which is attended by many accomplished and current 50 and 60+ National Champions. Of course, most have new bikes with electronic shifting and disk brakes. But what struck me was that most of these guys and gals had huge cogsets. Many of them went to 34! Now compact cranksets have been popular for some time but 34 tooth cogs on a road racing bike? Makes me think of doing that to my modern bike.
__________________
I don't do: disks, tubeless, e-shifting, or bead head nymphs.
Classtime is offline  
Likes For Classtime:
Old 08-19-22, 10:47 AM
  #2  
Barrettscv 
Have bike, will travel
 
Barrettscv's Avatar
 
Join Date: Feb 2006
Location: Lake Geneva, WI
Posts: 12,392

Bikes: Ridley Helium SLX, Canyon Endurance SL, De Rosa Professional, Eddy Merckx Corsa Extra, Schwinn Paramount (1 painted, 1 chrome), Peugeot PX10, Serotta Nova X, Simoncini Cyclocross Special, Raleigh Roker, Pedal Force CG2 and CX2

Mentioned: 46 Post(s)
Tagged: 0 Thread(s)
Quoted: 910 Post(s)
Liked 288 Times in 158 Posts
Originally Posted by Classtime
Saturday, I started with the local training ride which is attended by many accomplished and current 50 and 60+ National Champions. Of course, most have new bikes with electronic shifting and disk brakes. But what struck me was that most of these guys and gals had huge cogsets. Many of them went to 34! Now compact cranksets have been popular for some time but 34 tooth cogs on a road racing bike? Makes me think of doing that to my modern bike.
I'm using a 50&34 crank with an 11-32 cassette on my lightweight road bike and this provides me the ability to climb at 5 mph with a 50 rpm cadence. On pavement, that's as big a cassette I need.

On my gravel bike I have a 46&33 cyclocross crankset with an 11-36 eleven speed cassette. I can climb a 20% grade on gravel and stay seated with a 40 rpm cadence.
__________________
When I ride my bike I feel free and happy and strong. I'm liberated from the usual nonsense of day to day life. Solid, dependable, silent, my bike is my horse, my fighter jet, my island, my friend. Together we will conquer that hill and thereafter the world.

Last edited by Barrettscv; 08-19-22 at 03:11 PM.
Barrettscv is offline  
Old 08-19-22, 11:01 AM
  #3  
scottfsmith
I like bike
 
scottfsmith's Avatar
 
Join Date: Feb 2021
Location: Merry Land USA
Posts: 662

Bikes: Roubaix Comp 2020

Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 267 Post(s)
Liked 283 Times in 191 Posts
My cassette goes to 34 and I love it, also I have 50-34 in front. I only need to stand when the grade is 20+% which is almost never. Similarly the 50 in front is occasionally too small, but so what I'll just do 120rpm for a minute no biggie.
scottfsmith is offline  
Likes For scottfsmith:
Old 08-19-22, 11:10 AM
  #4  
t2p
Senior Member
 
Join Date: May 2022
Location: USA - Southwest PA
Posts: 2,980

Bikes: Cannondale - Gary Fisher - Giant - Litespeed - Schwinn Paramount - Schwinn (lugged steel) - Trek OCLV

Mentioned: 6 Post(s)
Tagged: 0 Thread(s)
Quoted: 1359 Post(s)
Liked 1,803 Times in 1,038 Posts
inadequate gearing on road bikes - and poor rider position/fit - was a contributing factor to the growth of the 'mountain bike' in the 90's

most of the 'mountain bikes' never saw off road use

then many realized the heavy fat tire bikes were not ideal for road riding - and the pendulum swung back toward the road bike and the eventual move to the 'gravel bike' (with improved gearing and rider position etc)

this is of course an oversimplification - but summarized the movement
t2p is offline  
Old 08-19-22, 12:08 PM
  #5  
I-Like-To-Bike
Been Around Awhile
 
I-Like-To-Bike's Avatar
 
Join Date: Oct 2004
Location: Burlington Iowa
Posts: 29,951

Bikes: Vaterland and Ragazzi

Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 12 Post(s)
Liked 1,517 Times in 1,031 Posts
Originally Posted by t2p
inadequate gearing on road bikes - and poor rider position/fit - was a contributing factor to the growth of the 'mountain bike' in the 90's
As well as a contributing factor, in combination with uncomfortable OEM rock hard ass -hatchet saddles and narrow high pressure tires, to stunting, if not killing the so-called "bike boom" of the early 70's. The relative comfort of the 80's mountain bike for casual recreational riding regardless of road surface, as well as typical commuting or local transportation purposes, in comparison to the so-called "10 speed racers" was obvious to all but speed obsessed "enthusiasts."
I-Like-To-Bike is offline  
Likes For I-Like-To-Bike:
Old 08-19-22, 01:14 PM
  #6  
Polaris OBark
ignominious poltroon
 
Polaris OBark's Avatar
 
Join Date: Jan 2022
Posts: 3,927
Mentioned: 3 Post(s)
Tagged: 0 Thread(s)
Quoted: 2185 Post(s)
Liked 3,337 Times in 1,742 Posts
I put an 11-36T cassette on a few different wheel-sets, because the 11-34T was insufficiently low when paired with a 46/30 T crankset.

The latest example was with a 2X GRX derailleur for my wife. It was clear that there would be plenty of room to go lower, perhaps to 40 or 42T.

It is good to have options, especially around steep (> 20%) grades, and as age takes its toll.
Polaris OBark is offline  
Old 08-19-22, 01:29 PM
  #7  
79pmooney
Senior Member
 
79pmooney's Avatar
 
Join Date: Oct 2014
Location: Portland, OR
Posts: 12,830

Bikes: (2) ti TiCycles, 2007 w/ triple and 2011 fixed, 1979 Peter Mooney, ~1983 Trek 420 now fixed and ~1973 Raleigh Carlton Competition gravel grinder

Mentioned: 128 Post(s)
Tagged: 0 Thread(s)
Quoted: 4743 Post(s)
Liked 3,860 Times in 2,509 Posts
Yeah, even this born mountain goat is moving down in gear ratios as he ages. Still haven't gone compact double and super big cassette because I like triples too much but they all have 30 and smaller chainrings. (The 30 because it's a Campy Chorus on a race bike. Sweet crankset but I think 30 is as low as it gets,) Other bikes used to be 28s and are now 24s. With 28 cassettes and FWs, decently low.
79pmooney is offline  
Old 08-19-22, 01:46 PM
  #8  
VegasTriker
Senior Member
 
Join Date: Feb 2006
Location: Sin City, Nevada
Posts: 2,879

Bikes: Catrike 700, Greenspeed GTO trike, , Linear LWB recumbent, Haluzak Horizon SWB recumbent, Balance 450 MTB, Cannondale SM800 Beast of the East

Mentioned: 19 Post(s)
Tagged: 0 Thread(s)
Quoted: 521 Post(s)
Likes: 0
Liked 227 Times in 179 Posts
I bought a top-of-the-line production road bike, Motobecane Le Champion, in the early 1970s. It was a great bike at the time for me but as I got older it became less useful. Just too darn hard on the body. I tried mountain bikes (several and still own two) but even that wasn't enough to make riding any distance really comfortable. None of these had as wide a gear range as what I ride now. Drive components have come a long way if you chose wisely. BTW, the Motobecane went to a local charity that gave it to someone who needed transportation. It was back in the charity in short order as the first recipient couldn't stand the harsh ride either. I'm sure whatever he got on the second try didn't weigh 21 pounds.
VegasTriker is offline  
Old 08-19-22, 03:24 PM
  #9  
Ogsarg
Senior Member
 
Join Date: Feb 2017
Location: Hollister, CA (not the surf town)
Posts: 1,724

Bikes: 2019 Specialized Roubaix Comp Di2, 2009 Roubaix, early 90's Giant Iguana

Mentioned: 8 Post(s)
Tagged: 0 Thread(s)
Quoted: 636 Post(s)
Liked 1,489 Times in 543 Posts
I have an 11-34 with a compact double and use the 34-34 combo more often than I thought I would. I'd probably use a 36 if I had one. I can't imagine climbing some of the hills around here with the typical road bike gearing available 20 years ago.
Ogsarg is offline  
Old 08-19-22, 04:48 PM
  #10  
road292
Newbie
 
Join Date: Nov 2010
Posts: 41
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 31 Post(s)
Likes: 0
Liked 13 Times in 9 Posts
The older tight-ratio freewheels probably had 6, maybe 7 gears. Nowadays, with 10+ gears, a wider ratio doesn't typically translate into huge jumps from cog to cog. Also, mashing has gone out of style. Look at pro races from the 70s -- those guys were mashing up hills regularly. Now, pros spin up hills except for the truly steep ones (like the 20% grades on some Giro climbs or something like that).
road292 is offline  
Likes For road292:
Old 08-20-22, 09:30 AM
  #11  
Carbonfiberboy 
just another gosling
 
Carbonfiberboy's Avatar
 
Join Date: Feb 2007
Location: Everett, WA
Posts: 19,501

Bikes: CoMo Speedster 2003, Trek 5200, CAAD 9, Fred 2004

Mentioned: 115 Post(s)
Tagged: 0 Thread(s)
Quoted: 3872 Post(s)
Liked 1,920 Times in 1,369 Posts
In my 50s, I could climb everything with a 30 X 25
then I went to a 30 X 27
then to a 26 X 25
then to a 26 X 27
then to a 26 X 30, where I seem to have stabilized. My normal climbing cadence is 78-83. All of this gearing on my 5200 of course.

Most of these modern gearing choices above are because the tech allows. I don't think anyone loved mashing, but that's what the tech demanded.
__________________
Results matter
Carbonfiberboy is offline  
Likes For Carbonfiberboy:
Old 08-20-22, 09:56 AM
  #12  
Wildwood 
Veteran, Pacifist
 
Wildwood's Avatar
 
Join Date: Dec 2004
Location: Seattle area
Posts: 13,303

Bikes: Bikes??? Thought this was social media?!?

Mentioned: 284 Post(s)
Tagged: 0 Thread(s)
Quoted: 3876 Post(s)
Liked 4,780 Times in 2,205 Posts
If you want to get new buyers into the bicycle buying cycle = make it simple to ride the terrain. That means lower gears. Hills are hard.

For older experienced riders - lower gears (and clutched rd's) let us remember the legs we used to have on hard terrain when derailleurs would only handle a 14/26 cogset.


I have a 13/30 freewheel coming for a bike, largest cogset i will have ever ridden on a roadie.

edit: But I have a gravel bike with 46/30 chainrings. Sometimes I like to ride slowly.
__________________
Vintage, modern, e-road. It is a big cycling universe.

Last edited by Wildwood; 08-20-22 at 10:00 AM.
Wildwood is online now  
Likes For Wildwood:
Old 08-20-22, 10:12 AM
  #13  
terrymorse 
climber has-been
 
terrymorse's Avatar
 
Join Date: Dec 2004
Location: Palo Alto, CA
Posts: 7,007

Bikes: Scott Addict R1, Felt Z1

Mentioned: 10 Post(s)
Tagged: 0 Thread(s)
Quoted: 3340 Post(s)
Liked 3,437 Times in 1,738 Posts
To see the progression of road bike "race" gearing, just look at the changes to Dura-Ace.

Several years ago, Dura-Ace was 10 speed, top-end bikes with Dura-Ace were shipped with 52-39 chainrings and 11-25 cassettes. Low gear ratio: 1.56.

The lowest 10 speed Dura-Ace was 50-34 chainrings and 11-28 cassette. Low gear ratio: 1.21.

Today, Dura-Ace is 12 speed, the standard is 52-36 and 11-30. Low gear ratio: 1.2.

The lowest 12 speed Dura-Ace available is 50-34 and 11-34. Low gear ratio: 1.0.
__________________
Ride, Rest, Repeat. ROUVY: terrymorse


terrymorse is offline  
Likes For terrymorse:
Old 08-21-22, 08:40 AM
  #14  
Hermes
Version 7.0
 
Hermes's Avatar
 
Join Date: Oct 2006
Location: SoCal
Posts: 13,099

Bikes: Too Many

Mentioned: 297 Post(s)
Tagged: 0 Thread(s)
Quoted: 1327 Post(s)
Liked 2,438 Times in 1,425 Posts
I change gearing / bikes depending on the terrain and facts and circumstances surrounding my planned or impromptu riding. I will continue to do this even as industry evolves and improves brakes and drive trains.

I use my Cervelo R5 with a 50/34 and 11/32 cassette for general purpose riding and training. I have 11 speed SRAM red electronic shifting and the combination is pretty sweet for most riding. There is a couple of shift points where I seem to be constantly shifting to find the right cadence. But that seems like a small compromise. I took this bike and gearing setup on a 42 day cycling tour of Croatia, Italy and Greece and the combination worked great for long climbs and punchy coast riding as well as longer flatter rides with the wind at my back.

If I am doing a hill climb race or just climbing, I may switch cassettes to get a particular rear cog that suits my fancy that is not on the 11/32.

My newer gravel / road bike with disc brakes is 1/11 48 chain ring with an 11/40. I changed the factory setup from a 46 to a 48 Chain ring for a higher top end and put on the smallest rear cassette that would work with the mountain derailleur. What is missing is a 12t cog in the rear cassette for road riding. Shifting is DuraAce electronic.

My time trial bike is set up with 54/39 and sometime 54/44 with an 11/23 rear cassette 10 speed manual DA. In general, the stock setup is good for flat to rolling time trials and training and the 39/23 low enough for shorter power climbs along the coast.

What I see in time trials and on the road is reconfigured gearing and the use of 1x with wide range cassettes. And I could use a bigger front chain ring for some time trial courses that feature faster downhill sections with slight downhill.

At the track, the trend for fixed gear is bigger gears and slower cadence. Yesterday, I was riding the track in a 52/13 approximately 106 gear inches. Everyone seems to be spinning slower and gearing bigger.

Personally, I like simplicity and dependable shifting when riding assuming I can get the cadence I want for the terrain. Electronic shifting plus wide range derailleurs seem to work. I like the 1x setup of my gravel bike but miss the 12t. I do not miss the triples. When they worked, they were amazing and when they went out of adjustment and failed to shift properly, I hated them. I still have one on my tandem and would like to change to electronic shifting with a double and wide range rear cassette.
Hermes is online now  
Likes For Hermes:
Old 08-21-22, 08:47 AM
  #15  
t2p
Senior Member
 
Join Date: May 2022
Location: USA - Southwest PA
Posts: 2,980

Bikes: Cannondale - Gary Fisher - Giant - Litespeed - Schwinn Paramount - Schwinn (lugged steel) - Trek OCLV

Mentioned: 6 Post(s)
Tagged: 0 Thread(s)
Quoted: 1359 Post(s)
Liked 1,803 Times in 1,038 Posts
Originally Posted by terrymorse
To see the progression of road bike "race" gearing, just look at the changes to Dura-Ace.

Several years ago, Dura-Ace was 10 speed, top-end bikes with Dura-Ace were shipped with 52-39 chainrings and 11-25 cassettes. Low gear ratio: 1.56.

The lowest 10 speed Dura-Ace was 50-34 chainrings and 11-28 cassette. Low gear ratio: 1.21.

Today, Dura-Ace is 12 speed, the standard is 52-36 and 11-30. Low gear ratio: 1.2.

The lowest 12 speed Dura-Ace available is 50-34 and 11-34. Low gear ratio: 1.0.

and traveling backward - 12-23 cogset was common before 12-25

unfortunate it took too long

but in flat areas it was probably less of an issue (if no issue)
t2p is offline  
Likes For t2p:
Old 08-22-22, 05:14 PM
  #16  
Rotten
Senior Member
 
Rotten's Avatar
 
Join Date: Mar 2015
Location: Texas panhandle
Posts: 524

Bikes: 1987 Schwinn Circuit, 1986 Schwinn Passage, 1987 Shogun Katana, 2018 Giant Anyroad Advanced, 2013 Karate Monkey

Mentioned: 15 Post(s)
Tagged: 0 Thread(s)
Quoted: 125 Post(s)
Liked 269 Times in 93 Posts
50/34 with an 11 speed 11-34 for me. Tight spacing on the high end for getting a comfortable cadence on the flats and the 34-34 combo for the occasional short steep climbs. I have had to use the 34-34 combo once to grind my way home on the flat when a storm cell popped up behind me on the way out, it was not a fun grind home.
Rotten is offline  
Old 08-23-22, 06:39 AM
  #17  
Bob Ross
your god hates me
 
Bob Ross's Avatar
 
Join Date: Apr 2006
Posts: 4,580

Bikes: 2016 Richard Sachs, 2010 Carl Strong, 2006 Cannondale Synapse

Mentioned: 10 Post(s)
Tagged: 0 Thread(s)
Quoted: 1233 Post(s)
Liked 1,241 Times in 689 Posts
Originally Posted by Classtime
most of these guys and gals had huge cogsets. Many of them went to 34! Now compact cranksets have been popular for some time but 34 tooth cogs on a road racing bike?
[edit: Derp, I misread that post, thought it was about chainrings not cogs. Never mind...]

Last edited by Bob Ross; 08-24-22 at 08:03 AM. Reason: brain-fart
Bob Ross is offline  
Old 08-23-22, 06:56 AM
  #18  
GhostRider62
Senior Member
 
Join Date: Apr 2021
Posts: 4,083
Mentioned: 6 Post(s)
Tagged: 0 Thread(s)
Quoted: 2332 Post(s)
Liked 2,094 Times in 1,311 Posts
I use a 53/39 and 11-32 sram 11 speed cassette on a couple of road bikes. I use 50/34 and 11-32 on my gravel/touring bike. Most of myroad riding uses a 1X setup AXS with 48T and 11-34 12 speed cassette although I do mount an 11-39 for hilly conditions....not ideal but not bad either. Currently trying to figure out a new bike or finding one available. I am probably going with 48/35 and 10-33 if SRAM and 52/36 and 11-34 if Shimano. Both would be fine for me as most of my hills are 9-11% with a few in the 13-16% range

It really comes down to preferred cadence and W/Kg you are willing or able to put out.
GhostRider62 is offline  
Old 08-23-22, 09:23 AM
  #19  
redcon1
Senior Member
 
redcon1's Avatar
 
Join Date: Aug 2008
Location: South Central PA
Posts: 549

Bikes: Focus Arriba, Specialized Roubaix Expert, Bianchi Impulso Allroad

Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 109 Post(s)
Liked 82 Times in 53 Posts
I just watched a stage of the TdF and saw some riders on 34/32 and a few on 34/34 for the hilly stage I attended in Mende. Modern compacts are in the Pro Peloton for most hilly stages and all mountain stages.
redcon1 is offline  
Old 08-25-22, 06:33 PM
  #20  
John E
feros ferio
 
John E's Avatar
 
Join Date: Jul 2000
Location: www.ci.encinitas.ca.us
Posts: 21,765

Bikes: 1959 Capo Modell Campagnolo; 1960 Capo Sieger (2); 1962 Carlton Franco Suisse; 1970 Peugeot UO-8; 1982 Bianchi Campione d'Italia; 1988 Schwinn Project KOM-10;

Mentioned: 44 Post(s)
Tagged: 0 Thread(s)
Quoted: 1384 Post(s)
Liked 1,294 Times in 819 Posts
Originally Posted by redcon1
I just watched a stage of the TdF and saw some riders on 34/32 and a few on 34/34 for the hilly stage I attended in Mende. Modern compacts are in the Pro Peloton for most hilly stages and all mountain stages.
That is quite the change from early 1970s stock Peugeot PA/PR/PX-10 gearing of 52-45/14-15-17-19-21

I have ridden 50-42 / 14-16-18-20-23-26 for the past 30 years, but I really need my mountain bike's lower gearing (46-38-28/12-13-15-17-19-21-24-28) for a couple of steep and long local climbs. Today's lower gears do make physiological sense, and, as pointed out above, we now have enough ratios to provide both reasonable ratiometric development and range, instead of trading one against the other, as we did in the Bad Old Days.
__________________
"Far and away the best prize that life offers is the chance to work hard at work worth doing." --Theodore Roosevelt
Capo: 1959 Modell Campagnolo, S/N 40324; 1960 Sieger (2), S/N 42624, 42597
Carlton: 1962 Franco Suisse, S/N K7911
Peugeot: 1970 UO-8, S/N 0010468
Bianchi: 1982 Campione d'Italia, S/N 1.M9914
Schwinn: 1988 Project KOM-10, S/N F804069
John E is offline  
Old 08-25-22, 06:50 PM
  #21  
bikemig 
Senior Member
 
bikemig's Avatar
 
Join Date: Apr 2012
Location: Middle Earth (aka IA)
Posts: 20,505

Bikes: A bunch of old bikes and a few new ones

Mentioned: 178 Post(s)
Tagged: 0 Thread(s)
Quoted: 5877 Post(s)
Liked 3,445 Times in 2,066 Posts
I ride old bikes and I like triples. For serious climbs, I like a 28 running on a 24 or a 28. For my local rides a 38/24 works fine but there is nothing steeper than a 10% grade locally and those climbs aren't too long.

One of the reasons I like fixing up old French bikes is that many of the stronglight cranks that came stock on those bikes let you run smaller chain rings, simplex RDs can generally handle larger freewheels, and there is generally clearance for a 28 or even a 32c tire. So some of the design choices we see on modern bikes have been around for a while in some fashion or other (and even before the mountain bike).

This is my 1982 Peugeot PXN 10: 50/38 rings, 13-28 6 speed freewheel, and 28c tires. The rear derailleur that came stock on the bike can handle up to 30 teeth.



Last edited by bikemig; 08-25-22 at 07:02 PM.
bikemig is offline  
Likes For bikemig:
Old 08-25-22, 06:52 PM
  #22  
downtube42
Senior Member
 
downtube42's Avatar
 
Join Date: Oct 2008
Location: Portland, OR
Posts: 3,803

Bikes: Trek Domane SL6 Gen 3, Soma Fog Cutter, Focus Mares AL, Detroit Bikes Sparrow FG, Volae Team, Nimbus MUni

Mentioned: 11 Post(s)
Tagged: 0 Thread(s)
Quoted: 878 Post(s)
Liked 2,019 Times in 1,055 Posts
BITD, when a pro racer cracked on a climb, he lost huge time because he couldn't turn the cranks over. Cracked meant something, physically and mentally. Destroyed. Done.

Now they downshift, recover, and carry on.
downtube42 is offline  
Likes For downtube42:
Old 08-25-22, 07:24 PM
  #23  
cyclezen
OM boy
 
cyclezen's Avatar
 
Join Date: Jul 2005
Location: Goleta CA
Posts: 4,340

Bikes: a bunch

Mentioned: 11 Post(s)
Tagged: 0 Thread(s)
Quoted: 502 Post(s)
Liked 623 Times in 425 Posts
Originally Posted by t2p
and traveling backward - 12-23 cogset was common before 12-25
unfortunate it took too long
but in flat areas it was probably less of an issue (if no issue)
iff'n you wanna go way back, 1st gen DuraAce was 10 spd (I mean the THE REAL 10 speed !) crank was 53/42 and freewheel 5 spd 13,14,15,17,19, as came on my Fuji 'The Ace'. Truly a leg breaker for any road courses. We all rejoiced when 6 spd freewheels became available - Ultra 7 ? impossible !!! could it get any better ???
LOL!
Ride On
Yuri
cyclezen is offline  
Likes For cyclezen:
Old 08-26-22, 01:30 PM
  #24  
Bald Paul
Senior Member
 
Bald Paul's Avatar
 
Join Date: Sep 2017
Location: Upstate SC
Posts: 1,680
Mentioned: 3 Post(s)
Tagged: 0 Thread(s)
Quoted: 806 Post(s)
Liked 1,612 Times in 764 Posts
Originally Posted by cyclezen
iff'n you wanna go way back, 1st gen DuraAce was 10 spd (I mean the THE REAL 10 speed !) crank was 53/42 and freewheel 5 spd 13,14,15,17,19, as came on my Fuji 'The Ace'. Truly a leg breaker for any road courses. We all rejoiced when 6 spd freewheels became available - Ultra 7 ? impossible !!! could it get any better ???
LOL!
Ride On
Yuri
Yup, my days of 52/42 cranksets and "corncob" 5 speed cassettes are well behind me now, along with my 27" X 19mm tires.
Now, it's a Rival 46/33 with a 10-36 12 speed cassette and nice, comfy 700C X 32 tires.

Last edited by Bald Paul; 08-27-22 at 02:11 PM.
Bald Paul is offline  
Likes For Bald Paul:
Old 08-27-22, 06:05 PM
  #25  
rydabent
Banned
 
Join Date: Apr 2010
Location: Lincoln Ne
Posts: 9,924

Bikes: RANS Stratus TerraTrike Tour II

Mentioned: 46 Post(s)
Tagged: 0 Thread(s)
Quoted: 3352 Post(s)
Liked 1,054 Times in 634 Posts
Originally Posted by Classtime
Saturday, I started with the local training ride which is attended by many accomplished and current 50 and 60+ National Champions. Of course, most have new bikes with electronic shifting and disk brakes. But what struck me was that most of these guys and gals had huge cogsets. Many of them went to 34! Now compact cranksets have been popular for some time but 34 tooth cogs on a road racing bike? Makes me think of doing that to my modern bike.
OTOH they will never have to get off and push their bikes up a really steep hill.
rydabent is offline  

Thread Tools
Search this Thread

Contact Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service -

Copyright © 2024 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.