Go Back  Bike Forums > Bike Forums > Bicycle Mechanics
Reload this Page >

B Screw question

Notices
Bicycle Mechanics Broken bottom bracket? Tacoed wheel? If you're having problems with your bicycle, or just need help fixing a flat, drop in here for the latest on bicycle mechanics & bicycle maintenance.

B Screw question

Old 08-02-22, 04:48 PM
  #1  
sknhgy 
Dirt Bomb
Thread Starter
 
sknhgy's Avatar
 
Join Date: Aug 2006
Location: Illinois
Posts: 2,857
Mentioned: 64 Post(s)
Tagged: 0 Thread(s)
Quoted: 5390 Post(s)
Liked 277 Times in 230 Posts
B Screw question

All the B Screw adjustment on my Shimano derailler is taken up and the pully JUST BARELY clears the largest cog. It might even be rubbing a little.

Since all the adjustment is taken up --- Should I remove a few links from the chain in order to get a little more clearance?

Thanks in advance.
__________________
sknhgy is offline  
Likes For sknhgy:
Old 08-02-22, 05:01 PM
  #2  
Bill Kapaun
Really Old Senior Member
 
Bill Kapaun's Avatar
 
Join Date: Feb 2007
Location: Mid Willamette Valley, Orygun
Posts: 13,822

Bikes: 87 RockHopper,2008 Specialized Globe. Both upgraded to 9 speeds.

Mentioned: 20 Post(s)
Tagged: 0 Thread(s)
Quoted: 1774 Post(s)
Liked 1,230 Times in 851 Posts
How many extra links can you SAFELY remove?


This is a quickie method to determine how much extra chain you have. No sense getting your hands dirty if you don't need to.
Put it in BIG:BIG Cog/chainring.
You want 1-2" excess. More than that can exacerbate your problem to some degree, depending on "how much"
Does the RDER have adequate chain wrap & cog size capacity.
IOW, what's different then before?
Bill Kapaun is offline  
Old 08-02-22, 05:02 PM
  #3  
Polaris OBark
ignominious poltroon
 
Polaris OBark's Avatar
 
Join Date: Jan 2022
Posts: 3,924
Mentioned: 3 Post(s)
Tagged: 0 Thread(s)
Quoted: 2184 Post(s)
Liked 3,336 Times in 1,741 Posts
I don't think shortening the chain would help. Buy a longer bolt (I think they are M4) at the hardware store -- strongest steel you can find, as you don't want it to start to bend.
Polaris OBark is offline  
Old 08-02-22, 05:24 PM
  #4  
70sSanO
Senior Member
 
70sSanO's Avatar
 
Join Date: Feb 2015
Location: Mission Viejo
Posts: 5,770

Bikes: 1986 Cannondale SR400 (Flat bar commuter), 1988 Cannondale Criterium XTR, 1992 Serotta T-Max, 1995 Trek 970

Mentioned: 20 Post(s)
Tagged: 0 Thread(s)
Quoted: 1935 Post(s)
Liked 2,148 Times in 1,312 Posts
Sometimes if a chain is too long, shortening it might help.

A longer bolt might help. The problem with longer bolts is keeping them on the hanger tab.

Some RD’s just have weak b springs. I found that with a couple of Shimano RD’s rated for 34t and 32t had an issue. On one bike I used a locknut on the end of the b screw to gain enough contact with the hanger tab. Not pretty, but it works.

John
70sSanO is online now  
Likes For 70sSanO:
Old 08-02-22, 05:47 PM
  #5  
andrewclaus
Senior Member
 
Join Date: Feb 2012
Location: Golden, CO and Tucson, AZ
Posts: 2,822

Bikes: 2016 Fuji Tread, 1983 Trek 520

Mentioned: 13 Post(s)
Tagged: 0 Thread(s)
Quoted: 669 Post(s)
Liked 725 Times in 422 Posts
Another hack is to turn the B screw around and have the head sit on the hanger.
andrewclaus is offline  
Likes For andrewclaus:
Old 08-03-22, 12:59 AM
  #6  
irtazasheikj
Newbie
 
Join Date: Aug 2022
Posts: 1
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 1 Post(s)
Likes: 0
Liked 0 Times in 0 Posts
Buy a long chain, if you can. Otherwise, removing chains would not help.
irtazasheikj is offline  
Old 08-03-22, 04:52 AM
  #7  
hokiefyd 
Senior Member
 
hokiefyd's Avatar
 
Join Date: Feb 2017
Location: Northern Shenandoah Valley
Posts: 4,123

Bikes: More bikes than riders

Mentioned: 36 Post(s)
Tagged: 0 Thread(s)
Quoted: 1438 Post(s)
Liked 749 Times in 559 Posts
With most traditional style derailers, where the upper pulley is on a different axis than the top of the cage (and swings up vertically as the cage rotates rearward), shortening the chain can absolutely buy you some room here.

As Bill Kapaun suggested, put the drivetrain in the big-big configuration to see if you can shorten it some. If you determine that you can indeed remove one inner and outer link pair, then put the drivetrain back in the low gear combination and use a small piece of wire or two small screwdrivers as pictured above to mock up what your derailleur cage and upper pulley will do with that one link pair removed. It may rotate that cage just forward enough to sneak that upper pulley down out of the largest sprocket.

A longer chain will not help in this case -- it will generally make the problem worse. A longer chain allows the cage to pull further rearward, which will cause the upper pulley to ride even higher.

And all of the above, again, assumes a traditional style derailer. This does not apply to some of the Shimano Shadows or SRAMs where the upper pulley is mounted coincident with the upper cage pivot. In that case, the upper pulley does NOT move vertically as the cage swings, and chain length should not have an effect on upper pulley position.
hokiefyd is offline  
Old 08-03-22, 06:02 AM
  #8  
sknhgy 
Dirt Bomb
Thread Starter
 
sknhgy's Avatar
 
Join Date: Aug 2006
Location: Illinois
Posts: 2,857
Mentioned: 64 Post(s)
Tagged: 0 Thread(s)
Quoted: 5390 Post(s)
Liked 277 Times in 230 Posts
Thanks. I'm gonna try a longer bolt and see if that works. This is a fairly old bike. At one time or another I might have replaced the chain without comparing it to the one I was replacing.
Or I might have changed cassette/cog size and not adjusted chain length accordingly. But I'm just guessing here.
__________________

Last edited by sknhgy; 08-03-22 at 06:06 AM.
sknhgy is offline  
Old 08-03-22, 09:31 AM
  #9  
cxwrench
Senior Member
 
cxwrench's Avatar
 
Join Date: Jul 2013
Location: Nor-Cal
Posts: 3,767

Bikes: lots

Mentioned: 7 Post(s)
Tagged: 0 Thread(s)
Quoted: 1958 Post(s)
Liked 2,932 Times in 1,489 Posts
Originally Posted by irtazasheikj
Buy a long chain, if you can. Otherwise, removing chains would not help.
What are you trying to say here?
cxwrench is offline  
Likes For cxwrench:
Old 08-03-22, 09:47 PM
  #10  
easyupbug 
Senior Member
 
Join Date: Jan 2013
Posts: 2,652

Bikes: too many sparkly Italians, some sweet Americans and a couple interesting Japanese

Mentioned: 9 Post(s)
Tagged: 0 Thread(s)
Quoted: 560 Post(s)
Liked 546 Times in 396 Posts
You can try as some have said:
reversing the B screw but that makes adjustment messy
add a nut to the end of the screw for more surface area
get a longer screw
do check you hanger and derailleur incase they are bent
shorten the chain don't buy a longer chain!
easyupbug is offline  
Old 08-03-22, 09:55 PM
  #11  
Leisesturm
Senior Member
 
Join Date: Jul 2005
Posts: 5,968
Mentioned: 26 Post(s)
Tagged: 0 Thread(s)
Quoted: 2473 Post(s)
Liked 722 Times in 513 Posts
What about those Wolf Tooth things that let the RD ride lower to clear a big cog?
Leisesturm is offline  
Old 08-04-22, 06:46 AM
  #12  
sknhgy 
Dirt Bomb
Thread Starter
 
sknhgy's Avatar
 
Join Date: Aug 2006
Location: Illinois
Posts: 2,857
Mentioned: 64 Post(s)
Tagged: 0 Thread(s)
Quoted: 5390 Post(s)
Liked 277 Times in 230 Posts
I ended up taking a few links out of the chain. Don't know if its my imagination, but would that make it so my shift levers require more effort to push?

The longer screw didn't work. Hard to explain but it didn't line up.
__________________
sknhgy is offline  
Old 08-04-22, 07:07 AM
  #13  
rccardr 
aka: Dr. Cannondale
 
rccardr's Avatar
 
Join Date: Jul 2009
Posts: 7,852
Mentioned: 234 Post(s)
Tagged: 0 Thread(s)
Quoted: 2151 Post(s)
Liked 3,380 Times in 1,198 Posts
If the bike has horizontal rear dropouts you can unscrew or remove the setscrews and pull the wheel back as far as it will go.
Will require adjusting rear brake shoes.
Usually gives you that extra little bit of clearance between the upper pulley and largest cog when in small/big.
__________________
Hard at work in the Secret Underground Laboratory...
rccardr is offline  
Old 08-04-22, 08:19 AM
  #14  
andrewclaus
Senior Member
 
Join Date: Feb 2012
Location: Golden, CO and Tucson, AZ
Posts: 2,822

Bikes: 2016 Fuji Tread, 1983 Trek 520

Mentioned: 13 Post(s)
Tagged: 0 Thread(s)
Quoted: 669 Post(s)
Liked 725 Times in 422 Posts
Originally Posted by sknhgy
I ended up taking a few links out of the chain. Don't know if its my imagination, but would that make it so my shift levers require more effort to push?

The longer screw didn't work. Hard to explain but it didn't line up.
In post #4 you got some warning about a longer screw not hitting the hanger tab. That was the reason for the suggestion to turn the screw around.

If you made the chain too short, it could be very hard to shift into the large-large combination at least. It shouldn't make a noticeable change in small-small. Be sure you didn't put any crimps in the cable or housing.
andrewclaus is offline  
Old 08-05-22, 04:02 PM
  #15  
bikeme
Senior Member
 
Join Date: May 2001
Location: Sunny so. cal.
Posts: 904
Mentioned: 1 Post(s)
Tagged: 0 Thread(s)
Quoted: 136 Post(s)
Liked 57 Times in 31 Posts
Almost touching is way too close. I was misled by Shimano instructions of having it very close for years. I've found that 5mm between the largest cog's and pulley's teeth is great. Yields plenty of chain wrap on big cog and quieter drivetrain. Per the attached video, also check the b-tension with the chain in big ring and highest cog so there's no belly in the chain (provided chain is proper length). Kyle is does a great job of explaining what b-tension actually does and how to adjust it! FYI, he's a mtb guy but info applies to road bikes too. EDIT: additional thought--if this is a mtb with an after-market extra big gear, you might need a longer (like 25mm) b-tension screw that the RD originally came with.


Last edited by bikeme; 08-05-22 at 04:06 PM.
bikeme is offline  
Old 08-06-22, 12:33 PM
  #16  
3alarmer 
Friendship is Magic
 
3alarmer's Avatar
 
Join Date: Nov 2010
Location: Sacramento, CA
Posts: 22,931

Bikes: old ones

Mentioned: 304 Post(s)
Tagged: 0 Thread(s)
Quoted: 26245 Post(s)
Liked 10,229 Times in 7,098 Posts
...
...if it's a "fairly old bike" there are some limitations on the largest cog many of the older rear derailleurs will accept.
Sometimes, you can push that another dog or two, but it's generally a bad idea. They still work then, but not well.

You can look up a lot of the capacity numbers for older derailleurs on VeloBase: link
__________________
3alarmer is online now  
Old 08-06-22, 01:16 PM
  #17  
Bill Kapaun
Really Old Senior Member
 
Bill Kapaun's Avatar
 
Join Date: Feb 2007
Location: Mid Willamette Valley, Orygun
Posts: 13,822

Bikes: 87 RockHopper,2008 Specialized Globe. Both upgraded to 9 speeds.

Mentioned: 20 Post(s)
Tagged: 0 Thread(s)
Quoted: 1774 Post(s)
Liked 1,230 Times in 851 Posts
Originally Posted by sknhgy
I ended up taking a few links out of the chain. Don't know if its my imagination, but would that make it so my shift levers require more effort to push?

The longer screw didn't work. Hard to explain but it didn't line up.
Do you have the proper amount of slack as shown in POST #2?
Bill Kapaun is offline  
Old 08-06-22, 01:49 PM
  #18  
79pmooney
Senior Member
 
79pmooney's Avatar
 
Join Date: Oct 2014
Location: Portland, OR
Posts: 12,825

Bikes: (2) ti TiCycles, 2007 w/ triple and 2011 fixed, 1979 Peter Mooney, ~1983 Trek 420 now fixed and ~1973 Raleigh Carlton Competition gravel grinder

Mentioned: 128 Post(s)
Tagged: 0 Thread(s)
Quoted: 4742 Post(s)
Liked 3,860 Times in 2,509 Posts
Question - is this a place where a Wolf Tooth hanger extender can be used? I thought that was what they were for. (But what do I know. I'm still at 28 teeth and downsizing chainrings.)
79pmooney is offline  
Old 08-06-22, 03:02 PM
  #19  
cxwrench
Senior Member
 
cxwrench's Avatar
 
Join Date: Jul 2013
Location: Nor-Cal
Posts: 3,767

Bikes: lots

Mentioned: 7 Post(s)
Tagged: 0 Thread(s)
Quoted: 1958 Post(s)
Liked 2,932 Times in 1,489 Posts
Originally Posted by 79pmooney
Question - is this a place where a Wolf Tooth hanger extender can be used? I thought that was what they were for. (But what do I know. I'm still at 28 teeth and downsizing chainrings.)
Wolf Tooth hanger extenders do only 1 of the 2 things a derailleur needs to do and they don't even do that well. I cannot stand those things. They move the derailleur down, that's all. That will allow a larger cog than the derailleur is spec'd to work with...BUT...they make the upper pulley further from the cogs and shifting suffers. The other thing they can't do is magically make the pulley cage longer so it won't wrap the extra chain you'll need for the bigger cogs/longer cage. People blindly suggest them but don't have the basic knowledge to know why they don't work. It even says that right on the WT site.
d
cxwrench is offline  
Likes For cxwrench:
Old 08-06-22, 04:38 PM
  #20  
Iride01 
I'm good to go!
 
Iride01's Avatar
 
Join Date: Jul 2017
Location: Mississippi
Posts: 14,809

Bikes: Tarmac Disc Comp Di2 - 2020

Mentioned: 50 Post(s)
Tagged: 0 Thread(s)
Quoted: 6099 Post(s)
Liked 4,730 Times in 3,260 Posts
Shimano says they should be as close as possible without touching. You only said they might be rubbing. Did you ever find out? Here is what Shimano said for my rear DR on a past bike...

Adjusting the B-tension adjust bolt

Mount the chain on the smallest chainring and the largest sprocket, and turn the crank arm backward. Turn the B-tension adjust bolt to adjust the guide pulley to be as close to the sprocket as possible but not so close that it touches. Next, set the chain to the smallest sprocket and repeat the above to make sure that the pulley does not touch the sprocket.
page 14 https://si.shimano.com/en/pdfs/dm/RD...003-09-ENG.pdf
Iride01 is online now  
Likes For Iride01:
Old 08-06-22, 05:09 PM
  #21  
sknhgy 
Dirt Bomb
Thread Starter
 
sknhgy's Avatar
 
Join Date: Aug 2006
Location: Illinois
Posts: 2,857
Mentioned: 64 Post(s)
Tagged: 0 Thread(s)
Quoted: 5390 Post(s)
Liked 277 Times in 230 Posts
Originally Posted by Bill Kapaun
Do you have the proper amount of slack as shown in POST #2?
Actually, I wasn't clear what to look for using that test.
I took the bike out for a couple hours today. The levers did seem a bit stiffer than normal. But it shifted good.
__________________
sknhgy is offline  
Old 08-06-22, 05:28 PM
  #22  
Bill Kapaun
Really Old Senior Member
 
Bill Kapaun's Avatar
 
Join Date: Feb 2007
Location: Mid Willamette Valley, Orygun
Posts: 13,822

Bikes: 87 RockHopper,2008 Specialized Globe. Both upgraded to 9 speeds.

Mentioned: 20 Post(s)
Tagged: 0 Thread(s)
Quoted: 1774 Post(s)
Liked 1,230 Times in 851 Posts
Originally Posted by sknhgy
Actually, I wasn't clear what to look for using that test.
I took the bike out for a couple hours today. The levers did seem a bit stiffer than normal. But it shifted good.
What was difficult to understand about "You want 1-2" excess..."?
Bill Kapaun is offline  
Old 08-07-22, 07:50 PM
  #23  
cxwrench
Senior Member
 
cxwrench's Avatar
 
Join Date: Jul 2013
Location: Nor-Cal
Posts: 3,767

Bikes: lots

Mentioned: 7 Post(s)
Tagged: 0 Thread(s)
Quoted: 1958 Post(s)
Liked 2,932 Times in 1,489 Posts
You're kidding, right? Bill explained it WITH a photo. Put the bike in big/big. Use the screwdriver/whatever to see if you can pull any extra slack.
cxwrench is offline  
Old 08-08-22, 09:41 AM
  #24  
sknhgy 
Dirt Bomb
Thread Starter
 
sknhgy's Avatar
 
Join Date: Aug 2006
Location: Illinois
Posts: 2,857
Mentioned: 64 Post(s)
Tagged: 0 Thread(s)
Quoted: 5390 Post(s)
Liked 277 Times in 230 Posts
Originally Posted by Bill Kapaun
What was difficult to understand about "You want 1-2" excess..."?
Originally Posted by cxwrench
You're kidding, right? Bill explained it WITH a photo. Put the bike in big/big. Use the screwdriver/whatever to see if you can pull any extra slack.
You guys aren't explaining yourselves well. All you are saying is to pinch the chain. Then you get snippy when a person doesn't understand what to be looking for. Here's a couple other threads where the same thing went down:

https://www.bikeforums.net/bicycle-m...ut-pedals.html
https://www.bikeforums.net/bicycle-m...-new-gear.html

But it's OK. There's always Youtube to help us.
__________________

Last edited by sknhgy; 08-08-22 at 09:44 AM.
sknhgy is offline  
Old 08-08-22, 09:51 AM
  #25  
cxwrench
Senior Member
 
cxwrench's Avatar
 
Join Date: Jul 2013
Location: Nor-Cal
Posts: 3,767

Bikes: lots

Mentioned: 7 Post(s)
Tagged: 0 Thread(s)
Quoted: 1958 Post(s)
Liked 2,932 Times in 1,489 Posts
Originally Posted by sknhgy
You guys aren't explaining yourselves well. All you are saying is to pinch the chain. Then you get snippy when a person doesn't understand what to be looking for. Here's a couple other threads where the same thing went down:

https://www.bikeforums.net/bicycle-m...ut-pedals.html
https://www.bikeforums.net/bicycle-m...-new-gear.html

But it's OK. There's always Youtube to help us.
I can't imagine it being explained any better. If you don't understand what is being done in Bill's photo I don't know what to say. One more time...shift the bike into big/big (carefully in case there isn't enough chain) then put the screwdrivers in the chain as shown in the photo. If there's enough slack to do that you're good to go. I just twist the chain w/ my fingers but if you don't want to get dirty use the 2 small screwdrivers. If you need a video to make that more easily understood then watch a video. At that point it should be crystal clear.
cxwrench is offline  

Thread Tools
Search this Thread

Contact Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service -

Copyright © 2024 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.