Go Back  Bike Forums > Bike Forums > Classic & Vintage
Reload this Page >

Cables cutting into bottom bracket

Notices
Classic & Vintage This forum is to discuss the many aspects of classic and vintage bicycles, including musclebikes, lightweights, middleweights, hi-wheelers, bone-shakers, safety bikes and much more.

Cables cutting into bottom bracket

Old 03-13-21, 01:54 PM
  #1  
lajt
Newbie
Thread Starter
 
Join Date: Mar 2021
Location: Los Angeles, CA
Posts: 49
Mentioned: 3 Post(s)
Tagged: 0 Thread(s)
Quoted: 20 Post(s)
Liked 14 Times in 12 Posts
Cables cutting into bottom bracket

I bought an 80s frame which I'm building up and wondering if there's a better way than letting the cables keep cutting into the bottom bracket shell.
For comparison, the red bike is my Bridgestone RB-2, which has a plastic guide.
Sheldon Brown recommends a scrap of shifter housing, which he says will stay in place due to the tension.
Elsewhere on the web I saw suggestions to try heat shrink tubing, or something called jagwire housing.
Sheldon also says you can drill and tap a new hole to install a plastic cable guide.
If you drill a hole, how do you keep the screw from hitting a sealed cartridge bearing?
For the scrap of shifter housing trick, does it really stay in place purely from cable tension?

lajt is offline  
Likes For lajt:
Old 03-13-21, 02:11 PM
  #2  
repechage
Senior Member
 
Join Date: Jun 2006
Posts: 20,315
Mentioned: 129 Post(s)
Tagged: 0 Thread(s)
Quoted: 3447 Post(s)
Liked 2,786 Times in 1,967 Posts
A section of cable inner lining, should do the trick
repechage is offline  
Likes For repechage:
Old 03-13-21, 02:40 PM
  #3  
SurferRosa
Banned
 
Join Date: Dec 2018
Location: Pac NW
Posts: 8,761

Bikes: '70s - '80s Campagnolo

Mentioned: 92 Post(s)
Tagged: 0 Thread(s)
Quoted: 3844 Post(s)
Liked 6,434 Times in 3,181 Posts
I wouldn't use anything. Just clean it really well. Remove any burrs. Maybe add a tiny amount of wd-40 after you install the cables. Generally, the designer/manufacturer did not use any liner on his builds.
SurferRosa is offline  
Old 03-13-21, 02:57 PM
  #4  
lajt
Newbie
Thread Starter
 
Join Date: Mar 2021
Location: Los Angeles, CA
Posts: 49
Mentioned: 3 Post(s)
Tagged: 0 Thread(s)
Quoted: 20 Post(s)
Liked 14 Times in 12 Posts
Thanks for the perspective from both of you.
Repechage, what is cable inner lining? The soft plastic part of the housing if you cut away the metal outside?
SurferRosa, you might be right that some lube in there and maybe it will slide fairly friction free that now there's already a channel worn away after 30 years.
lajt is offline  
Old 03-13-21, 03:01 PM
  #5  
lajt
Newbie
Thread Starter
 
Join Date: Mar 2021
Location: Los Angeles, CA
Posts: 49
Mentioned: 3 Post(s)
Tagged: 0 Thread(s)
Quoted: 20 Post(s)
Liked 14 Times in 12 Posts
I wonder how long it would take before it would actually cut its way completely through?
It reminds me of a MythBusters episode where they tested whether you could cut through jail cell bars with dental floss. They rigged up a machine that pulled a loop of floss around the bar for a few days. It did cut through a minuscule amount--almost just an etching really. Their estimate of actually cutting through was something insane like a year of 24/7 cutting.
lajt is offline  
Old 03-13-21, 03:33 PM
  #6  
Steel1
Junior Member
 
Join Date: Jan 2018
Posts: 143
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 44 Post(s)
Liked 113 Times in 52 Posts
You can search Amazon for example of the housing, it is cheap.

“Jagwire Black Housing Liner 30 Meter Roll, Fits up to 1.8mm Cables” $12.99


I just bought several feet at local bike shop for a few dollars.


Steel1 is offline  
Likes For Steel1:
Old 03-13-21, 03:40 PM
  #7  
ridelikeaturtle
Senior Member
 
ridelikeaturtle's Avatar
 
Join Date: Nov 2015
Location: Dublin, Ireland
Posts: 1,259

Bikes: Bianchi Ti Megatube; Colnago Competition; Planet-X EC-130E; Klein Pulse; Amp Research B4; Litespeed Catalyst; Trek Y11

Mentioned: 8 Post(s)
Tagged: 0 Thread(s)
Quoted: 596 Post(s)
Liked 476 Times in 258 Posts
What's stopping you from just running a piece of housing over the cable at that location? Doesn't cost you anything to try.
ridelikeaturtle is offline  
Old 03-13-21, 04:57 PM
  #8  
canklecat
Me duelen las nalgas
 
canklecat's Avatar
 
Join Date: Aug 2015
Location: Texas
Posts: 13,519

Bikes: Centurion Ironman, Trek 5900, Univega Via Carisma, Globe Carmel

Mentioned: 199 Post(s)
Tagged: 0 Thread(s)
Quoted: 4555 Post(s)
Liked 2,791 Times in 1,795 Posts
If you don't have any cable liner handy, a cotton swab with hollow plastic stem will do. That's what I use on my bikes after my last bit of cable liner ran out. Snip off the cotton ball ends. The stem is hollow and just the right size for most shifter and brake cables. I use 'em on my bottom brackets and the convoluted metal guide noodles brazed onto the seat cluster on my old Univega with cantilever brakes.

Works great. Reduces cable friction a little too.
canklecat is offline  
Likes For canklecat:
Old 03-13-21, 05:08 PM
  #9  
Dean51 
Senior Member
 
Dean51's Avatar
 
Join Date: Feb 2016
Location: Olympic Peninsula, WA
Posts: 650

Bikes: '8? Ciocc Mockba 80, '82 Ron Cooper, '84 Allez, '86 Tommasini Racing, '86? Klein Quantum, '87 Ciocc Designer 84, '95 Trek 5500, '98 Litespeed Classic, '98 S-Works Mtb

Mentioned: 34 Post(s)
Tagged: 0 Thread(s)
Quoted: 226 Post(s)
Liked 307 Times in 121 Posts
Originally Posted by repechage
A section of cable inner lining, should do the trick
I've done this on my bikes....for shift cables that run below as well as above the bottom bracket. I haven't been concerned about the cable wearing on the metal, I'm just trying to preserve the paint / eliminate a potential rust spot. Short pieces of inner cable lining stay in place nicely.

Dean
__________________
Roll Me Up and Smoke Me When I Die

Last edited by Dean51; 03-13-21 at 05:12 PM.
Dean51 is offline  
Old 03-13-21, 09:04 PM
  #10  
Seanaus
Junior Member
 
Join Date: Jul 2020
Location: Australia
Posts: 132
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 33 Post(s)
Liked 123 Times in 50 Posts
Shimano Y80098100 is what I use, essentially the same as the Jagwire version mentioned previously. Stays in place fine.
Seanaus is offline  
Old 03-13-21, 09:35 PM
  #11  
cudak888 
www.theheadbadge.com
 
cudak888's Avatar
 
Join Date: Sep 2005
Location: Southern Florida
Posts: 28,487

Bikes: https://www.theheadbadge.com

Mentioned: 121 Post(s)
Tagged: 0 Thread(s)
Quoted: 2395 Post(s)
Liked 4,337 Times in 2,070 Posts
Originally Posted by ridelikeaturtle
What's stopping you from just running a piece of housing over the cable at that location? Doesn't cost you anything to try.
A thick piece of full housing could allow the cable to pop to the side if the lever is downshifted when the chain isn't moving, as the cable housing strands will be working against the curve of the cable.

Granted, the cable popping off one of the grooves is a possibility even with the thin lining - but it's less likely to go wrong, looks neater, and is easier to set with hot glue in a discreet manner.

-Kurt
__________________












cudak888 is offline  
Likes For cudak888:
Old 03-13-21, 09:52 PM
  #12  
lajt
Newbie
Thread Starter
 
Join Date: Mar 2021
Location: Los Angeles, CA
Posts: 49
Mentioned: 3 Post(s)
Tagged: 0 Thread(s)
Quoted: 20 Post(s)
Liked 14 Times in 12 Posts
Smart idea about hot glue! I use it for all the kids' art projects, but didn't think of it for this.
Is the cable liner easy to extract from a scrap piece of housing? Do you tug it out with needlenose pliers? Or use a utility knife to scrape off the outer coating and then peel off the strands of housing body?
lajt is offline  
Old 03-13-21, 11:04 PM
  #13  
repechage
Senior Member
 
Join Date: Jun 2006
Posts: 20,315
Mentioned: 129 Post(s)
Tagged: 0 Thread(s)
Quoted: 3447 Post(s)
Liked 2,786 Times in 1,967 Posts
Originally Posted by lajt
I wonder how long it would take before it would actually cut its way completely through?
It reminds me of a MythBusters episode where they tested whether you could cut through jail cell bars with dental floss. They rigged up a machine that pulled a loop of floss around the bar for a few days. It did cut through a minuscule amount--almost just an etching really. Their estimate of actually cutting through was something insane like a year of 24/7 cutting.
neurosurgeons use a diamond coated cable to saw through skull ( well they used to- most use a buzzy saw now ) takes a lot of time.
advantage is the cable saw kerf will be at an angle- staples not required to put it all back together. I know, too much information.
the chances of sawing through the bottom bracket shell by shifting - nada.
Aztec brand cables had a Teflon impregnated cable that slipped well. I use it on a bike with early under the BB cable guides- no room for liner.
repechage is offline  
Likes For repechage:
Old 03-14-21, 04:43 AM
  #14  
P!N20
Senior Member
 
P!N20's Avatar
 
Join Date: Aug 2010
Location: Wurundjeri Country
Posts: 2,443
Mentioned: 32 Post(s)
Tagged: 0 Thread(s)
Quoted: 1072 Post(s)
Liked 1,868 Times in 916 Posts
+1 for cable liner. Although I do find the cable eventually saws through the liner - takes a while though and is cheap to replace.
P!N20 is offline  
Old 03-14-21, 05:14 AM
  #15  
gearbasher
Senior Member
 
gearbasher's Avatar
 
Join Date: May 2009
Location: Sitting on my butt in front of a computer
Posts: 1,532
Mentioned: 15 Post(s)
Tagged: 0 Thread(s)
Quoted: 439 Post(s)
Liked 830 Times in 363 Posts
Originally Posted by lajt
I wonder how long it would take before it would actually cut its way completely through?
.
I've always left the bare cables on all my bikes. The most wear I experienced was on an Alan aluminum frame. The cable cut into the BB about half the thickness of the cable. That was after 55,000 miles. Then seat lug cracked and that frame went to the great recycler in the sky. Let me add, I shift a lot.
gearbasher is offline  
Old 03-14-21, 05:18 AM
  #16  
Johno59
Senior Member
 
Join Date: Oct 2016
Location: Cambridge UK
Posts: 852

Bikes: 1903 24 spd Sunbeam, 1927 Humber, 3 1930 Raleighs, 2 1940s Sunbeams, 2 1940s Raleighs, Rudge, 1950s Robin Hood, 1958 Claud Butler, 2 1973 Colnago Supers, Eddie Merckx, 2 1980 Holdsworth, EG Bates funny TT bike, another 6 or so 1990s bikes

Mentioned: 15 Post(s)
Tagged: 0 Thread(s)
Quoted: 331 Post(s)
Liked 331 Times in 185 Posts
There's a lotta salt hitting this area so I would be careful using something that salty water can creep into. Just make certain when you wash your bike to keep this area nice and clean and waxed.
Johno59 is offline  
Old 03-14-21, 06:42 AM
  #17  
rccardr 
aka: Dr. Cannondale
 
rccardr's Avatar
 
Join Date: Jul 2009
Posts: 7,839
Mentioned: 234 Post(s)
Tagged: 0 Thread(s)
Quoted: 2144 Post(s)
Liked 3,372 Times in 1,193 Posts
OP lives is California, no salt used there.
Nothing is really required, but cable lining will ensure a nice, smooth shift. Most bike shops will give you the 6-8 inches needed for this task.
__________________
Hard at work in the Secret Underground Laboratory...
rccardr is offline  
Old 03-14-21, 12:19 PM
  #18  
unworthy1
Stop reading my posts!
 
unworthy1's Avatar
 
Join Date: Sep 2004
Posts: 12,930
Mentioned: 89 Post(s)
Tagged: 0 Thread(s)
Quoted: 1408 Post(s)
Liked 1,025 Times in 760 Posts
Originally Posted by rccardr
OP lives is California, no salt used there.
Nothing is really required, but cable lining will ensure a nice, smooth shift. Most bike shops will give you the 6-8 inches needed for this task.
No, not ALL of California is "Malibu Barbie Land".
"SACRAMENTO (CBS13) — As the winter storm continues, so do Caltrans crews who are hard at work treating and clearing snow-covered roads. ... Now they use a sand-salt mixture and pre-treat roads with a mixture of water and salt that prevents freezing."
unworthy1 is offline  
Likes For unworthy1:
Old 03-14-21, 06:06 PM
  #19  
lajt
Newbie
Thread Starter
 
Join Date: Mar 2021
Location: Los Angeles, CA
Posts: 49
Mentioned: 3 Post(s)
Tagged: 0 Thread(s)
Quoted: 20 Post(s)
Liked 14 Times in 12 Posts
That is true, some of CA gets a lot of snow! It always amazes me when I read that Mammoth has, say, 10 feet of snow in a really snowy winter. I actually live in the Los Angeles area, so it's pretty snow-free here (although Malibu had a freak storm a couple of months ago and did get a little dusting of snow). I bought the frame from Rccardr which is how he knew that.
lajt is offline  
Old 03-17-21, 05:56 AM
  #20  
Johno59
Senior Member
 
Join Date: Oct 2016
Location: Cambridge UK
Posts: 852

Bikes: 1903 24 spd Sunbeam, 1927 Humber, 3 1930 Raleighs, 2 1940s Sunbeams, 2 1940s Raleighs, Rudge, 1950s Robin Hood, 1958 Claud Butler, 2 1973 Colnago Supers, Eddie Merckx, 2 1980 Holdsworth, EG Bates funny TT bike, another 6 or so 1990s bikes

Mentioned: 15 Post(s)
Tagged: 0 Thread(s)
Quoted: 331 Post(s)
Liked 331 Times in 185 Posts
There's always snow in CA. Some of it goes on the road and some it goes elsewhere.

OMG I can see your BB is worn!

Last edited by Johno59; 03-17-21 at 06:00 AM.
Johno59 is offline  
Likes For Johno59:
Old 03-17-21, 09:20 AM
  #21  
SJX426 
Senior Member
 
SJX426's Avatar
 
Join Date: May 2008
Location: Fredericksburg, Va
Posts: 9,563

Bikes: '65 Frejus TDF, '73 Bottecchia Giro d'Italia, '83 Colnago Superissimo, '84 Trek 610, '84 Trek 760, '88 Pinarello Veneto, '88 De Rosa Pro, '89 Pinarello Montello, '94 Burley Duet, 97 Specialized RockHopper, 2010 Langster, Tern Link D8

Mentioned: 73 Post(s)
Tagged: 0 Thread(s)
Quoted: 1598 Post(s)
Liked 2,181 Times in 1,086 Posts
I think you can tell how much a bike is used by how deep the groves are. Wish there was a depth to years/miles/shift chart!
P1030586 on Flickr
P1040813 on Flickr
P1040818 on Flickr
__________________
Bikes don't stand alone. They are two tired.
SJX426 is offline  
Likes For SJX426:
Old 03-17-21, 10:01 AM
  #22  
Johno59
Senior Member
 
Join Date: Oct 2016
Location: Cambridge UK
Posts: 852

Bikes: 1903 24 spd Sunbeam, 1927 Humber, 3 1930 Raleighs, 2 1940s Sunbeams, 2 1940s Raleighs, Rudge, 1950s Robin Hood, 1958 Claud Butler, 2 1973 Colnago Supers, Eddie Merckx, 2 1980 Holdsworth, EG Bates funny TT bike, another 6 or so 1990s bikes

Mentioned: 15 Post(s)
Tagged: 0 Thread(s)
Quoted: 331 Post(s)
Liked 331 Times in 185 Posts
Slip sliding away

They question I'd like answered is there any difference with the insert and what happens when the cable starts cutting through the piece of outer.
Johno59 is offline  
Old 03-17-21, 12:34 PM
  #23  
francophile 
PM me your cotters
 
francophile's Avatar
 
Join Date: Jun 2015
Location: ATL
Posts: 3,916
Mentioned: 80 Post(s)
Tagged: 0 Thread(s)
Quoted: 1137 Post(s)
Liked 588 Times in 420 Posts
@lajt if you're in LA area and don't mind waiting a few days, I have a whole roll of that Jagwire liner, I use it on the kids bikes to cut down on cable rust.

Shoot me a PM with an address, I'll sent you a few feet. I'll literally never get through this roll otherwise.
__________________
███████████████

francophile is offline  
Old 03-17-21, 12:44 PM
  #24  
tiger1964 
Senior Member
 
tiger1964's Avatar
 
Join Date: Apr 2011
Location: Maryland, USA
Posts: 2,387

Bikes: Drysdale/Gitane/Zeus/Masi/Falcon/Palo Alto/Raleigh/Legnano

Mentioned: 34 Post(s)
Tagged: 0 Thread(s)
Quoted: 955 Post(s)
Liked 603 Times in 388 Posts
Wow, I am beginning to understand the plastic under-BB guides secured with a thorough-bolt.

Originally Posted by SJX426
I think you can tell how much a bike is used by how deep the groves are. Wish there was a depth to years/miles/shift chart!
__________________
Larry:1958 Drysdale, 1961 Gitane Gran Sport, 1974 Zeus track, 1988 Masi Gran Corsa, 1974 Falcon, 1980 Palo Alto, 1973 Raleigh Gran Sport, 1974 Legnano. Susan: 1976 Windsor Profesional.


tiger1964 is offline  
Old 03-17-21, 01:10 PM
  #25  
squirtdad
Senior Member
 
squirtdad's Avatar
 
Join Date: Jul 2006
Location: San Jose (Willow Glen) Ca
Posts: 9,831

Bikes: Kirk Custom JK Special, '84 Team Miyata,(dura ace old school) 80?? SR Semi-Pro 600 Arabesque

Mentioned: 104 Post(s)
Tagged: 0 Thread(s)
Quoted: 2296 Post(s)
Liked 2,710 Times in 1,483 Posts
cable liner for the win i also have a roll of it and would put some in an envelope if people needed
__________________
Life is too short not to ride the best bike you have, as much as you can
(looking for Torpado Super light frame/fork or for Raleigh International frame fork 58cm)



squirtdad is offline  

Thread Tools
Search this Thread

Contact Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service -

Copyright © 2024 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.