Go Back  Bike Forums > Bike Forums > Road Cycling
Reload this Page >

What's your disc brake pad mileage?

Notices
Road Cycling “It is by riding a bicycle that you learn the contours of a country best, since you have to sweat up the hills and coast down them. Thus you remember them as they actually are, while in a motor car only a high hill impresses you, and you have no such accurate remembrance of country you have driven through as you gain by riding a bicycle.” -- Ernest Hemingway

What's your disc brake pad mileage?

Old 08-01-22, 08:08 AM
  #1  
TakingMyTime
Senior Member
Thread Starter
 
Join Date: Aug 2012
Location: Los Alamitos, Calif.
Posts: 2,478

Bikes: Trek 7.4 FX

Mentioned: 4 Post(s)
Tagged: 0 Thread(s)
Quoted: 1026 Post(s)
Liked 912 Times in 535 Posts
What's your disc brake pad mileage?

I'm new to hydraulic discs. I've read several things here and there stating a wide range of mileage that one gets from their pads. I was just wondering how often you're replacing yours? I know it can be quite dependent on the environment your ride in. I'll be riding in dry weather on flat roads and probably never encounter rain.

Sorry if this is a rather N00b question but I'm starting from ground zero as far a disc experience goes. I guess I was just wondering if I should start to load up on pads when I see a sale on them.
TakingMyTime is online now  
Old 08-01-22, 09:03 AM
  #2  
Iride01 
I'm good to go!
 
Iride01's Avatar
 
Join Date: Jul 2017
Location: Mississippi
Posts: 14,800

Bikes: Tarmac Disc Comp Di2 - 2020

Mentioned: 50 Post(s)
Tagged: 0 Thread(s)
Quoted: 6099 Post(s)
Liked 4,730 Times in 3,260 Posts
5000 plus and counting. Still on my first set. I bought pads at about 3000 just to be ready.

Wide range of values you are seeing are likely because some people are in areas with high demands for braking and others are in areas where you can just let the hammer down for the entire ride.

I also suspect some ride the brakes more on turns and others are more confident of their line and speed through the turn.
Iride01 is offline  
Likes For Iride01:
Old 08-01-22, 09:08 AM
  #3  
Polaris OBark
ignominious poltroon
 
Polaris OBark's Avatar
 
Join Date: Jan 2022
Posts: 3,923
Mentioned: 3 Post(s)
Tagged: 0 Thread(s)
Quoted: 2184 Post(s)
Liked 3,336 Times in 1,741 Posts
Low. Under 1K. I ride lots of hills and abrasive dirt.
Polaris OBark is offline  
Old 08-01-22, 09:12 AM
  #4  
delbiker1 
Mother Nature's Son
 
delbiker1's Avatar
 
Join Date: Mar 2016
Location: Sussex County, Delaware
Posts: 3,111

Bikes: 2014 Orbea Avant MD30, 2004 Airborne Zeppelin TI, 2003 Lemond Poprad, 2001 Lemond Tourmalet, 2014? Soma Smoothie

Mentioned: 14 Post(s)
Tagged: 0 Thread(s)
Quoted: 838 Post(s)
Liked 1,414 Times in 801 Posts
I recently had to put new pads on the front of my Orbea Avant with Shimano mechanical disc brakes. I am estimating at least 6000 miles, max of 8,000. I have a new set for the rear, just have not done it yet. I live in flatland and do a lot of rural, small town riding, so braking is minimum, all pads last a long time.
delbiker1 is offline  
Old 08-01-22, 09:21 AM
  #5  
TakingMyTime
Senior Member
Thread Starter
 
Join Date: Aug 2012
Location: Los Alamitos, Calif.
Posts: 2,478

Bikes: Trek 7.4 FX

Mentioned: 4 Post(s)
Tagged: 0 Thread(s)
Quoted: 1026 Post(s)
Liked 912 Times in 535 Posts
Originally Posted by Iride01
5000 plus and counting. Still on my first set. I bought pads at about 3000 just to be ready.
Thanks. I'm nowhere near needing any yet but trying to source different parts being what it is nowadays I thought it would be good just to prepare and have them in my drawer.
TakingMyTime is online now  
Old 08-01-22, 10:49 AM
  #6  
WhyFi
Senior Member
 
WhyFi's Avatar
 
Join Date: Jan 2010
Location: TC, MN
Posts: 39,505

Bikes: R3 Disc, Haanjo

Mentioned: 353 Post(s)
Tagged: 1 Thread(s)
Quoted: 20791 Post(s)
Liked 9,436 Times in 4,663 Posts
I probably go through a set of rear pads once per year, so about 6,000 miles or so. I live in a fairly flattish metro area, so it's a lot of stop & go but not a lot of hard braking for descents or the like.
WhyFi is offline  
Likes For WhyFi:
Old 08-01-22, 11:59 AM
  #7  
Koyote
Senior Member
 
Join Date: Sep 2017
Posts: 7,763
Mentioned: 37 Post(s)
Tagged: 0 Thread(s)
Quoted: 6881 Post(s)
Liked 10,869 Times in 4,634 Posts
Originally Posted by TakingMyTime
I'm new to hydraulic discs. I've read several things here and there stating a wide range of mileage that one gets from their pads. I was just wondering how often you're replacing yours? I know it can be quite dependent on the environment your ride in. I'll be riding in dry weather on flat roads and probably never encounter rain.

Sorry if this is a rather N00b question but I'm starting from ground zero as far a disc experience goes. I guess I was just wondering if I should start to load up on pads when I see a sale on them.
It's sooo dependent on individual circumstances: terrain, weather, riding style, etc. Impossible to make a prediction. As brake pads are still very expensive right now (a holdover from the pandemic-induced supply chain issues), I recommend you just keep an eye on them and purchase spares when you see a decent price.
Koyote is online now  
Old 08-01-22, 04:43 PM
  #8  
NoWhammies
Senior Member
 
NoWhammies's Avatar
 
Join Date: Jul 2017
Location: Pacific Northwest
Posts: 1,993

Bikes: Argon 18 Gallium, BH G7, Rocky Mountain Instinct C70

Mentioned: 11 Post(s)
Tagged: 0 Thread(s)
Quoted: 800 Post(s)
Liked 512 Times in 306 Posts
Anywhere between 5,000 and 6,000km. But I ride up (and down) a LOT of hills.
NoWhammies is offline  
Likes For NoWhammies:
Old 08-01-22, 04:48 PM
  #9  
TakingMyTime
Senior Member
Thread Starter
 
Join Date: Aug 2012
Location: Los Alamitos, Calif.
Posts: 2,478

Bikes: Trek 7.4 FX

Mentioned: 4 Post(s)
Tagged: 0 Thread(s)
Quoted: 1026 Post(s)
Liked 912 Times in 535 Posts
Originally Posted by Koyote
. As brake pads are still very expensive right now (a holdover from the pandemic-induced supply chain issues), I recommend you just keep an eye on them and purchase spares when you see a decent price.
That's kind of my dilemma right now. I just purchased a 12 speed Di2 bike and would like to slowly put together a drawer of spares i.e. chain, cassette, brake pads etc. I guess the hard part is trying to decide if a 12 speed cassette is going to be $111 like it is now or drop to $80 a year from now.

BTW... thanks for all the replies

Last edited by TakingMyTime; 08-01-22 at 04:48 PM. Reason: spelling
TakingMyTime is online now  
Old 08-01-22, 05:02 PM
  #10  
Polaris OBark
ignominious poltroon
 
Polaris OBark's Avatar
 
Join Date: Jan 2022
Posts: 3,923
Mentioned: 3 Post(s)
Tagged: 0 Thread(s)
Quoted: 2184 Post(s)
Liked 3,336 Times in 1,741 Posts
Polaris OBark is offline  
Likes For Polaris OBark:
Old 08-01-22, 07:59 PM
  #11  
jaxgtr
Senior Member
 
jaxgtr's Avatar
 
Join Date: Jul 2006
Location: Jacksonville, FL
Posts: 6,830

Bikes: Trek Domane SLR 7 AXS, Trek CheckPoint SL7, Trek Emonda ALR, Trek FX 5 Sport

Mentioned: 2 Post(s)
Tagged: 0 Thread(s)
Quoted: 751 Post(s)
Liked 1,666 Times in 980 Posts
4k+ at the moment on the original set. However, I do not have hills or mountains so, I expect to have 6K at a minimum
__________________
Brian | 2023 Trek Domane SLR 7 AXS | 2023 Trek CheckPoint SL 7 AXS | 2016 Trek Emonda ALR | 2022 Trek FX Sport 5
Originally Posted by AEO
you should learn to embrace change, and mock it's failings every step of the way.



jaxgtr is offline  
Old 08-02-22, 01:12 PM
  #12  
sshakari
Senior Member
 
sshakari's Avatar
 
Join Date: Jul 2005
Location: Tarzana, CA
Posts: 700

Bikes: Canyon Endurace, Merckx liege 75, Cinelli Vigorelli

Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 167 Post(s)
Liked 114 Times in 61 Posts
Just changed my brakes at 3.5k miles. Im also curious about how often people change the disk.
__________________
If you have a steady supply of something, you can afford it and it's not interfering with your life, there's nothing wrong with being addicted. - Roland Griffiths
sshakari is offline  
Old 08-02-22, 04:23 PM
  #13  
vespasianus
Senior Member
 
Join Date: Jul 2019
Location: In the south but from North
Posts: 685

Bikes: Turner 5-Spot Burner converted; IBIS Ripley, Specialized Crave, Tommasini Sintesi, Cinelli Superstar, Tommasini X-Fire Gravel

Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 395 Post(s)
Liked 374 Times in 209 Posts
Originally Posted by sshakari
Just changed my brakes at 3.5k miles. Im also curious about how often people change the disk.
I have an MTB with 10+ years of use and I have never changed the rotor. They can last forever.
vespasianus is online now  
Old 08-02-22, 04:44 PM
  #14  
Drago1010
Newbie
 
Join Date: Aug 2009
Location: Chicago, IL
Posts: 74

Bikes: Spec Roubaix SL4 Comp Disc.Cannondale Synapse, Fuji Tread 1.0, Marin Larkspur

Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 5 Post(s)
Liked 8 Times in 7 Posts
I have a 2015 road bike with probably 22000+ miles and just changed rotors this year at 1.4mm thickness, (1.5 mm spec min on rotor), I've propbably changed my front brake pad 3-4 times and my rear twice (I mostly use my front brake). I replace the pads by measurement (<1mm).
Drago1010 is offline  
Old 08-02-22, 04:47 PM
  #15  
WhyFi
Senior Member
 
WhyFi's Avatar
 
Join Date: Jan 2010
Location: TC, MN
Posts: 39,505

Bikes: R3 Disc, Haanjo

Mentioned: 353 Post(s)
Tagged: 1 Thread(s)
Quoted: 20791 Post(s)
Liked 9,436 Times in 4,663 Posts
Originally Posted by sshakari
Just changed my brakes at 3.5k miles. Im also curious about how often people change the disk.
I swapped one recently, a Shimano IceTech, Ultegra-level, 160mm jobber. I think that it had about 16,000 - 18,000 miles on it. This was, again, on the rear, which I tend to wear out more quickly than the front.
WhyFi is offline  
Old 08-02-22, 04:53 PM
  #16  
Koyote
Senior Member
 
Join Date: Sep 2017
Posts: 7,763
Mentioned: 37 Post(s)
Tagged: 0 Thread(s)
Quoted: 6881 Post(s)
Liked 10,869 Times in 4,634 Posts
Originally Posted by WhyFi
I swapped one recently, a Shimano IceTech, Ultegra-level, 160mm jobber. I think that it had about 16,000 - 18,000 miles on it. This was, again, on the rear, which I tend to wear out more quickly than the front.
Just goes to show the individual nature of it. I just replaced the front rotor on my gravel bike after 10k miles -- it was measuring less than 1.5mm thick with my caliper. Rear rotor is still at 1.6mm or so.
Koyote is online now  
Old 08-02-22, 04:54 PM
  #17  
Polaris OBark
ignominious poltroon
 
Polaris OBark's Avatar
 
Join Date: Jan 2022
Posts: 3,923
Mentioned: 3 Post(s)
Tagged: 0 Thread(s)
Quoted: 2184 Post(s)
Liked 3,336 Times in 1,741 Posts
I tend to go through rotors about once a year or so. I find the center-lock ones (which also have better cooling fins) seem to last longer.
Polaris OBark is offline  
Old 08-02-22, 05:43 PM
  #18  
sshakari
Senior Member
 
sshakari's Avatar
 
Join Date: Jul 2005
Location: Tarzana, CA
Posts: 700

Bikes: Canyon Endurace, Merckx liege 75, Cinelli Vigorelli

Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 167 Post(s)
Liked 114 Times in 61 Posts
Originally Posted by WhyFi
I swapped one recently, a Shimano IceTech, Ultegra-level, 160mm jobber. I think that it had about 16,000 - 18,000 miles on it. This was, again, on the rear, which I tend to wear out more quickly than the front.
wonder if you sand them down every so often? Just replaced both front and back as my rear had deep grooves in it from lack of care and worn-out back brakes.
Also, changed the front caliper as I was too frustrated with its performance of it and sticky pistons - no matter what I did. Was very frustrated with it and decided to just get a new one. Only realized that there is a rebuild kit for them and its quite easy to rebuild them. Truth be told, I also snapped a mounting bolt on it with my f***up torque wrench. Lots of lessons were learned in this work.
__________________
If you have a steady supply of something, you can afford it and it's not interfering with your life, there's nothing wrong with being addicted. - Roland Griffiths
sshakari is offline  
Old 08-02-22, 06:03 PM
  #19  
WhyFi
Senior Member
 
WhyFi's Avatar
 
Join Date: Jan 2010
Location: TC, MN
Posts: 39,505

Bikes: R3 Disc, Haanjo

Mentioned: 353 Post(s)
Tagged: 1 Thread(s)
Quoted: 20791 Post(s)
Liked 9,436 Times in 4,663 Posts
Originally Posted by Koyote
Just goes to show the individual nature of it. I just replaced the front rotor on my gravel bike after 10k miles -- it was measuring less than 1.5mm thick with my caliper. Rear rotor is still at 1.6mm or so.
Definitely. Braking habits, topography, community - lots of reasons for mileage to vary.

Originally Posted by sshakari
wonder if you sand them down every so often? Just replaced both front and back as my rear had deep grooves in it from lack of care and worn-out back brakes.
Also, changed the front caliper as I was too frustrated with its performance of it and sticky pistons - no matter what I did. Was very frustrated with it and decided to just get a new one. Only realized that there is a rebuild kit for them and its quite easy to rebuild them. Truth be told, I also snapped a mounting bolt on it with my f***up torque wrench. Lots of lessons were learned in this work.
I've never sanded down my rotors, though I've sanded down my pads once in a while, when they've been contaminated.
WhyFi is offline  
Likes For WhyFi:
Old 08-03-22, 09:33 AM
  #20  
Bob Ross
your god hates me
 
Bob Ross's Avatar
 
Join Date: Apr 2006
Posts: 4,579

Bikes: 2016 Richard Sachs, 2010 Carl Strong, 2006 Cannondale Synapse

Mentioned: 10 Post(s)
Tagged: 0 Thread(s)
Quoted: 1232 Post(s)
Liked 1,241 Times in 689 Posts
Originally Posted by Iride01
Wide range of values you are seeing are likely because some people are in areas with high demands for braking and others are in areas where you can just let the hammer down for the entire ride.
I also suspect some ride the brakes more on turns and others are more confident of their line and speed through the turn.
One of the most amusing posts I ever saw on my cycle club's message board came from a member who -- in all seriousness -- wrote "I prefer to ride solo rather than in groups because that way I get more life out of my brake pads."
Bob Ross is online now  
Old 08-03-22, 09:39 AM
  #21  
Polaris OBark
ignominious poltroon
 
Polaris OBark's Avatar
 
Join Date: Jan 2022
Posts: 3,923
Mentioned: 3 Post(s)
Tagged: 0 Thread(s)
Quoted: 2184 Post(s)
Liked 3,336 Times in 1,741 Posts
Originally Posted by WhyFi
I've never sanded down my rotors, though I've sanded down my pads once in a while, when they've been contaminated.
I tried it. I had a new rotor damaged by a pad that was beyond end-of-life (kid was on the bike, we were in an active wildfire zone, and no time and nowhere to stop and deal with the problem). I wanted to see if I could salvage it, as it looked a bit pitted but otherwise ok. It only made it worse.
Polaris OBark is offline  
Old 08-03-22, 04:13 PM
  #22  
sean.hwy
Senior Member
 
sean.hwy's Avatar
 
Join Date: Jan 2020
Location: San Jose
Posts: 1,022

Bikes: Blur / Ibis Hakka MX / team machince alr2 / topstone 1

Mentioned: 1 Post(s)
Tagged: 0 Thread(s)
Quoted: 424 Post(s)
Liked 272 Times in 200 Posts
Still good? Having trouble finding replacement GRX brake pads for the gravel bike. I am so used to auto brake pads. These bike pads look done to me but they are not to what I assume is the warning track.




sean.hwy is offline  
Old 08-03-22, 05:07 PM
  #23  
WhyFi
Senior Member
 
WhyFi's Avatar
 
Join Date: Jan 2010
Location: TC, MN
Posts: 39,505

Bikes: R3 Disc, Haanjo

Mentioned: 353 Post(s)
Tagged: 1 Thread(s)
Quoted: 20791 Post(s)
Liked 9,436 Times in 4,663 Posts
Originally Posted by sean.hwy
Still good? Having trouble finding replacement GRX brake pads for the gravel bike. I am so used to auto brake pads. These bike pads look done to me but they are not to what I assume is the warning track.
In general, if the spring clip isn't rubbing the rotor, I'm fine with it, but Shimano does have a min thickness spec out there - should be easy enough to find.

Shimano pads were nowhere to be found (other than price-gougers) earlier in the year and I wouldn't be surprised if that was still the case. I was in dire need and ended up going with some compatible pads from Kool Stop.
WhyFi is offline  
Likes For WhyFi:
Old 08-03-22, 05:08 PM
  #24  
sean.hwy
Senior Member
 
sean.hwy's Avatar
 
Join Date: Jan 2020
Location: San Jose
Posts: 1,022

Bikes: Blur / Ibis Hakka MX / team machince alr2 / topstone 1

Mentioned: 1 Post(s)
Tagged: 0 Thread(s)
Quoted: 424 Post(s)
Liked 272 Times in 200 Posts
Originally Posted by WhyFi
In general, if the spring clip isn't rubbing the rotor, I'm fine with it, but Shimano does have a min thickness spec out there - should be easy enough to find.

Shimano pads were nowhere to be found (other than price-gougers) earlier in the year and I wouldn't be surprised if that was still the case. I was in dire need and ended up going with some compatible pads from Kool Stop.
thanks
sean.hwy is offline  
Old 08-03-22, 06:10 PM
  #25  
bampilot06
Senior Member
 
Join Date: Dec 2019
Location: 757
Posts: 11,030

Bikes: Madone, Emonda, 5500, Ritchey Breakaway

Mentioned: 2 Post(s)
Tagged: 0 Thread(s)
Quoted: 10046 Post(s)
Liked 5,035 Times in 2,148 Posts
I’m at 10,000 miles currently on the original set of pads.
bampilot06 is offline  

Thread Tools
Search this Thread

Contact Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service -

Copyright © 2024 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.