Soldering wiring guides on steel frame?
#1
Passista
Thread Starter
Join Date: Jul 2005
Posts: 7,596
Bikes: 1998 Pinarello Asolo, 1992 KHS Montaña pro, 1980 Raleigh DL-1, IGH Hybrid, IGH Utility
Mentioned: 5 Post(s)
Tagged: 0 Thread(s)
Quoted: 866 Post(s)
Liked 720 Times
in
395 Posts
Soldering wiring guides on steel frame?
After 11 years and 50,000kms I'm going to strip and brush-paint (thanks randyjawa!) my steel hybrid frame. I use dynamo lighting with the wires fastened with zip ties. Thought to make guides from thin sheet metal and tin soldering them to the bare frame. Never seen it done before, what do you think of it?
#2
Sr Member on Sr bikes
On a steel frame I think I’d consider internal routing before soldering tubing onto the frame.
Dan
Dan
#3
Senior Member
Join Date: Feb 2012
Location: Rochester, NY
Posts: 18,056
Bikes: Stewart S&S coupled sport tourer, Stewart Sunday light, Stewart Commuting, Stewart Touring, Co Motion Tandem, Stewart 3-Spd, Stewart Track, Fuji Finest, Mongoose Tomac ATB, GT Bravado ATB, JCP Folder, Stewart 650B ATB
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 4195 Post(s)
Liked 3,837 Times
in
2,295 Posts
Since the wire guides/clips will see very little tension on them and should one come off the results is not likely to be a immediate safety situation I sat YES, simple plumbing solder should be fine. Consider looking at the K&S model metal tubing offers before making your own clips. They offer cool brass tubes in small diameters and thin walls that are easily manipulated, filed, sanded. Andy
__________________
AndrewRStewart
AndrewRStewart
#4
Senior Member
Join Date: May 2010
Location: Bastrop Texas
Posts: 4,467
Bikes: Univega, Peu P6, Peu PR-10, Ted Williams, Peu UO-8, Peu UO-18 Mixte, Peu Dolomites
Mentioned: 13 Post(s)
Tagged: 0 Thread(s)
Quoted: 957 Post(s)
Liked 1,619 Times
in
1,039 Posts
No problem. I have silver soldered/brazed many Shifter and Cable Bosses to my steel frames. I use a little Harbor Freight touch and plumbers silver solder with regular copper pipe flux. It's no biggy but you should do a few test runs on similar tubing. I also make sure the frame and bosses are clean and sanded to expose raw metal.
https://framebuildersupply.com/collections/braze-ons
https://framebuildersupply.com/collections/braze-ons
__________________
No matter where you're at... There you are... Δf:=f(1/2)-f(-1/2)
No matter where you're at... There you are... Δf:=f(1/2)-f(-1/2)
#5
Senior Member
Join Date: Sep 2010
Location: Roswell, GA
Posts: 8,319
Bikes: '93 Trek 750, '92 Schwinn Crisscross, '93 Mongoose Alta
Mentioned: 30 Post(s)
Tagged: 0 Thread(s)
Quoted: 1438 Post(s)
Liked 1,092 Times
in
723 Posts
No problem. I have silver soldered/brazed many Shifter and Cable Bosses to my steel frames. I use a little Harbor Freight touch and plumbers silver solder with regular copper pipe flux. It's no biggy but you should do a few test runs on similar tubing. I also make sure the frame and bosses are clean and sanded to expose raw metal.
https://framebuildersupply.com/collections/braze-ons
https://framebuildersupply.com/collections/braze-ons
Likes For dsbrantjr:
#6
Senior Member
Join Date: Feb 2007
Posts: 1,422
Mentioned: 5 Post(s)
Tagged: 0 Thread(s)
Quoted: 619 Post(s)
Likes: 0
Liked 389 Times
in
272 Posts
I used glue on hydraulic cable guides on the frame and rear rack. I cleaned the paint with alcohol stuck them on then to make sure they stayed on I used a little Shoe Goo.
#8
Passista
Thread Starter
Join Date: Jul 2005
Posts: 7,596
Bikes: 1998 Pinarello Asolo, 1992 KHS Montaña pro, 1980 Raleigh DL-1, IGH Hybrid, IGH Utility
Mentioned: 5 Post(s)
Tagged: 0 Thread(s)
Quoted: 866 Post(s)
Liked 720 Times
in
395 Posts
Soldered 3 guides, all went OK.
Before finishing:
Finished:
This guides are 6mm diameter and they will be used for my Nexus cable & dynamo wiring.
Before finishing:
Finished:
This guides are 6mm diameter and they will be used for my Nexus cable & dynamo wiring.
#9
Senior Member
#11
Senior Member
#12
Senior Member
Join Date: Sep 2020
Location: Eastern Poland
Posts: 743
Bikes: Romet Jubilat x 4, Wigry x 1, Turing x 1
Mentioned: 3 Post(s)
Tagged: 0 Thread(s)
Quoted: 194 Post(s)
Liked 204 Times
in
151 Posts
Having seen this I am planning on doing something similar on some of my bikes
As I also use dynamos but dislike having wires wrapped around the frame I sometimes run the wires through brake housing and then clip that to the frame.
IGH and front-to-rear dynamo housings
As I also use dynamos but dislike having wires wrapped around the frame I sometimes run the wires through brake housing and then clip that to the frame.
IGH and front-to-rear dynamo housings