Huret Allvit rear derailleur
#1
Full Member
Thread Starter
Join Date: Jul 2010
Location: Worcester, MA, USA
Posts: 411
Bikes: Dawes Lightning DLX, 1988 Klein Performance, 1991 Peugeot Safari, 1985 Raleigh Alyeska, Carrera Phantom, 1973 Raleigh Record
Mentioned: 1 Post(s)
Tagged: 0 Thread(s)
Quoted: 282 Post(s)
Liked 129 Times
in
92 Posts
Huret Allvit rear derailleur
I'm trying to disassemble a Huret Allvit RD just to clean it up, re-lube, and re-assemble. I'm stuck on the jockey wheels. I've got one free of the cage, but I'm not sure how to get to the ball bearings. The other one, I can't get the nuts loose to remove it from the cage. The nuts are circular with two flats, so a socket won't fit; I think my only option is an open-end wrench. The nuts are low-profile, too, so it's easy to slip when you apply torque to the wrench. Any tips?
#2
Senior Member
Join Date: Dec 2020
Location: Wake Forest, NC
Posts: 5,783
Bikes: 1989 Cinelli Supercorsa
Mentioned: 11 Post(s)
Tagged: 0 Thread(s)
Quoted: 3504 Post(s)
Liked 2,922 Times
in
1,774 Posts
Make sure you have the right-sized wrench?
#3
Senior Member
Join Date: Feb 2012
Location: Rochester, NY
Posts: 18,071
Bikes: Stewart S&S coupled sport tourer, Stewart Sunday light, Stewart Commuting, Stewart Touring, Co Motion Tandem, Stewart 3-Spd, Stewart Track, Fuji Finest, Mongoose Tomac ATB, GT Bravado ATB, JCP Folder, Stewart 650B ATB
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 4199 Post(s)
Liked 3,851 Times
in
2,301 Posts
A cone wrench (IIRC 13mm) will fit these pulley cones. Like some low cost front hubs, the cone/bearing preload is held by the cage bolts (axle nuts in the hub example). So some trial and try again is the usual process to find both the best cone/pulley spin after pulley bolts are tightened.
For a budding wrench these Allvit ders are a great training ground for basic assembly skills. How to set bolts and lock nuts to allow for freely moving pivots but no slop. How to work with springs that fight your fingers. And the older bike need, how to adjust cup and cone bearings. Andy
For a budding wrench these Allvit ders are a great training ground for basic assembly skills. How to set bolts and lock nuts to allow for freely moving pivots but no slop. How to work with springs that fight your fingers. And the older bike need, how to adjust cup and cone bearings. Andy
__________________
AndrewRStewart
AndrewRStewart
Likes For Andrew R Stewart:
#5
Full Member
Thread Starter
Join Date: Jul 2010
Location: Worcester, MA, USA
Posts: 411
Bikes: Dawes Lightning DLX, 1988 Klein Performance, 1991 Peugeot Safari, 1985 Raleigh Alyeska, Carrera Phantom, 1973 Raleigh Record
Mentioned: 1 Post(s)
Tagged: 0 Thread(s)
Quoted: 282 Post(s)
Liked 129 Times
in
92 Posts
A cone wrench (IIRC 13mm) will fit these pulley cones. Like some low cost front hubs, the cone/bearing preload is held by the cage bolts (axle nuts in the hub example). So some trial and try again is the usual process to find both the best cone/pulley spin after pulley bolts are tightened.
For a budding wrench these Allvit ders are a great training ground for basic assembly skills. How to set bolts and lock nuts to allow for freely moving pivots but no slop. How to work with springs that fight your fingers. And the older bike need, how to adjust cup and cone bearings. Andy
For a budding wrench these Allvit ders are a great training ground for basic assembly skills. How to set bolts and lock nuts to allow for freely moving pivots but no slop. How to work with springs that fight your fingers. And the older bike need, how to adjust cup and cone bearings. Andy