Replacing Helmet Buckle Male Clasp
#1
Full Member
Thread Starter
Join Date: Sep 2015
Location: Maryland
Posts: 347
Bikes: Nashbar Race SIS, Spalding Road Step Through Single Speed, Kent Road Single Speed, 630 Cruiser, Fuji Odessa mountain bike
Mentioned: 3 Post(s)
Tagged: 0 Thread(s)
Quoted: 109 Post(s)
Likes: 0
Liked 1 Time
in
1 Post
Replacing Helmet Buckle Male Clasp
I have a Giro Syntax MIPS. The male part of the side-release buckle fell off, not to be found. I've been measuring and not sure if a replacement should be 3/4" or 13/16". There are a lot of choices, and not sure about whether the replacement should be described as "curved." And, looking for a wiki how type tutorial on how to thread the buckle and to help me decide whether or not it should be sewed into position.
#2
Callipygian Connoisseur
Join Date: Nov 2008
Posts: 1,373
Mentioned: 13 Post(s)
Tagged: 0 Thread(s)
Quoted: 564 Post(s)
Liked 350 Times
in
190 Posts
Buy a whole new buckle (male/female) and take your helmet and new buckle to a shoe or luggage repair shop.
Edited to add: A cheap and easy way to find a plastic side clip buckle is in a department store’s dog collar section.
Edited to add: A cheap and easy way to find a plastic side clip buckle is in a department store’s dog collar section.
Last edited by Kedosto; 05-07-22 at 09:11 AM.
#3
Senior Member
Join Date: Jun 2005
Location: Kentucky
Posts: 2,599
Bikes: 06 Lemond Reno, 98 GT Timberline mtn.bike
Mentioned: 8 Post(s)
Tagged: 0 Thread(s)
Quoted: 427 Post(s)
Liked 699 Times
in
436 Posts
Tip-by entering your thread title, followed by Bike Forums, on Google, it will bring up any old responses if the topic has been asked previously. example: Anybody know where to get helmet strap clips? - Bike Forums
#4
Pennylane Splitter
Join Date: Sep 2012
Location: Orange County, California
Posts: 1,879
Bikes: Yes
Mentioned: 14 Post(s)
Tagged: 0 Thread(s)
Quoted: 1796 Post(s)
Liked 1,439 Times
in
989 Posts
Try a fabric or crafts store. There's a Joann's Fabrics & Crafts store down the street from me that has a whole bunch of different sizes of plastic buckles. Michaels or Hobby Lobby might have them, too.
Likes For skidder:
#5
Senior Member
Join Date: Jul 2008
Location: 25 miles northwest of Boston
Posts: 29,549
Bikes: Bottecchia Sprint, GT Timberline 29r, Marin Muirwoods 29er, Trek FX Alpha 7.0
Mentioned: 112 Post(s)
Tagged: 0 Thread(s)
Quoted: 5224 Post(s)
Liked 3,581 Times
in
2,342 Posts
fwiw - lately, after adjusting my helmet for whatever headwear I have underneath, I wrap a a small piece of tape around the loose end. this keeps the adjustment & prevents the loss of that male clip. I had 1 helmet, whose strap, was particularly vulnerable for this. the little rubber o-ring intended for the purpose, was inadequate
Likes For rumrunn6:
#6
Senior Member
Join Date: Dec 2010
Location: northern Deep South
Posts: 8,901
Bikes: Fuji Touring, Novara Randonee
Mentioned: 36 Post(s)
Tagged: 0 Thread(s)
Quoted: 2604 Post(s)
Liked 1,928 Times
in
1,210 Posts
When something like a hard plastic buckle breaks (or disappears) I often take that as a signal that it's time to replace the helmet.
#7
I'm good to go!
Join Date: Jul 2017
Location: Mississippi
Posts: 14,985
Bikes: Tarmac Disc Comp Di2 - 2020
Mentioned: 51 Post(s)
Tagged: 0 Thread(s)
Quoted: 6193 Post(s)
Liked 4,808 Times
in
3,316 Posts
Fire off an email to Giro. While many times such things are fruitless, I still find that occasionally it gets results. Maybe they'll put one in the mail to you.
#8
Grupetto Bob
Join Date: Sep 2020
Location: Seattle-ish
Posts: 6,211
Bikes: Bikey McBike Face
Mentioned: 2 Post(s)
Tagged: 0 Thread(s)
Quoted: 2579 Post(s)
Liked 5,636 Times
in
2,920 Posts
__________________
Road 🚴🏾♂️ & Mountain 🚵🏾♂️
Road 🚴🏾♂️ & Mountain 🚵🏾♂️
Likes For rsbob:
#9
Senior Member
Join Date: May 2010
Location: Bastrop Texas
Posts: 4,476
Bikes: Univega, Peu P6, Peu PR-10, Ted Williams, Peu UO-8, Peu UO-18 Mixte, Peu Dolomites
Mentioned: 13 Post(s)
Tagged: 0 Thread(s)
Quoted: 964 Post(s)
Liked 1,628 Times
in
1,044 Posts
Ya can print one out... I would use ABS instead of PLA... Still buying one pre-manufactured would be best as your printed version would be unproven...
https://www.thingiverse.com/thing:1416
https://www.thingiverse.com/thing:1416
__________________
No matter where you're at... There you are... Δf:=f(1/2)-f(-1/2)
No matter where you're at... There you are... Δf:=f(1/2)-f(-1/2)
#10
Senior Member
Join Date: Oct 2014
Location: Portland, OR
Posts: 12,903
Bikes: (2) ti TiCycles, 2007 w/ triple and 2011 fixed, 1979 Peter Mooney, ~1983 Trek 420 now fixed and ~1973 Raleigh Carlton Competition gravel grinder
Mentioned: 129 Post(s)
Tagged: 0 Thread(s)
Quoted: 4805 Post(s)
Liked 3,927 Times
in
2,553 Posts
If you have an REI, Dick's Sporting Goods or other outdoor store nearby, go tho their customer service. Backpacks use the same or very close clips.
I keep a Speedy Stitcher on hand for all sorts of useful stuff. (An awl you load with waxed nylon or polyester thread.) One stitch with that keeps helmet strap ends in place.
The Speedy Stitcher is an incredibly useful tool. I've repaired cycling shoes, panniers, backpacks, tents, sails and created all sorts of useful things with it. Most of my bike tool bags have velcro or straps Speedy Stitched on. My avatar bike has a 12 tooth cog hanging from a velcro strap and the Pedros Trixie hub wrench and lockring spanner strapped in place underneath.
I keep a Speedy Stitcher on hand for all sorts of useful stuff. (An awl you load with waxed nylon or polyester thread.) One stitch with that keeps helmet strap ends in place.
The Speedy Stitcher is an incredibly useful tool. I've repaired cycling shoes, panniers, backpacks, tents, sails and created all sorts of useful things with it. Most of my bike tool bags have velcro or straps Speedy Stitched on. My avatar bike has a 12 tooth cog hanging from a velcro strap and the Pedros Trixie hub wrench and lockring spanner strapped in place underneath.
Likes For 79pmooney:
#11
Senior Member
Join Date: Jul 2002
Location: Sacramento, California, USA
Posts: 40,865
Bikes: Specialized Tarmac, Canyon Exceed, Specialized Transition, Ellsworth Roots, Ridley Excalibur
Mentioned: 68 Post(s)
Tagged: 0 Thread(s)
Quoted: 2952 Post(s)
Liked 3,106 Times
in
1,417 Posts
You have options:
1) email Giro directly and ask
2) go to the bike shop and ask
3) go to REI and buy new male and female parts that fit the strap
1) email Giro directly and ask
2) go to the bike shop and ask
3) go to REI and buy new male and female parts that fit the strap
Likes For caloso:
#12
OM boy
Join Date: Jul 2005
Location: Goleta CA
Posts: 4,365
Bikes: a bunch
Mentioned: 11 Post(s)
Tagged: 0 Thread(s)
Quoted: 514 Post(s)
Liked 642 Times
in
437 Posts
fwiw - lately, after adjusting my helmet for whatever headwear I have underneath, I wrap a a small piece of tape around the loose end. this keeps the adjustment & prevents the loss of that male clip. I had 1 helmet, whose strap, was particularly vulnerable for this. the little rubber o-ring intended for the purpose, was inadequate
one of the many uses for old tubes...
OR
you can also use those black wire wraps that are used for holding cords on electronic devices wrapped.
Ride On
Yuri
Likes For cyclezen: