Go Back  Bike Forums > Bike Forums > Bicycle Mechanics
Reload this Page >

D.I.Y Dish tool

Notices
Bicycle Mechanics Broken bottom bracket? Tacoed wheel? If you're having problems with your bicycle, or just need help fixing a flat, drop in here for the latest on bicycle mechanics & bicycle maintenance.

D.I.Y Dish tool

Old 07-02-21, 10:31 AM
  #1  
hevysrf
Junior Member
Thread Starter
 
Join Date: Sep 2004
Posts: 130
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 79 Post(s)
Liked 66 Times in 31 Posts
D.I.Y Dish tool

I don't have a lot of wheel building under my belt, and don't plan on being high volume, so the Minoura FT-1 seemed like a good value. It's a little shaky but usable with care.

The dish gage that came with it is another story, I just couldn't get the correct angle and depth.

Might just be me or the wheel I'm using it on, so I came up with an alternative.




















hevysrf is offline  
Likes For hevysrf:
Old 07-02-21, 10:54 AM
  #2  
Nessism
Senior Member
 
Nessism's Avatar
 
Join Date: Jun 2004
Location: Torrance, CA
Posts: 3,059

Bikes: Homebuilt steel

Mentioned: 18 Post(s)
Tagged: 0 Thread(s)
Quoted: 2182 Post(s)
Liked 421 Times in 334 Posts
No disrespect but I would rather use the truing stand and flip flop the wheel until you get good understanding of the built in side to side error.
Nessism is offline  
Old 07-02-21, 02:04 PM
  #3  
jccaclimber
Senior Member
 
Join Date: May 2005
Location: SFBay
Posts: 2,334

Bikes: n, I would like n+1

Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 127 Post(s)
Likes: 0
Liked 133 Times in 108 Posts
The stand works well enough, but the OP’s solution also looks perfectly serviceable, and probably used parts on hand.
jccaclimber is offline  
Likes For jccaclimber:
Old 07-03-21, 08:30 AM
  #4  
Pop N Wood
Senior Member
 
Join Date: Jun 2020
Location: Maryland
Posts: 1,379

Bikes: 1982 Bianchi Sport SX, Rayleigh Tamland 1, Rans V-Rex recumbent, Fuji MTB, 80's Cannondale MTB with BBSHD ebike motor

Mentioned: 1 Post(s)
Tagged: 0 Thread(s)
Quoted: 667 Post(s)
Liked 529 Times in 355 Posts
Pretty easy to put the wheel on the bike and measure the distance from the stays.

I've purposely off centered rear wheels with disc brakes to get a more equal spoke angle.
Pop N Wood is offline  
Old 07-04-21, 09:13 AM
  #5  
easyupbug 
Senior Member
 
Join Date: Jan 2013
Posts: 2,652

Bikes: too many sparkly Italians, some sweet Americans and a couple interesting Japanese

Mentioned: 9 Post(s)
Tagged: 0 Thread(s)
Quoted: 560 Post(s)
Liked 546 Times in 396 Posts
If you build more than a few wheels the handy convenience of Roger's design is hard to beat: https://www.wheelpro.co.uk/support/dishing-tool.php
His book on wheel building is outstanding.
easyupbug is offline  
Likes For easyupbug:
Old 07-04-21, 09:39 AM
  #6  
hevysrf
Junior Member
Thread Starter
 
Join Date: Sep 2004
Posts: 130
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 79 Post(s)
Liked 66 Times in 31 Posts
Originally Posted by easyupbug
If you build more than a few wheels the handy convenience of Roger's design is hard to beat: https://www.wheelpro.co.uk/support/dishing-tool.php
His book on wheel building is outstanding.

Wow, that link sent me down a rabbit hole, looks like a Wheel Fanatyk Tensiometer is on my wish list.
hevysrf is offline  
Likes For hevysrf:
Old 07-04-21, 01:33 PM
  #7  
andrewclaus
Senior Member
 
Join Date: Feb 2012
Location: Golden, CO and Tucson, AZ
Posts: 2,822

Bikes: 2016 Fuji Tread, 1983 Trek 520

Mentioned: 13 Post(s)
Tagged: 0 Thread(s)
Quoted: 669 Post(s)
Liked 725 Times in 422 Posts
Your Unistrut is much better than the old bed frame I used.

You can also use three stacks of books.
andrewclaus is offline  
Old 07-06-21, 05:08 PM
  #8  
SBinNYC
Senior Member
 
Join Date: Nov 2009
Posts: 555
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 31 Post(s)
Likes: 0
Liked 10 Times in 8 Posts
Francis Bollag suggested this DIY dishing gauge a while back. It consists of a flat table, 3 or 6 tuna fish cans, and a stack of pennies. Support the wheel by the rim at 3 points by the tuna fish cans. Two cans should be sufficient so that the axle is above the table surface. Use the stack of pennies as your measuring gauge to the locknut. Flip the wheel. Adjust the dish so that you are a penny width between the two sides.
SBinNYC is offline  

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


Thread Tools
Search this Thread

Contact Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service -

Copyright © 2024 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.