Go Back  Bike Forums > Bike Forums > Classic & Vintage
Reload this Page >

The Masi's dropout hanger is askew

Notices
Classic & Vintage This forum is to discuss the many aspects of classic and vintage bicycles, including musclebikes, lightweights, middleweights, hi-wheelers, bone-shakers, safety bikes and much more.

The Masi's dropout hanger is askew

Old 09-18-19, 12:39 PM
  #1  
tiger1964 
Senior Member
Thread Starter
 
tiger1964's Avatar
 
Join Date: Apr 2011
Location: Maryland, USA
Posts: 2,414

Bikes: Drysdale/Gitane/Zeus/Masi/Falcon/Palo Alto/Raleigh/Legnano

Mentioned: 34 Post(s)
Tagged: 0 Thread(s)
Quoted: 966 Post(s)
Liked 613 Times in 393 Posts
The Masi's dropout hanger is askew

Overall, been enjoying the Masi Gran Corsa in recent weeks, since moving most of the parts over from the Palo Alto. But today I went further afield than my local rail-trail for the first time. Nice ride, but I have had some nagging dissatisfaction with shifting, and "trim noise" from the RD. I was mentally blaming the freewheel that came with wider-hubbed (126mm) wheels.


So, I was cleaning the bike on a stand on the patio, and took a closer look. The RD's cage is clearly out of plane by a few degrees, bottom pulley closer to the centerline of the bike than the upper pulley. Uh - oh...


As part of a process of elimination, I figured maybe it's the old Nuovo Record (Pat74) RD, had it's day. So I swapped in one that I had been given with zero miles on it (Pat71). No change. What's left? The hanger. I figure the hanger only needs to be out a millimeter or two for the "cumulative error", by the time you measure at the derailleur cage, to be noticeable.


So, I've been searching the forums for dropout topics. Most seem to be about traumatic damage, or misalignment of the dropouts where the wheels attach, especially after cold-setting the entire frame. Neither apply. I've read about "cold-setting" the hanger, as a first step before applying (!?!?!) heat. Not much about the actual technique. Input?


Right now, I am inclined to set the wheel-attachment portion (uh, is there a better term?) of the dropout in a vise to prevent (?) damaging that part, and then applying oomph to the hanger portion using my trusty 15" Crescent wrench (which, before I got better tools, was my way of removing fixed cups). Wrong? I suspect the hard part is knowing when "enough is enough" - small bites and repeatedly measuring by re-installing the wheel and RD. The good news is that, to my eye, I only need to adjust in the "roll axis" and not the "yaw axis" at the same time.


The frame arrived in lovely condition, I might conclude this is shipping damage on a scale so small it would have difficult to detect prior to assembly.
tiger1964 is offline  
Old 09-18-19, 12:43 PM
  #2  
unterhausen
Randomhead
 
Join Date: Aug 2008
Location: Happy Valley, Pennsylvania
Posts: 24,362
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 4 Post(s)
Liked 3,662 Times in 2,496 Posts
it's not unusual to have to bend those dropouts back occasionally. you need to find someone with a dropout hanger alignment tool. Park sells a serviceable one
unterhausen is offline  
Old 09-18-19, 12:44 PM
  #3  
tiger1964 
Senior Member
Thread Starter
 
tiger1964's Avatar
 
Join Date: Apr 2011
Location: Maryland, USA
Posts: 2,414

Bikes: Drysdale/Gitane/Zeus/Masi/Falcon/Palo Alto/Raleigh/Legnano

Mentioned: 34 Post(s)
Tagged: 0 Thread(s)
Quoted: 966 Post(s)
Liked 613 Times in 393 Posts
As I know someone will want to see a picture, here's one but I don't know if it adds anything useful (story about the photo being 90 degrees out):
__________________
Larry:1958 Drysdale, 1961 Gitane Gran Sport, 1974 Zeus track, 1988 Masi Gran Corsa, 1974 Falcon, 1980 Palo Alto, 1973 Raleigh Gran Sport, 1974 Legnano. Susan: 1976 Windsor Profesional.


tiger1964 is offline  
Old 09-18-19, 12:48 PM
  #4  
AeroGut
Senior Member
 
Join Date: Jun 2019
Posts: 679
Mentioned: 7 Post(s)
Tagged: 0 Thread(s)
Quoted: 254 Post(s)
Likes: 0
Liked 182 Times in 141 Posts
You might be able to get it right by eye, but it’s a lot easier with the right tool. Something like this: https://www.chainreactioncycles.com/.../rp-prod122319

if there’s a co-op nearby, they might have one you can use.

If you use a crescent wrench, I would do it with the wheel in the frame to hold the dropout in position.
AeroGut is offline  
Old 09-18-19, 12:49 PM
  #5  
due ruote 
Senior Member
 
due ruote's Avatar
 
Join Date: Dec 2006
Posts: 7,707
Mentioned: 30 Post(s)
Tagged: 0 Thread(s)
Quoted: 903 Post(s)
Liked 524 Times in 318 Posts
That’s a pretty common and easily fixed condition. You can buy a tool to align, or make your own like I did using a piece of square steel pipe from the hardware store, a scrap axle and some spacers.
To use, remove the RD, thread the short end of axle in the hanger, and snug things up so the pipe just turns freely. Then move it around the wheel and measure to the rim. Use the tool as a lever to gently bend the hanger as necessary until the hanger and rim are in parallel planes.

due ruote is offline  
Likes For due ruote:
Old 09-18-19, 12:52 PM
  #6  
tiger1964 
Senior Member
Thread Starter
 
tiger1964's Avatar
 
Join Date: Apr 2011
Location: Maryland, USA
Posts: 2,414

Bikes: Drysdale/Gitane/Zeus/Masi/Falcon/Palo Alto/Raleigh/Legnano

Mentioned: 34 Post(s)
Tagged: 0 Thread(s)
Quoted: 966 Post(s)
Liked 613 Times in 393 Posts
Originally Posted by unterhausen
it's not unusual to have to bend those dropouts back occasionally. you need to find someone with a dropout hanger alignment tool. Park sells a serviceable one
Originally Posted by AeroGut
You might be able to get it right by eye, but it’s a lot easier with the right tool. Something like this: https://www.chainreactioncycles.com/.../rp-prod122319
Thanks, I've bookmarked both. I trust Park tools, but the other one is about half the price. And this is a single-use situation (yeah, I say that, and...)
__________________
Larry:1958 Drysdale, 1961 Gitane Gran Sport, 1974 Zeus track, 1988 Masi Gran Corsa, 1974 Falcon, 1980 Palo Alto, 1973 Raleigh Gran Sport, 1974 Legnano. Susan: 1976 Windsor Profesional.


tiger1964 is offline  
Old 09-18-19, 01:04 PM
  #7  
brian3069
Senior Member
 
brian3069's Avatar
 
Join Date: Jun 2009
Posts: 1,905

Bikes: Raleigh Supercourse

Mentioned: 11 Post(s)
Tagged: 0 Thread(s)
Quoted: 218 Post(s)
Liked 167 Times in 101 Posts
Bummer, I'm sorry to see this. It's possible the frame was unknowingly shipped that way. Can you take it to a shop so the proper alignment tool can be used, I'd be happy to reimburse you for the cost.
brian3069 is online now  
Likes For brian3069:
Old 09-18-19, 01:22 PM
  #8  
markwesti
Senior Member
 
markwesti's Avatar
 
Join Date: Jul 2015
Location: Seal Beach Ca. On the right , next to Long Beach
Posts: 1,825

Bikes: 86' Centurion Ironman

Mentioned: 72 Post(s)
Tagged: 0 Thread(s)
Quoted: 628 Post(s)
Liked 314 Times in 175 Posts
50 bucks EBay , my LBS quoted 75 and I could have it back in 2 weeks .



IMG_0413 by mark westi, on Flickr
markwesti is offline  
Likes For markwesti:
Old 09-18-19, 02:22 PM
  #9  
noobinsf 
Senior Member
 
noobinsf's Avatar
 
Join Date: Sep 2005
Location: Oakland, CA
Posts: 3,291

Bikes: '82 Univega Competizione, '72 Motobecane Grand Record, '83 Mercian KOM Touring, '85 Univega Alpina Uno, '76 Eisentraut Limited

Mentioned: 57 Post(s)
Tagged: 0 Thread(s)
Quoted: 1088 Post(s)
Liked 1,204 Times in 700 Posts
Yeah, either use the tool or have a shop do it, especially because it looks like your seller will reimburse the cost. I did this last year on my Motobecane with a wrench and a level, and while I got it aligned, I nicked the thread and had to tap it to clean up the error. Not the worst consequence, but a dumb error that could have been worse, and, more importantly, avoided.
noobinsf is offline  
Old 09-18-19, 02:43 PM
  #10  
tiger1964 
Senior Member
Thread Starter
 
tiger1964's Avatar
 
Join Date: Apr 2011
Location: Maryland, USA
Posts: 2,414

Bikes: Drysdale/Gitane/Zeus/Masi/Falcon/Palo Alto/Raleigh/Legnano

Mentioned: 34 Post(s)
Tagged: 0 Thread(s)
Quoted: 966 Post(s)
Liked 613 Times in 393 Posts
As usual, good feedback here!

Originally Posted by brian3069
Bummer, I'm sorry to see this. It's possible the frame was unknowingly shipped that way. Can you take it to a shop so the proper alignment tool can be used, I'd be happy to reimburse you for the cost.
Generous of you Brian -- especially as it's not 100% certain how it happened. What do you say to splitting it (uh, the cost, not the dropout )?

Originally Posted by markwesti
50 bucks EBay , my LBS quoted 75 and I could have it back in 2 weeks.
Nice photo showing how the tool works.

Originally Posted by noobinsf
I did this last year on my Motobecane with a wrench and a level, and while I got it aligned, I nicked the thread and had to tap it to clean up the error.
Thanks for the warning; I was ready to break out Wrenchzilla. Still not sure I could not pull it off. I left a message with the LBS, let's see what they say about having the tool & time I'd be without the bike. Shoot, I've been riding it this way for, eh, 150 miles, thinking I had goofy freewheel.
__________________
Larry:1958 Drysdale, 1961 Gitane Gran Sport, 1974 Zeus track, 1988 Masi Gran Corsa, 1974 Falcon, 1980 Palo Alto, 1973 Raleigh Gran Sport, 1974 Legnano. Susan: 1976 Windsor Profesional.


tiger1964 is offline  
Old 09-18-19, 03:00 PM
  #11  
Salamandrine 
Senior Member
 
Join Date: Oct 2015
Location: Los Angeles
Posts: 6,287

Bikes: 78 Masi Criterium, 68 PX10, 2016 Mercian King of Mercia, Rivendell Clem Smith Jr

Mentioned: 120 Post(s)
Tagged: 0 Thread(s)
Quoted: 2317 Post(s)
Liked 597 Times in 430 Posts
Aligning the dropouts and derailleur hanger is always my first step in setting up a bike. I have the tools, which makes it easy, but it's pretty easy to improvise a hanger tool from a spare axle as shown above. The basic idea of doing this is that you rotate the tool around, and use the distance to the rear rim as a reference. If there is more space between the tool and the rim at the top then the bottom, push the arm in when it's at the top to even the distance. Same thing if there is more difference in the front vs rear when the arm is horizontal.

FYI you can get even lazier and simply use a wheel with the tire removed. Just compare the distance at various points around the rim. Even this will work 100x better than eyeballing it with a crescent wrench. IMO.

Pretty hilarious that shops are charging 75 bux nowadays. Shops I worked in did it automatically as part of yer basic $35 tuneup, or whatever it cost BITD. Took 43 seconds.
Salamandrine is offline  
Likes For Salamandrine:
Old 09-18-19, 03:42 PM
  #12  
brian3069
Senior Member
 
brian3069's Avatar
 
Join Date: Jun 2009
Posts: 1,905

Bikes: Raleigh Supercourse

Mentioned: 11 Post(s)
Tagged: 0 Thread(s)
Quoted: 218 Post(s)
Liked 167 Times in 101 Posts
Originally Posted by tiger1964

Generous of you Brian -- especially as it's not 100% certain how it happened. What do you say to splitting it (uh, the cost, not the dropout )?
Sounds fair, PM when you know the cost. Include your PP info.
brian3069 is online now  
Old 09-18-19, 05:11 PM
  #13  
Last ride 76 
1/2 as far in 2x the time
 
Last ride 76's Avatar
 
Join Date: Nov 2013
Location: Northern Bergen County, NJ
Posts: 1,935

Bikes: Yes, Please.

Mentioned: 13 Post(s)
Tagged: 0 Thread(s)
Quoted: 499 Post(s)
Liked 285 Times in 222 Posts
If you DIY make sure your wheel is square to the frame...
Last ride 76 is offline  
Old 09-18-19, 05:59 PM
  #14  
Doug Fattic 
framebuilder
 
Join Date: Dec 2009
Location: Niles, Michigan
Posts: 1,459
Mentioned: 50 Post(s)
Tagged: 0 Thread(s)
Quoted: 610 Post(s)
Liked 1,905 Times in 647 Posts
I'd call around to any nearby frame builders and see what they charge. While $75 for labor is not an unfair price compared to electricians and plumbers, it is a lot higher than I would charge if it is only the hanger out of adjustment. And your local frame builder is probably a lot more experienced using all frame alignment tools. While your frame is there he can probably do other checks like see if the dropouts are equal distant to the center of the frame or other alignment issues. Most customers assume their frames are in good alignment when a big percentage of them are not.

It is possible the LBS price includes a more complete alignment check and they are farming the job out to a frame builder anyway. That might be the reason for the 2 week wait. There is no point to having the hanger parallel to the wheel if the dropouts are not square to the plane of the frame (requiring H tools). And if the alignment of the main triangle is off then that compromises the alignment of the dropouts. This is why a DIY job may not get everything right.

FYI dropout alignment tools are called "H tools" because that is how they were identified in old Campy catalogs. Their tools started with the letter A and just by chance their dropout alignment cups were labeled letter H because that is where they were in their identifying sequence.
Doug Fattic is offline  
Likes For Doug Fattic:
Old 09-18-19, 06:11 PM
  #15  
Cyclist753
Banned.
 
Join Date: Jan 2007
Posts: 297
Mentioned: 4 Post(s)
Tagged: 0 Thread(s)
Quoted: 97 Post(s)
Liked 106 Times in 66 Posts
..

Last edited by Cyclist753; 01-11-20 at 11:00 AM.
Cyclist753 is offline  
Old 09-18-19, 06:17 PM
  #16  
Cyclist753
Banned.
 
Join Date: Jan 2007
Posts: 297
Mentioned: 4 Post(s)
Tagged: 0 Thread(s)
Quoted: 97 Post(s)
Liked 106 Times in 66 Posts
..

Last edited by Cyclist753; 01-11-20 at 11:00 AM.
Cyclist753 is offline  
Old 09-18-19, 06:52 PM
  #17  
SurferRosa
señor miembro
 
SurferRosa's Avatar
 
Join Date: Dec 2018
Location: Pac NW
Posts: 8,484

Bikes: '70s - '80s Campagnolo

Mentioned: 92 Post(s)
Tagged: 0 Thread(s)
Quoted: 3846 Post(s)
Liked 6,437 Times in 3,183 Posts
RJ the bike hack shows you how to make a homemade tool.

SurferRosa is offline  
Old 09-18-19, 07:08 PM
  #18  
Prowler 
Senior Member
 
Join Date: Nov 2013
Location: Near Pottstown, PA: 30 miles NW of Philadelphia
Posts: 2,185

Bikes: 2 Trek Mtn, Cannondale R600 road, 6 vintage road bikes

Mentioned: 83 Post(s)
Tagged: 0 Thread(s)
Quoted: 470 Post(s)
Liked 1,015 Times in 397 Posts
FWIW! We get a lot of bent RD hangers at our shop. I usually charge only $10 to align them. It's quick with the Park tool and experience. The Park tool is worth it. I'm convinced that people don't pay attention when they lay the bike down, or when they hang it on a rack or put it in the car. RDs get banged all the time so the hangers get bent. I align them so they show less than 1/4" out at the rim, both directions. On my own bikes I align the hangers closer than that, after aligning the dropouts. It makes a difference in how the RD shifts, especially with indexed systems.

$75 to align the RD hanger? Either robbery or they are doing a LOT more than you've asked for. Ask many more questions!
Prowler is online now  
Old 09-18-19, 07:56 PM
  #19  
Road Fan
Senior Member
 
Road Fan's Avatar
 
Join Date: Apr 2005
Location: Ann Arbor, MI
Posts: 16,853

Bikes: 1980 Masi, 1984 Mondonico, 1984 Trek 610, 1980 Woodrup Giro, 2005 Mondonico Futura Leggera ELOS, 1967 PX10E, 1971 Peugeot UO-8

Mentioned: 49 Post(s)
Tagged: 0 Thread(s)
Quoted: 1851 Post(s)
Liked 654 Times in 498 Posts
Originally Posted by Salamandrine
Aligning the dropouts and derailleur hanger is always my first step in setting up a bike. I have the tools, which makes it easy, but it's pretty easy to improvise a hanger tool from a spare axle as shown above. The basic idea of doing this is that you rotate the tool around, and use the distance to the rear rim as a reference. If there is more space between the tool and the rim at the top then the bottom, push the arm in when it's at the top to even the distance. Same thing if there is more difference in the front vs rear when the arm is horizontal.

FYI you can get even lazier and simply use a wheel with the tire removed. Just compare the distance at various points around the rim. Even this will work 100x better than eyeballing it with a crescent wrench. IMO.

Pretty hilarious that shops are charging 75 bux nowadays. Shops I worked in did it automatically as part of yer basic $35 tuneup, or whatever it cost BITD. Took 43 seconds.
Two prerequisites to using the derailleur hanger alignment tool.

True teh wheel.

Dish the wheel.

(maybe three) As has been said, install the wheel square, so the rim is in the plane or parallel to the plane of the main triangle.

After you're done it might be good to (if you have the tool) align the rear dropouts. Might have to do the derailleur hanger again, or at least check it.
Road Fan is offline  
Old 09-18-19, 09:39 PM
  #20  
Jeff Wills
Insane Bicycle Mechanic
 
Jeff Wills's Avatar
 
Join Date: Mar 2008
Location: other Vancouver
Posts: 9,811
Mentioned: 34 Post(s)
Tagged: 0 Thread(s)
Quoted: 788 Post(s)
Liked 688 Times in 367 Posts
If you want precise alignment, get a precise tool:
https://www.efficientvelo.com/tools/...alignment-tool
I know Brett, the inventor. Genuinely nice person and brilliant bike mechanic/tool maker.
__________________
Jeff Wills

Comcast nuked my web page. It will return soon..
Jeff Wills is offline  
Old 09-19-19, 05:46 AM
  #21  
mpetry912 
aged to perfection
 
mpetry912's Avatar
 
Join Date: Jun 2009
Location: PacNW
Posts: 1,773

Bikes: Dinucci Allez 2.0, Richard Sachs, Alex Singer, Serotta, Masi GC, Raleigh Pro Mk.1, Hetchins, etc

Mentioned: 23 Post(s)
Tagged: 0 Thread(s)
Quoted: 819 Post(s)
Liked 1,219 Times in 643 Posts
You CAN eyeball it but it's hard to be accurate. As someone said above, be sure to have a wheel clamped in the frame, and check fork end alignment afterwards.

Love those EVT tools Jeff ! I have the dishing guage and it is awesome.

Mark Petry
Bainbridge Island, WA USA
mpetry912 is offline  
Old 09-19-19, 05:53 AM
  #22  
tiger1964 
Senior Member
Thread Starter
 
tiger1964's Avatar
 
Join Date: Apr 2011
Location: Maryland, USA
Posts: 2,414

Bikes: Drysdale/Gitane/Zeus/Masi/Falcon/Palo Alto/Raleigh/Legnano

Mentioned: 34 Post(s)
Tagged: 0 Thread(s)
Quoted: 966 Post(s)
Liked 613 Times in 393 Posts
Originally Posted by Prowler
FWIW! We get a lot of bent RD hangers at our shop. I usually charge only $10 to align them.
If the difference is $65, it's probably worth driving up from the MD suburbs of DC!

Originally Posted by Jeff Wills
If you want precise alignment, get a precise tool:
Wow, my checkbook balance would be precisely $500 lower. It looks beautifully made...
__________________
Larry:1958 Drysdale, 1961 Gitane Gran Sport, 1974 Zeus track, 1988 Masi Gran Corsa, 1974 Falcon, 1980 Palo Alto, 1973 Raleigh Gran Sport, 1974 Legnano. Susan: 1976 Windsor Profesional.


tiger1964 is offline  
Old 09-19-19, 06:24 AM
  #23  
fishboy316
Senior Member
 
fishboy316's Avatar
 
Join Date: Jan 2015
Location: Arnold Maryland
Posts: 330

Bikes: Cervelo S5, Cannondale AL1 Lefty MTB, Trek X01, Trek Farley 7,1951 Raleigh Sport, 57&60 Raleigh Tourist, 70 Raleigh Super Course, 80's Soma Prestiege,72 Raleigh Grand Sports, 85 Club Fuji, 76 Raleigh Competition, 85 Panasonic,70's Peugot u08. & more

Mentioned: 1 Post(s)
Tagged: 0 Thread(s)
Quoted: 39 Post(s)
Liked 25 Times in 17 Posts
Hey, Not sure where you are in Maryland but I am a P/T er at Bike Dr in Annapolis and I believe we charge $15 to align the hanger. Usually can do it while you wait. Just saying.

Bill
fishboy316 is offline  
Old 09-19-19, 07:56 AM
  #24  
tiger1964 
Senior Member
Thread Starter
 
tiger1964's Avatar
 
Join Date: Apr 2011
Location: Maryland, USA
Posts: 2,414

Bikes: Drysdale/Gitane/Zeus/Masi/Falcon/Palo Alto/Raleigh/Legnano

Mentioned: 34 Post(s)
Tagged: 0 Thread(s)
Quoted: 966 Post(s)
Liked 613 Times in 393 Posts
Originally Posted by fishboy316
Hey, Not sure where you are in Maryland but I am a P/T er at Bike Dr in Annapolis and I believe we charge $15 to align the hanger. Usually can do it while you wait. Just saying.

Bill
Thanks, let's call that Plan B if the LBS cannot help or is too much $$$. I'm just south of Goddard Space Flight Center, so 1.5-to-2 gallons of gas away. While in Annapolis, I can see if I need anything from Velo Orange too, like those dropout screws....
__________________
Larry:1958 Drysdale, 1961 Gitane Gran Sport, 1974 Zeus track, 1988 Masi Gran Corsa, 1974 Falcon, 1980 Palo Alto, 1973 Raleigh Gran Sport, 1974 Legnano. Susan: 1976 Windsor Profesional.


tiger1964 is offline  
Old 09-19-19, 09:19 AM
  #25  
unterhausen
Randomhead
 
Join Date: Aug 2008
Location: Happy Valley, Pennsylvania
Posts: 24,362
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 4 Post(s)
Liked 3,662 Times in 2,496 Posts
$75 is the retail for the park tool, isn't it?

The Cyclus looks okay https://www.bike-discount.de/en/buy/...ent-tool-25599

you can find the Shimano version of the EVT tool on ebay occasionally. Often missing parts though.
unterhausen is offline  

Thread Tools
Search this Thread

Contact Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service -

Copyright © 2024 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.