Deep Sigh
03-24-22, 09:17 AM
#1
...
Thread Starter
Join Date: Oct 2021
Location: Whitestone and Rensselaerville, New York
Posts: 1,494
Bikes: Bicycles? Yup.
Mentioned: 8 Post(s)
Tagged: 0 Thread(s)
Quoted: 477 Post(s)
Liked 1,552 Times
in
727 Posts
Deep Sigh
Finished the 3 month Centurion Prestige build. Adjusted everything on the stand. Test rode up and down the block, brifters and brakes, it's working nicely so I go to end of the block, turn left uphill and stand on the pedals. I didn't finish the second rotation when it came apart violently.
This was a tough lesson; when building on an old frame with unknown history, build and test before any cosmetic work.
Only 10 minutes to live
So, the worst has happened; n-1, and this will be rectified soon!
Last edited by BTinNYC; 03-24-22 at 09:35 AM.
Likes For BTinNYC:
Likes For 3speedslow:
03-24-22, 09:40 AM
#3
Senior Member
Join Date: Dec 2020
Location: Wake Forest, NC
Posts: 5,756
Bikes: 1989 Cinelli Supercorsa
Mentioned: 11 Post(s)
Tagged: 0 Thread(s)
Quoted: 3492 Post(s)
Liked 2,911 Times
in
1,766 Posts
Ugh. I feel your pain! I've never seen a failure like that. I wonder what kind of forces, and in what direction(s), caused such a failure.
Likes For smd4:
03-24-22, 09:46 AM
#4
Senior Member
Get it fixed. It will be worth it.
Likes For Bad Lag:
03-24-22, 09:47 AM
#5
Senior Member
Join Date: Aug 2020
Location: Saratoga, CA
Posts: 821
Bikes: 1981 Bianchi Specialissim, 1976 Colnago Super. 1971 Bob Jackson. 2012 Kestrel 4000. 2012 Willier. 2016 Fuji Cross 1.1
Mentioned: 25 Post(s)
Tagged: 0 Thread(s)
Quoted: 275 Post(s)
Liked 940 Times
in
387 Posts
Holy crap, never seen that before. Hopefully you came out of it unscathed.
Likes For BTinNYC:
03-24-22, 09:52 AM
#7
Senior Member
Join Date: Jun 2005
Location: In transit
Posts: 1,897
Bikes: 07 Vanilla, 98 IRD road frame built up with 25th Ann DA, Surly cross check with 105 comp, 78 Raleigh Comp GS, 85 Centurionelli
Mentioned: 8 Post(s)
Tagged: 0 Thread(s)
Quoted: 87 Post(s)
Liked 923 Times
in
191 Posts
03-24-22, 09:56 AM
#8
seņor miembro
Join Date: Dec 2018
Location: Pac NW
Posts: 6,602
Bikes: '70s - '80s Campagnolo
Mentioned: 92 Post(s)
Tagged: 0 Thread(s)
Quoted: 3869 Post(s)
Liked 6,460 Times
in
3,193 Posts
Likes For BTinNYC:
03-24-22, 10:18 AM
#10
Junior Member
Join Date: Nov 2018
Location: Falmouth, ME
Posts: 142
Bikes: 2010 Cannondale CAAD 5 Potenza 66cm, 1984 Basso Gap Nuovo Record 65cm, 1989 Cannondale ST Racing Triple 27", 1974 Schwinn Paramount Nuovo Record 26", 198? Scapin MKII 66cm Victory, 1994 Havnoonian Chorus 8sp 27"
Mentioned: 8 Post(s)
Tagged: 0 Thread(s)
Quoted: 45 Post(s)
Liked 101 Times
in
44 Posts
Awful... Though the half a dropout is proof positive of the enormous wattage that you clearly put out. If it were mine, I'd hang it on the wall and recount the story to houseguests. Good luck finding your n+1!
Likes For jrg1244:
03-24-22, 10:25 AM
#11
Senior Member
Join Date: Dec 2020
Location: Wake Forest, NC
Posts: 5,756
Bikes: 1989 Cinelli Supercorsa
Mentioned: 11 Post(s)
Tagged: 0 Thread(s)
Quoted: 3492 Post(s)
Liked 2,911 Times
in
1,766 Posts
I would think the force exerted would tend to pull the axle towards the front of the dropout, along the slot. What caused it to force the bottom part of the dropout (I'm guessing), down, vertically?
03-24-22, 10:39 AM
#12
Old fart
Join Date: Nov 2004
Location: Appleton WI
Posts: 24,778
Bikes: Several, mostly not name brands.
Mentioned: 153 Post(s)
Tagged: 0 Thread(s)
Quoted: 3583 Post(s)
Liked 3,395 Times
in
1,929 Posts
Usually it happens as a result of the chain jamming and pulling on the derailleur. This could have happened under a previous owner, who straightened the damage. A subsequent hard shift may have been enough to cause the failure in that previously weakened spot.
03-24-22, 10:42 AM
#13
Space Ghost
Join Date: Oct 2017
Location: NYC
Posts: 1,762
Bikes: Bridgestone, Fuji, Iro, Jamis, Gary Fisher, GT, Scott, Specialized and more
Mentioned: 3 Post(s)
Tagged: 0 Thread(s)
Quoted: 292 Post(s)
Liked 412 Times
in
318 Posts
That build came out pretty nifty. Sorry that happened.
03-24-22, 10:43 AM
#14
Senior Member
Join Date: Dec 2020
Location: Wake Forest, NC
Posts: 5,756
Bikes: 1989 Cinelli Supercorsa
Mentioned: 11 Post(s)
Tagged: 0 Thread(s)
Quoted: 3492 Post(s)
Liked 2,911 Times
in
1,766 Posts
Well, all the old books say that a great benefit of steel frames is that they can be relatively easily/cheaply repaired. Time to place that ancient wisdom into practice!
03-24-22, 11:17 AM
#15
Banned.
Join Date: Jan 2022
Posts: 1,070
Mentioned: 2 Post(s)
Tagged: 0 Thread(s)
Quoted: 359 Post(s)
Liked 582 Times
in
336 Posts
2. Worth fixing.
3. Take the picture, frame it, mount that on the wall as proof of your wattage.
4. Refine the story to generate swoonage.
03-24-22, 06:36 PM
#16
Senior Member
Join Date: Jun 2010
Location: Medford MA
Posts: 2,089
Bikes: Ron Cooper touring, 1959 Jack Taylor 650b ladyback touring tandem, Vitus 979, Joe Bell painted Claud Butler Dalesman, Colin Laing curved tube tandem, heavily-Dilberted 1982 Trek 6xx, René Herse tandem
Mentioned: 80 Post(s)
Tagged: 0 Thread(s)
Quoted: 964 Post(s)
Liked 1,451 Times
in
723 Posts
Long drive, but...
Come to Harvard and I'll MIG it for you.
Bring a nice Calvados or green chartreuse and be prepared for an evening of fun.
My prior dropout work is here. I'm confident I can do this. Super easy, especially if you can forego the adjuster. I can redrill and tap the adjuster as well, just a bit more work.
Come to Harvard and I'll MIG it for you.
Bring a nice Calvados or green chartreuse and be prepared for an evening of fun.
My prior dropout work is here. I'm confident I can do this. Super easy, especially if you can forego the adjuster. I can redrill and tap the adjuster as well, just a bit more work.
__________________
Owner & co-founder, Cycles René Hubris. Unfortunately attaching questionable braze-ons to perfectly good frames since about 2015. With style.
Owner & co-founder, Cycles René Hubris. Unfortunately attaching questionable braze-ons to perfectly good frames since about 2015. With style.
Likes For scarlson:
03-24-22, 06:47 PM
#17
...
Thread Starter
Join Date: Oct 2021
Location: Whitestone and Rensselaerville, New York
Posts: 1,494
Bikes: Bicycles? Yup.
Mentioned: 8 Post(s)
Tagged: 0 Thread(s)
Quoted: 477 Post(s)
Liked 1,552 Times
in
727 Posts
Long drive, but...
Come to Harvard and I'll MIG it for you.
Bring a nice Calvados or green chartreuse and be prepared for an evening of fun.
My prior dropout work is here. I'm confident I can do this. Super easy, especially if you can forego the adjuster. I can redrill and tap the adjuster as well, just a bit more work.
Come to Harvard and I'll MIG it for you.
Bring a nice Calvados or green chartreuse and be prepared for an evening of fun.
My prior dropout work is here. I'm confident I can do this. Super easy, especially if you can forego the adjuster. I can redrill and tap the adjuster as well, just a bit more work.
03-24-22, 07:03 PM
#18
Senior Member
Join Date: Jun 2010
Location: Medford MA
Posts: 2,089
Bikes: Ron Cooper touring, 1959 Jack Taylor 650b ladyback touring tandem, Vitus 979, Joe Bell painted Claud Butler Dalesman, Colin Laing curved tube tandem, heavily-Dilberted 1982 Trek 6xx, René Herse tandem
Mentioned: 80 Post(s)
Tagged: 0 Thread(s)
Quoted: 964 Post(s)
Liked 1,451 Times
in
723 Posts
Sure I would. For a bottle of green chartreuse and some agreeable company. Would also consider aņejo mezcal or tequila. You know, the stuff that's been aged on oak. Come over on the megabus, tell them it's a folding bike, they won't know!
I'd rather do that than try to source another dropout, melt and grind and file the old one out, prep everything, and braze it. The bottom of the dropout doesn't see much stress. This is way easier than the one I just did, linked to above. Only risky thing is trying to drill through the weld and tapping that hole for the adjuster. Much easier and stronger if you forego the adjuster on that side. But I can drill it too, if you must.
I'd rather do that than try to source another dropout, melt and grind and file the old one out, prep everything, and braze it. The bottom of the dropout doesn't see much stress. This is way easier than the one I just did, linked to above. Only risky thing is trying to drill through the weld and tapping that hole for the adjuster. Much easier and stronger if you forego the adjuster on that side. But I can drill it too, if you must.
__________________
Owner & co-founder, Cycles René Hubris. Unfortunately attaching questionable braze-ons to perfectly good frames since about 2015. With style.
Owner & co-founder, Cycles René Hubris. Unfortunately attaching questionable braze-ons to perfectly good frames since about 2015. With style.
03-24-22, 07:09 PM
#19
feros ferio
Join Date: Jul 2000
Location: www.ci.encinitas.ca.us
Posts: 21,793
Bikes: 1959 Capo Modell Campagnolo; 1960 Capo Sieger (2); 1962 Carlton Franco Suisse; 1970 Peugeot UO-8; 1982 Bianchi Campione d'Italia; 1988 Schwinn Project KOM-10;
Mentioned: 44 Post(s)
Tagged: 0 Thread(s)
Quoted: 1391 Post(s)
Liked 1,322 Times
in
835 Posts
This is the one argument in favor of stamped dropouts over forged.
It is also possible that the dropouts were not properly aligned, or that the previous owner had broken a rear axle and stressed the drive side dropout in the process.
It is also possible that the dropouts were not properly aligned, or that the previous owner had broken a rear axle and stressed the drive side dropout in the process.
__________________
"Far and away the best prize that life offers is the chance to work hard at work worth doing." --Theodore Roosevelt
Capo: 1959 Modell Campagnolo, S/N 40324; 1960 Sieger (2), S/N 42624, 42597
Carlton: 1962 Franco Suisse, S/N K7911
Peugeot: 1970 UO-8, S/N 0010468
Bianchi: 1982 Campione d'Italia, S/N 1.M9914
Schwinn: 1988 Project KOM-10, S/N F804069
"Far and away the best prize that life offers is the chance to work hard at work worth doing." --Theodore Roosevelt
Capo: 1959 Modell Campagnolo, S/N 40324; 1960 Sieger (2), S/N 42624, 42597
Carlton: 1962 Franco Suisse, S/N K7911
Peugeot: 1970 UO-8, S/N 0010468
Bianchi: 1982 Campione d'Italia, S/N 1.M9914
Schwinn: 1988 Project KOM-10, S/N F804069
03-24-22, 09:14 PM
#20
Bikes are okay, I guess.
Join Date: Jan 2015
Location: Richmond, Virginia
Posts: 6,938
Bikes: Waterford Paramount Touring, Giant CFM-2, Raleigh Sports 3-speeds in M23 & L23, Schwinn Cimarron oddball build, Marin Palisades Trail dropbar conversion, Nishiki Cresta GT
Mentioned: 69 Post(s)
Tagged: 0 Thread(s)
Quoted: 2647 Post(s)
Liked 2,446 Times
in
1,557 Posts
"...so there I was, rolling easily along at about 8/10ths when I decided to pour on the coal..." Etc., etc.
03-25-22, 01:32 AM
#21
Me duelen las nalgas
Join Date: Aug 2015
Location: Texas
Posts: 13,513
Bikes: Centurion Ironman, Trek 5900, Univega Via Carisma, Globe Carmel
Mentioned: 199 Post(s)
Tagged: 0 Thread(s)
Quoted: 4559 Post(s)
Liked 2,802 Times
in
1,800 Posts
Any signs of corrosion in the threads of the adjuster hole? Just grasping at straws here.
That's gonna be a pretty build once it's back together.
That's gonna be a pretty build once it's back together.
Likes For plonz:
03-25-22, 05:19 AM
#24
Senior Member
Join Date: Jun 2018
Location: SW Ohio
Posts: 2,397
Mentioned: 93 Post(s)
Tagged: 0 Thread(s)
Quoted: 1104 Post(s)
Liked 1,824 Times
in
878 Posts
I've seen that before. In those cases, it was from putting a longer OLD axle in frame designed for 120/126mm without cold setting and making sure the dropout faces were parallel to each other. Mind you, that's not what I'm saying is the case here.
__________________
03-25-22, 07:28 AM
#25
...
Thread Starter
Join Date: Oct 2021
Location: Whitestone and Rensselaerville, New York
Posts: 1,494
Bikes: Bicycles? Yup.
Mentioned: 8 Post(s)
Tagged: 0 Thread(s)
Quoted: 477 Post(s)
Liked 1,552 Times
in
727 Posts
I will very closely check the DOs after fixing.
I did not successfully cold set because the stays were like spring steel (wouldn't hold a mm of bend, even after spreading to 165mm, yet relatively easy to spread by hand) and now my check for parallel with a homemade tool feels cursory.
Edit PS
Wouldn't that misalignment become evident while setting up the RD?
Last edited by BTinNYC; 03-25-22 at 08:39 AM.