How important is frame size?
#1
Junior Member
Thread Starter
How important is frame size?
We went down to the LBS for a new MTB and brought a bike I know I like the feel of, my Trek Roscoe 6. Tried a few bikes Scott acent, Canondale trail SE and GT Avalanche Expert. Went with the expert. Didn't have a dropper post, but had the 1x12 I wanted a better fork (Rockshox Recon vs Suntours on the Canondale and the Rockshox Reba on the Scott) I figured for less money, the nicer fork was a plus, I think the other two had smaller cassettes too. But that may be level dependent and not a huge issue. Either way, they all seemed comparable and nothing night and day different. I was sent away with a med frame on the GT and I ride a Med on the Trek too. But on the GT webpage they say the Med is for a 5'8 to 5'11 person. I am not experienced enough to know what a "perfect" fit feels like. I can stand over the bike in flat shoes and just clear the top bar. They said they could try the small if I really felt it was too large but that it looked good. Riding it, it's so much better than my last 400 dollar bike that it's night and day. Huge step up. Should I really even think about Sm vs Med frame size and is this something that will matter more as I get more experience doing this? Thanks for the replies, over all, it's nice that both of us have upgraded!
#2
Senior Member
You didn't mention how tall you are. Manufactures have different measurements with their frames. For example, I am a L or XL depending how the manufacture designs the frame.
To answer the question in the title, a frame being the correct size is the most important thing when selecting a bike. If you are between sizes, finding the correct size is something you need to figure out. Take both bikes on a 20-30 minute test ride (longer if possible) and pick which feels best.
To answer the question in the title, a frame being the correct size is the most important thing when selecting a bike. If you are between sizes, finding the correct size is something you need to figure out. Take both bikes on a 20-30 minute test ride (longer if possible) and pick which feels best.
#3
Senior Member
Join Date: Jul 2007
Location: South shore, L.I., NY
Posts: 6,175
Bikes: Flyxii FR322, Cannondale Topstone, Miyata City Liner, Specialized Chisel, Specialized Epic Evo
Mentioned: 18 Post(s)
Tagged: 0 Thread(s)
Quoted: 2760 Post(s)
Liked 1,484 Times
in
863 Posts
If you are happy with the fit on your Trek, why not just measure reach of saddle to mid stem on the GT and match it or get really close ?
#4
Senior Member
Join Date: May 2022
Location: USA
Posts: 1,517
Bikes: Cannondale - Gary Fisher - Litespeed - Schwinn Paramount - Schwinn (lugged steel) - Trek OCLV
Mentioned: 1 Post(s)
Tagged: 0 Thread(s)
Quoted: 679 Post(s)
Liked 634 Times
in
430 Posts
for off road riding - especially tight technical off road riding - the amount of standover clearance does not appear to be ideal
but I don't know your primary type of riding - and obviously have not seen you on the bike
how is the length ... top tube length ?
what is your height ?
but I don't know your primary type of riding - and obviously have not seen you on the bike
how is the length ... top tube length ?
what is your height ?
#5
Senior Member
Join Date: May 2010
Location: Bastrop Texas
Posts: 3,689
Bikes: Univega, Peu P6, Peu PR-10, Ted Williams, Peu UO-8, Peu UO-18 Mixte, Peu Dolomites
Mentioned: 8 Post(s)
Tagged: 0 Thread(s)
Quoted: 652 Post(s)
Liked 1,039 Times
in
669 Posts
When I was at 300 pounds plus I rode a big heavy duty ChroMo 80's FUJI till I got my weight down. Called it my horse cause I had to jump on and off of it. The only reason I was able to do it was because of my years of experience ridding 70's road bikes.
My suggestion to you is not to get a bike that is too big for you. Especially if you don't have allot of experience ridding...
My suggestion to you is not to get a bike that is too big for you. Especially if you don't have allot of experience ridding...
__________________
No matter where your at... There you are... Δf:=f(1/2)-f(-1/2)
Likes For zandoval:
#6
Junior Member
Thread Starter
You didn't mention how tall you are. Manufactures have different measurements with their frames. For example, I am a L or XL depending how the manufacture designs the frame.
To answer the question in the title, a frame being the correct size is the most important thing when selecting a bike. If you are between sizes, finding the correct size is something you need to figure out. Take both bikes on a 20-30 minute test ride (longer if possible) and pick which feels best.
To answer the question in the title, a frame being the correct size is the most important thing when selecting a bike. If you are between sizes, finding the correct size is something you need to figure out. Take both bikes on a 20-30 minute test ride (longer if possible) and pick which feels best.
#7
Newbie
I picked up the same bike this spring. I’m 5’11” with a 31” inseam. Stand over height feels perfect but the reach feels a little cramped. Their sizing information is just a guide and not going to be perfect for everyone. Sounds like you got the right size.
#8
Junior Member
Thread Starter
And standing over the Trek Roscoe 6, the top tube comes up quicker and seems as close/closer. There's maybe a half inch difference if you sit them side by side, and the Trek is supposed to fit down to 5'4. I'm just not sure how to be sure since I'm an amateur. Trust the LBS who said I was good, or trust the "sizing guide" that says go for a small.
#9
Senior Member
Join Date: Jun 2005
Location: Kentucky
Posts: 2,442
Bikes: 06 Lemond Reno, 98 GT Timberline mtn.bike
Mentioned: 7 Post(s)
Tagged: 0 Thread(s)
Quoted: 376 Post(s)
Liked 603 Times
in
379 Posts
Sizing "guides" are just that--a general guide, and are not correct for everyone. I had considered a hybrid once, and like the Trek FX line. Trek's sizing guide indicated a medium was the right size. Went to a dealer, medium was much too small, while a large was perfect. A guide might get you in the ballpark but it's no substitute for actually riding the bike. Didn't buy a hybrid-decided didn't really need one.
Last edited by freeranger; 10-03-22 at 06:23 AM.
Likes For freeranger:
#10
Advanced Slacker
Join Date: Feb 2017
Posts: 5,879
Bikes: Soma Fog Cutter, Surly Wednesday, Canfielld Tilt
Mentioned: 26 Post(s)
Tagged: 0 Thread(s)
Quoted: 2615 Post(s)
Liked 2,338 Times
in
1,320 Posts
I suggest dropping the focus on standover. Sizing modern MTB bikes using standover is a bad idea, and nobody who understands modern MTB fit well would do so.
Go by the length of the reach and how it feels actually riding it.
Frame size for mtb IS very important, because getting the proper frame reach is very important. At least if you are going to be riding technical terrain. If the bike is for more casual riding or mostly paths and rail-trail stuff then you have more leeway to make adjustments with stems length and such.
At 5’6” you could be a med on some bikes and small on others.
If you do decide to make standover a deciding factor (which is a big mistake, IMO) then look for a model that has standover AND proper reach. Going down a size in a particular model just to get more standover can leave you with too small of a frame for the 99% of the time you are riding it rather than standing over it.
As far as whether to go with the shops rec or the manufacturer’s guide… depends on the shop. Did they have you ride the bike around the parking lot and see how you positioned yourself or did you just sit on it in the shop?
Try searching forums like MTBR (there is a Trek sub-forum there) to see how others sizes up on Roscoes.
Go by the length of the reach and how it feels actually riding it.
Frame size for mtb IS very important, because getting the proper frame reach is very important. At least if you are going to be riding technical terrain. If the bike is for more casual riding or mostly paths and rail-trail stuff then you have more leeway to make adjustments with stems length and such.
At 5’6” you could be a med on some bikes and small on others.
If you do decide to make standover a deciding factor (which is a big mistake, IMO) then look for a model that has standover AND proper reach. Going down a size in a particular model just to get more standover can leave you with too small of a frame for the 99% of the time you are riding it rather than standing over it.
As far as whether to go with the shops rec or the manufacturer’s guide… depends on the shop. Did they have you ride the bike around the parking lot and see how you positioned yourself or did you just sit on it in the shop?
Try searching forums like MTBR (there is a Trek sub-forum there) to see how others sizes up on Roscoes.
#11
Junior Member
Thread Starter
I suggest dropping the focus on standover. Sizing modern MTB bikes using standover is a bad idea, and nobody who understands modern MTB fit well would do so.
Go by the length of the reach and how it feels actually riding it.
Frame size for mtb IS very important, because getting the proper frame reach is very important. At least if you are going to be riding technical terrain. If the bike is for more casual riding or mostly paths and rail-trail stuff then you have more leeway to make adjustments with stems length and such.
At 5’6” you could be a med on some bikes and small on others.
If you do decide to make standover a deciding factor (which is a big mistake, IMO) then look for a model that has standover AND proper reach. Going down a size in a particular model just to get more standover can leave you with too small of a frame for the 99% of the time you are riding it rather than standing over it.
As far as whether to go with the shops rec or the manufacturer’s guide… depends on the shop. Did they have you ride the bike around the parking lot and see how you positioned yourself or did you just sit on it in the shop?
Try searching forums like MTBR (there is a Trek sub-forum there) to see how others sizes up on Roscoes.
Go by the length of the reach and how it feels actually riding it.
Frame size for mtb IS very important, because getting the proper frame reach is very important. At least if you are going to be riding technical terrain. If the bike is for more casual riding or mostly paths and rail-trail stuff then you have more leeway to make adjustments with stems length and such.
At 5’6” you could be a med on some bikes and small on others.
If you do decide to make standover a deciding factor (which is a big mistake, IMO) then look for a model that has standover AND proper reach. Going down a size in a particular model just to get more standover can leave you with too small of a frame for the 99% of the time you are riding it rather than standing over it.
As far as whether to go with the shops rec or the manufacturer’s guide… depends on the shop. Did they have you ride the bike around the parking lot and see how you positioned yourself or did you just sit on it in the shop?
Try searching forums like MTBR (there is a Trek sub-forum there) to see how others sizes up on Roscoes.
#12
Industry guy
There is no advantage to a bicycle to big for the rider, or one to much to small either.
A really long or really short stem affect steering and handling.
A super long seatpost or one jambed way is affect pedaling geometry.
A good fit is essential.
BTW, the top bar always wins!
rusty
A really long or really short stem affect steering and handling.
A super long seatpost or one jambed way is affect pedaling geometry.
A good fit is essential.
BTW, the top bar always wins!
rusty
Likes For 100bikes:
#13
Junior Member
Thread Starter
There is no advantage to a bicycle to big for the rider, or one to much to small either.
A really long or really short stem affect steering and handling.
A super long seatpost or one jambed way is affect pedaling geometry.
A good fit is essential.
BTW, the top bar always wins!
rusty
A really long or really short stem affect steering and handling.
A super long seatpost or one jambed way is affect pedaling geometry.
A good fit is essential.
BTW, the top bar always wins!
rusty
#14
Senior Member
Join Date: Jan 2013
Location: Norman, Oklahoma
Posts: 5,250
Bikes: Too many to list
Mentioned: 36 Post(s)
Tagged: 0 Thread(s)
Quoted: 1718 Post(s)
Liked 1,038 Times
in
688 Posts
I cant straddle the top tube on several dual suspension bikes i have had (and have )
Granted -- a dual suspension bike is a different animal, - but just throwing that out there for the folks that claim you need to have top tube clearance in all cases
Granted -- a dual suspension bike is a different animal, - but just throwing that out there for the folks that claim you need to have top tube clearance in all cases
Likes For DMC707:
#15
Senior Member
Join Date: Sep 2006
Location: Paradise, TX
Posts: 2,085
Bikes: Soma Pescadero, Surly Pugsley, Salsa Fargo, Schwinn Klunker, Gravity SS 27.5, Monocog 29er
Mentioned: 1 Post(s)
Tagged: 0 Thread(s)
Quoted: 186 Post(s)
Liked 230 Times
in
163 Posts
Standover doesn't matter when riding. Proper sizing and fit is based on cockpit length.
#16
Senior Member
Join Date: Jul 2014
Location: socal
Posts: 3,725
Mentioned: 8 Post(s)
Tagged: 0 Thread(s)
Quoted: 746 Post(s)
Liked 582 Times
in
441 Posts
If you're comfortable, IMO it's settled. My wife, 5'5" but long legged for her height, rides a M Felt 29er better than any of her previous bikes. Standover may be over-valued since (normally) you don't put both feet on the ground simultaneously when stopping.
Likes For 2old:
#17
Advanced Slacker
Join Date: Feb 2017
Posts: 5,879
Bikes: Soma Fog Cutter, Surly Wednesday, Canfielld Tilt
Mentioned: 26 Post(s)
Tagged: 0 Thread(s)
Quoted: 2615 Post(s)
Liked 2,338 Times
in
1,320 Posts
To put standover into perspective for me:
I’ve been riding a new MTB since April. I have never checked the standover. And until I checked yesterday, I had no idea if I have any. Turns out i don’t.
I ride very technical terrain, and regularly need to bail or put a foot down. Never notice the standover.
I’ve been riding a new MTB since April. I have never checked the standover. And until I checked yesterday, I had no idea if I have any. Turns out i don’t.
I ride very technical terrain, and regularly need to bail or put a foot down. Never notice the standover.
#18
Senior Member
Join Date: Sep 2006
Location: Paradise, TX
Posts: 2,085
Bikes: Soma Pescadero, Surly Pugsley, Salsa Fargo, Schwinn Klunker, Gravity SS 27.5, Monocog 29er
Mentioned: 1 Post(s)
Tagged: 0 Thread(s)
Quoted: 186 Post(s)
Liked 230 Times
in
163 Posts
To put standover into perspective for me:
I’ve been riding a new MTB since April. I have never checked the standover. And until I checked yesterday, I had no idea if I have any. Turns out i don’t.
I ride very technical terrain, and regularly need to bail or put a foot down. Never notice the standover.
I’ve been riding a new MTB since April. I have never checked the standover. And until I checked yesterday, I had no idea if I have any. Turns out i don’t.
I ride very technical terrain, and regularly need to bail or put a foot down. Never notice the standover.
#19
Advanced Slacker
Join Date: Feb 2017
Posts: 5,879
Bikes: Soma Fog Cutter, Surly Wednesday, Canfielld Tilt
Mentioned: 26 Post(s)
Tagged: 0 Thread(s)
Quoted: 2615 Post(s)
Liked 2,338 Times
in
1,320 Posts
Whenever I dab a foot, I am also going to be leaning the bike in that direction, anyway. With the non-dabbing foot on the other pedal, you have a lot more clearance.
Also, in those times when I do go over due to not being able to plant a foot on the ground, it is the saddle - not the top tube - that is in my way.
Likes For Kapusta:
#20
Steel is real
Join Date: Mar 2013
Posts: 855
Bikes: 1992Giant Tourer,1992MeridaAlbon,1996Scapin,1997KonaKilaueua,1993Peugeot Prestige,1991RaleighTeamZ(to be upgraded),1998 Jamis Dragon(to be built),1992CTWallis(to be built),1998VettaTeam(to be built),1995Coppi(to be built),1993Grandis(to be built)
Mentioned: 1 Post(s)
Tagged: 0 Thread(s)
Quoted: 202 Post(s)
Liked 330 Times
in
208 Posts
A too tall or a too small frame can have bad consequences on your back or kness and on your position in the cockpit, also don't cut the steering pivot too much other wise it would impact your back badly. I always had 17.5 -18 inch sloping MTB frames. I always made sure before having my bikes assembled that the riding position would suit me.
#21
Clark W. Griswold
Join Date: Mar 2014
Location: ,location, location
Posts: 11,465
Bikes: Foundry Chilkoot Ti W/Ultegra Di2, Salsa Timberjack Ti, Cinelli Mash Work RandoCross Fun Time Machine, 1x9 XT Parts Hybrid, Co-Motion Cascadia, Specialized Langster, Phil Wood Apple VeloXS Frame (w/DA 7400), R+M Supercharger2 Rohloff, Habanero Ti 26
Mentioned: 48 Post(s)
Tagged: 0 Thread(s)
Quoted: 3555 Post(s)
Liked 2,883 Times
in
1,929 Posts
Fit is always important on any frame that you plan on riding. Standover not so much but actual fit on the bike is supremely important and really the most important because if they bike doesn't fit you and you aren't comfortable on it size wise you aren't going to ride it and enjoy it so why buy it.
#22
Junior Member
Thread Starter
Fit is always important on any frame that you plan on riding. Standover not so much but actual fit on the bike is supremely important and really the most important because if they bike doesn't fit you and you aren't comfortable on it size wise you aren't going to ride it and enjoy it so why buy it.
Likes For n2t:
#23
Senior Member
Join Date: Jul 2008
Location: 25 miles northwest of Boston
Posts: 28,767
Bikes: Bottecchia Sprint, GT Timberline 29r, Marin Muirwoods 29er, Trek FX Alpha 7.0
Mentioned: 109 Post(s)
Tagged: 0 Thread(s)
Quoted: 4986 Post(s)
Liked 3,111 Times
in
2,063 Posts
#24
Senior Member
Join Date: Jul 2008
Location: 25 miles northwest of Boston
Posts: 28,767
Bikes: Bottecchia Sprint, GT Timberline 29r, Marin Muirwoods 29er, Trek FX Alpha 7.0
Mentioned: 109 Post(s)
Tagged: 0 Thread(s)
Quoted: 4986 Post(s)
Liked 3,111 Times
in
2,063 Posts
#25
Senior Member
Join Date: Jul 2008
Location: 25 miles northwest of Boston
Posts: 28,767
Bikes: Bottecchia Sprint, GT Timberline 29r, Marin Muirwoods 29er, Trek FX Alpha 7.0
Mentioned: 109 Post(s)
Tagged: 0 Thread(s)
Quoted: 4986 Post(s)
Liked 3,111 Times
in
2,063 Posts
To put standover into perspective for me:
I’ve been riding a new MTB since April. I have never checked the standover. And until I checked yesterday, I had no idea if I have any. Turns out i don’t.
I ride very technical terrain, and regularly need to bail or put a foot down. Never notice the standover.
I’ve been riding a new MTB since April. I have never checked the standover. And until I checked yesterday, I had no idea if I have any. Turns out i don’t.
I ride very technical terrain, and regularly need to bail or put a foot down. Never notice the standover.
how do you bail
what is dabbing?