Breakage of cable threads
#1
Full Member
Thread Starter
Breakage of cable threads
I was told in the past year by a bike mechanic that tightening the allen bolt down on a cable too tight can cause the threads to break (thus resulting in having to buy a new cable when too many of the threads have broken ). True or not? A biker friend said no and a self-professed ego
mechanic claimed there are only 2 ways cable threads break, one of them being when the cable gets bent. Which he then proceeded to do as he finished my installation of the pictured brake cable. (When I asked him why he'd done that if it can cause the threads to break, he gave me a laughable response.)
mechanic claimed there are only 2 ways cable threads break, one of them being when the cable gets bent. Which he then proceeded to do as he finished my installation of the pictured brake cable. (When I asked him why he'd done that if it can cause the threads to break, he gave me a laughable response.)
Likes For bboy314:
#3
I'm good to go!
Join Date: Jul 2017
Location: Mississippi
Posts: 14,945
Bikes: Tarmac Disc Comp Di2 - 2020
Mentioned: 51 Post(s)
Tagged: 0 Thread(s)
Quoted: 6173 Post(s)
Liked 4,790 Times
in
3,305 Posts
When talking about ropes and cables they are called strands.
This is another case where it depends. As well it might be more a thing of vintage days when cables were not as good a steel as they are now.
Most cables today will probably survive any tightening and you'd either break the pinch bolt or strip the corners off the hex that your wrench fits in or on. Though I can see where some cheap'o designs might smash the cable strands and then let them break from getting work hardened over time as they flex. Sort of like when you bend a coat hanger wire multiple times to break it at a certain point.
This is another case where it depends. As well it might be more a thing of vintage days when cables were not as good a steel as they are now.
Most cables today will probably survive any tightening and you'd either break the pinch bolt or strip the corners off the hex that your wrench fits in or on. Though I can see where some cheap'o designs might smash the cable strands and then let them break from getting work hardened over time as they flex. Sort of like when you bend a coat hanger wire multiple times to break it at a certain point.
Last edited by Iride01; 03-24-22 at 01:27 PM.
Likes For Iride01:
#4
Senior Member
Join Date: Aug 2005
Location: Pittsburgh, PA
Posts: 33,656
Bikes: '96 Litespeed Catalyst, '05 Litespeed Firenze, '06 Litespeed Tuscany, '20 Surly Midnight Special, All are 3x10. It is hilly around here!
Mentioned: 39 Post(s)
Tagged: 0 Thread(s)
Quoted: 2026 Post(s)
Likes: 0
Liked 1,095 Times
in
741 Posts
I think overtightening the pinch bolt enough to sever the cable strands would probably break the bolt or strip the threads in the brake arm first. As to bending the cable, yes, repetitive bending and straightening can eventually cause it to break from fatigue but one bend like you picture is harmless.
#5
Senior Member
Join Date: Oct 2014
Location: Portland, OR
Posts: 12,890
Bikes: (2) ti TiCycles, 2007 w/ triple and 2011 fixed, 1979 Peter Mooney, ~1983 Trek 420 now fixed and ~1973 Raleigh Carlton Competition gravel grinder
Mentioned: 129 Post(s)
Tagged: 0 Thread(s)
Quoted: 4788 Post(s)
Liked 3,914 Times
in
2,545 Posts
Also, the details of the clamp matter a lot. Are the edges rounded? Are there sharp edges to hole in the bolt the cable goes through? Does that hole line up nicely with the flat or groove the cable sits can mean that too tight a nut will damage strands. Flip side - more than tight enough? Why? Yes, for brakes, especially front brakes, tight enough is critical but still, we don't need more. And compromised strands means we've just eaten away at the safety factor we were tightening that nut to achieve.
Likes For 79pmooney:
#6
Senior Member
Join Date: Feb 2007
Posts: 1,415
Mentioned: 5 Post(s)
Tagged: 0 Thread(s)
Quoted: 612 Post(s)
Likes: 0
Liked 387 Times
in
270 Posts
I find that I don't need to mash the cable with the pinch bolt to the point of strand separation. The design of the cable pinch system is the deciding factor in how tight.
#7
Senior Member
Join Date: Jun 2002
Location: San Jose, CA
Posts: 3,676
Bikes: Too many bikes, too little time to ride
Mentioned: 2 Post(s)
Tagged: 0 Thread(s)
Quoted: 425 Post(s)
Liked 452 Times
in
311 Posts
Can happen, especially if you reclamp the cable at a bend or where the strands have already flattened out. More of a function of repeated unclamping/reclamping and less of a function of overtightening just once.
#8
Senior Member
Join Date: Nov 2010
Location: Minnesota
Posts: 855
Bikes: Cannondale '92 T600 '95 H600 '01 RT1000
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 92 Post(s)
Liked 109 Times
in
82 Posts
a self-professed ego mechanic claimed there are only 2 ways cable threads break, one of them being when the cable gets bent. Which he then proceeded to do as he finished my installation of the pictured brake cable. (When I asked him why he'd done that if it can cause the threads to break, he gave me a laughable response.)
#9
Senior Member
Join Date: Jul 2013
Location: NJ, USA
Posts: 1,278
Bikes: two blacks, a blue and a white.
Mentioned: 2 Post(s)
Tagged: 0 Thread(s)
Quoted: 444 Post(s)
Liked 844 Times
in
408 Posts
Those bolts don't need to be that tight on decent groupset. 7Nm should be about as much as you need.
torque wisdom here
torque wisdom here
#10
señor miembro
Join Date: Dec 2018
Location: Pac NW
Posts: 6,597
Bikes: '70s - '80s Campagnolo
Mentioned: 92 Post(s)
Tagged: 0 Thread(s)
Quoted: 3861 Post(s)
Liked 6,450 Times
in
3,190 Posts
I'd be more worried about stripping the bolt threads.
I don't use a wrench, only a socket driver or allen key (with my hand close to the bend).
I don't use a wrench, only a socket driver or allen key (with my hand close to the bend).
#11
Full Member
Thread Starter
Ok. Thanks for all the responses.
#12
Senior Member
Join Date: Dec 2019
Posts: 953
Mentioned: 3 Post(s)
Tagged: 0 Thread(s)
Quoted: 321 Post(s)
Liked 263 Times
in
212 Posts
Interesting question. I've definitely broken cables by overtightening. But that was years ago, I was a kid and an idiot, but most importantly the clamps would have been steel the same as the cable. Most clamps now are aluminium and you often see a small impression of the cable into the soft aluminium. So it may be that it can't happen any more. I still don't overtighten those things though (no reason to).