Poor shifting with 11 speed 105 setup
#1
Senior Member
Thread Starter
Join Date: Dec 2020
Location: Los Angeles
Posts: 917
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 445 Post(s)
Liked 1,040 Times
in
440 Posts
Poor shifting with 11 speed 105 setup
On my road bike, I'm currently running 11 speed 105 5800 shifters, 5800 FD, R7000 50/34t crankset, R7000 RD with a 105 11-32t cassette. For some reason, I can't get the setup to shift smoothly throughout the entire 11 speed range. If I optimize shifting for the small cogs, the big cogs suffer and if I optimize for the big cogs, the small cogs suffer. I checked the derailleur hanger and it looks straight, also I recently just replaced the RD (it's brand new) with brand new shift cabling. Compared to my 10 speed gravel bike, that bike shifts perfectly throughout the entire range (with nice spacious gaps between cogs). The only difference I can see between the two bikes is that my gravel bike has a gentler shift cable line (less bend) to get to the RD. On my road bike, cabling routes towards the bottom bracket and is screwed in place through plastic inner cabling tubes before arriving to the RD. I'm wondering if that's a possible issue with too much bend or some other problem I haven't realized?
Any advice would be appreciated! Thanks!
Any advice would be appreciated! Thanks!
#2
Guest
Join Date: Sep 2020
Posts: 2,888
Mentioned: 13 Post(s)
Tagged: 0 Thread(s)
Quoted: 1346 Post(s)
Liked 3,270 Times
in
1,439 Posts
You can't reliably eyeball a derailleur hanger. Take it in for an actual alignment; it only takes a few minutes and should be very inexpensive. If nothing else, it will rule that out as the cause of your shifting problems.
Likes For Rolla:
#4
Guest
Join Date: Sep 2020
Posts: 2,888
Mentioned: 13 Post(s)
Tagged: 0 Thread(s)
Quoted: 1346 Post(s)
Liked 3,270 Times
in
1,439 Posts
Yes; being able to shift well on some cogs but not others often points to an alignment issue. Again, it's nice to rule it out so you aren't needlessly chasing other things, like cable tension. While you're at the shop, have them measure the teeth and the chain for wear. This is also easy to do and shouldn't take long. At my shop, we'd do it while you wait or within a couple of hours.
#5
Senior Member
Thread Starter
Join Date: Dec 2020
Location: Los Angeles
Posts: 917
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 445 Post(s)
Liked 1,040 Times
in
440 Posts
Yes; being able to shift well on some cogs but not others often points to an alignment issue. Again, it's nice to rule it out so you aren't needlessly chasing other things, like cable tension. While you're at the shop, have them measure the teeth and the chain for wear. This is also easy to do and shouldn't take long. At my shop, we'd do it while you wait or within a couple of hours.
Likes For jonathanf2:
#6
Guest
Join Date: Sep 2020
Posts: 2,888
Mentioned: 13 Post(s)
Tagged: 0 Thread(s)
Quoted: 1346 Post(s)
Liked 3,270 Times
in
1,439 Posts
When I redid the RD cabling, I re-used the old inner plastic cable tubing for the internal routing. I was thinking of getting fresh tubing if that might cause some friction or other issues. I don't think it's the cassette teeth or chain either, both are new. If it is the derailleur hanger, do you think I'll need to order a new hanger? Thanks!
You can usually straighten a hanger if it's only slightly bent; we're talking millimeters, here. Should you need a new hanger, just be aware that there are dozens and dozens of them, and each is specific to the frame; you have to get the right one.
#7
Senior Member
Thread Starter
Join Date: Dec 2020
Location: Los Angeles
Posts: 917
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 445 Post(s)
Liked 1,040 Times
in
440 Posts
It doesn't sound like a friction issue to me; that would affect shifting in every cog, not just some of them. But unless I have the bike in the stand in front of me, I can't diagnose this with any accuracy.
You can usually straighten a hanger if it's only slightly bent; we're talking millimeters, here. Should you need a new hanger, just be aware that there are dozens and dozens of them, and each is specific to the frame; you have to get the right one.
You can usually straighten a hanger if it's only slightly bent; we're talking millimeters, here. Should you need a new hanger, just be aware that there are dozens and dozens of them, and each is specific to the frame; you have to get the right one.
#8
Junior Member
I run a 105 eleven speed on my gravel bike and I have two observations about shifting issues like this. The first is the derailleur spring seems a little weak and has been since new. The other is that the cable housing wear has an impact on shifting to higher gears. My housing sticks a little and combined with a weak spring to start with seems make shifting adjustments a bit touchy. Hope this helps.
Likes For OshkoshBiker:
#9
Guest
Join Date: Sep 2020
Posts: 2,888
Mentioned: 13 Post(s)
Tagged: 0 Thread(s)
Quoted: 1346 Post(s)
Liked 3,270 Times
in
1,439 Posts
Carrying a spare hanger is always a good idea. I wish manufacturers would supply one with their bikes.
Likes For Rolla:
#10
Senior Member
Join Date: Jul 2006
Location: San Jose (Willow Glen) Ca
Posts: 9,834
Bikes: Kirk Custom JK Special, '84 Team Miyata,(dura ace old school) 80?? SR Semi-Pro 600 Arabesque
Mentioned: 106 Post(s)
Tagged: 0 Thread(s)
Quoted: 2337 Post(s)
Liked 2,811 Times
in
1,535 Posts
fwiw I run 105 5800 11 speed (and have used the same set on 2 bikes a de rosa and my current 85 Miyata team). The team was aligned when I had a shop spread it to 130
shifting has been pretty much flawless.
I have more issues setting up the front and did find i needed to have the front cable really tight for the FD and really get the front parallel with the rings.
IIRC I had to have a far amount of tension on the rear cable at smallest cog
I have to replace cables soon so will soon do this again
shifting has been pretty much flawless.
I have more issues setting up the front and did find i needed to have the front cable really tight for the FD and really get the front parallel with the rings.
IIRC I had to have a far amount of tension on the rear cable at smallest cog
I have to replace cables soon so will soon do this again
__________________
Life is too short not to ride the best bike you have, as much as you can
(looking for Torpado Super light frame/fork or for Raleigh International frame fork 58cm)
Life is too short not to ride the best bike you have, as much as you can
(looking for Torpado Super light frame/fork or for Raleigh International frame fork 58cm)
Likes For squirtdad:
#11
Mother Nature's Son
Join Date: Mar 2016
Location: Sussex County, Delaware
Posts: 3,107
Bikes: 2014 Orbea Avant MD30, 2004 Airborne Zeppelin TI, 2003 Lemond Poprad, 2001 Lemond Tourmalet, 2014? Soma Smoothie
Mentioned: 15 Post(s)
Tagged: 0 Thread(s)
Quoted: 852 Post(s)
Liked 1,433 Times
in
815 Posts
I have a 7000 group set and have the same experience with the RD cable needing to be really tight when the chain is on the smallest cog. I seem to remember having an issue getting the front to shift correctly, if might have been needing tightness on the cable, but not sure. This is with exposed cabling. I have had it for a good while and it has worked really well the whole time.
Likes For delbiker1:
#12
Senior Member
Join Date: Sep 2017
Posts: 7,848
Mentioned: 38 Post(s)
Tagged: 0 Thread(s)
Quoted: 6939 Post(s)
Liked 10,944 Times
in
4,677 Posts
Likes For Koyote:
#13
Senior Member
Thread Starter
Join Date: Dec 2020
Location: Los Angeles
Posts: 917
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 445 Post(s)
Liked 1,040 Times
in
440 Posts
I run a 105 eleven speed on my gravel bike and I have two observations about shifting issues like this. The first is the derailleur spring seems a little weak and has been since new. The other is that the cable housing wear has an impact on shifting to higher gears. My housing sticks a little and combined with a weak spring to start with seems make shifting adjustments a bit touchy. Hope this helps.
Good call. It might not be the hanger, but that's a pretty good place to start. If it's ruled out, they can then look at the cables, B-tension, chain wrap, chain length, etc. The alternative is for you to futz around with all that stuff and still not solve the problem if the hanger is off.
Carrying a spare hanger is always a good idea. I wish manufacturers would supply one with their bikes.
Carrying a spare hanger is always a good idea. I wish manufacturers would supply one with their bikes.
I called my LBS and they said they can look at it. If the hanger is just slightly off they have a tool that can align it properly. I also removed the hanger to visually inspect it. If it's bent then it's definitely not something you can eyeball. The LBS said it could also just be a cross chaining issue with my setup, but on my 10 speed it can shift smoothly across the entire range with perfect gaps for each gear. Also I feel fairly confident in my road bike B-tension and chain length since I also built and tuned my gravel bike which shifts fine.
I'll first do the replacement inner tubing first (which it needs anyways) and if that doesn't solve it, I'll bring it to the LBS and also order the spare hanger for insurance! Thanks for the responses!
#14
Guest
Join Date: Sep 2020
Posts: 2,888
Mentioned: 13 Post(s)
Tagged: 0 Thread(s)
Quoted: 1346 Post(s)
Liked 3,270 Times
in
1,439 Posts
Best of luck, and let us know what happens!
Likes For Rolla:
#15
Senior Member
Join Date: Jul 2006
Location: San Jose (Willow Glen) Ca
Posts: 9,834
Bikes: Kirk Custom JK Special, '84 Team Miyata,(dura ace old school) 80?? SR Semi-Pro 600 Arabesque
Mentioned: 106 Post(s)
Tagged: 0 Thread(s)
Quoted: 2337 Post(s)
Liked 2,811 Times
in
1,535 Posts
hard when it is a steel bike hanger part of the drop out forging..... would need to carry spare dropout and a mini oxy/gas set
__________________
Life is too short not to ride the best bike you have, as much as you can
(looking for Torpado Super light frame/fork or for Raleigh International frame fork 58cm)
Life is too short not to ride the best bike you have, as much as you can
(looking for Torpado Super light frame/fork or for Raleigh International frame fork 58cm)
Likes For squirtdad:
#16
Method to My Madness
Join Date: Nov 2020
Location: Orange County, California
Posts: 3,641
Bikes: Trek FX 2, Cannondale Synapse, Cannondale CAAD4, Santa Cruz Stigmata GRX
Mentioned: 4 Post(s)
Tagged: 0 Thread(s)
Quoted: 1939 Post(s)
Liked 1,463 Times
in
1,012 Posts
#17
Guest
Join Date: Sep 2020
Posts: 2,888
Mentioned: 13 Post(s)
Tagged: 0 Thread(s)
Quoted: 1346 Post(s)
Liked 3,270 Times
in
1,439 Posts
Yep, I've had many bikes with built-in hangers. They're actually more durable than the replaceable ones, but you're SOL if they get bent or broken on a ride.
#18
Senior Member
Join Date: Jun 2002
Location: Montreal, Quebec
Posts: 5,921
Mentioned: 16 Post(s)
Tagged: 0 Thread(s)
Quoted: 1815 Post(s)
Liked 1,693 Times
in
974 Posts
Some do. Years ago I worked for a company which distributed Look frames. The frames were shipped with a spare derailleur hanger along with all the other hardware needed to build the bikes up
Likes For alcjphil:
#19
Senior Member
Thread Starter
Join Date: Dec 2020
Location: Los Angeles
Posts: 917
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 445 Post(s)
Liked 1,040 Times
in
440 Posts
So the jumping when you get to a certain cog, this happens at a different cog depending on whether you optimize shifting for the big cogs or the small cogs, right? And does this jump happen only on a down shift, only on an up shift, or on both? When did this start happening? Have you previously run the same components without any shifting issues?
Also I'm wondering if the issue could be with my 105 5800 rear shifter?
#20
Method to My Madness
Join Date: Nov 2020
Location: Orange County, California
Posts: 3,641
Bikes: Trek FX 2, Cannondale Synapse, Cannondale CAAD4, Santa Cruz Stigmata GRX
Mentioned: 4 Post(s)
Tagged: 0 Thread(s)
Quoted: 1939 Post(s)
Liked 1,463 Times
in
1,012 Posts
The RD-R7000 is Shimano's new(er) Shadow RD, which has a different profile than your RD-5800. Compare the respective locations and angles of the barrel adjusters in each rear derailleur. In the RD-5800, the barrel adjuster is located closer to the ground, and the shifter cable and housing enters the barrel adjuster at an angle roughly parallel to the ground. In the RD-R7000, barrel adjuster is located further to the ground, and the shifter cable and housing enters the barrel adjuster at a much steeper angle. If the shifter cable exits the frame at the junction of the right chain stay and right seat stay (like it does in my Cannondale Synapse), the housing forms a much, much tighter loop with a RD-R7000 than a RD-5800, which adversely impacts shifting. (That was why I had to return a RD-R8000 and search high and low for a RD-6800.)
#21
Senior Member
Join Date: Feb 2014
Location: Pasadena, CA
Posts: 4,848
Bikes: Schwinn Varsity
Mentioned: 22 Post(s)
Tagged: 0 Thread(s)
Quoted: 1931 Post(s)
Liked 742 Times
in
422 Posts
I called my LBS and they said they can look at it. If the hanger is just slightly off they have a tool that can align it properly. I also removed the hanger to visually inspect it. If it's bent then it's definitely not something you can eyeball. The LBS said it could also just be a cross chaining issue with my setup, but on my 10 speed it can shift smoothly across the entire range with perfect gaps for each gear. Also I feel fairly confident in my road bike B-tension and chain length since I also built and tuned my gravel bike which shifts fine.
#22
Senior Member
Thread Starter
Join Date: Dec 2020
Location: Los Angeles
Posts: 917
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 445 Post(s)
Liked 1,040 Times
in
440 Posts
Ah, now I know why.
No, the problem is with your new RD-R7000.
The RD-R7000 is Shimano's new(er) Shadow RD, which has a different profile than your RD-5800. Compare the respective locations and angles of the barrel adjusters in each rear derailleur. In the RD-5800, the barrel adjuster is located closer to the ground, and the shifter cable and housing enters the barrel adjuster at an angle roughly parallel to the ground. In the RD-R7000, barrel adjuster is located further to the ground, and the shifter cable and housing enters the barrel adjuster at a much steeper angle. If the shifter cable exits the frame at the junction of the right chain stay and right seat stay (like it does in my Cannondale Synapse), the housing forms a much, much tighter loop with a RD-R7000 than a RD-5800, which adversely impacts shifting. (That was why I had to return a RD-R8000 and search high and low for a RD-6800.)
No, the problem is with your new RD-R7000.
The RD-R7000 is Shimano's new(er) Shadow RD, which has a different profile than your RD-5800. Compare the respective locations and angles of the barrel adjusters in each rear derailleur. In the RD-5800, the barrel adjuster is located closer to the ground, and the shifter cable and housing enters the barrel adjuster at an angle roughly parallel to the ground. In the RD-R7000, barrel adjuster is located further to the ground, and the shifter cable and housing enters the barrel adjuster at a much steeper angle. If the shifter cable exits the frame at the junction of the right chain stay and right seat stay (like it does in my Cannondale Synapse), the housing forms a much, much tighter loop with a RD-R7000 than a RD-5800, which adversely impacts shifting. (That was why I had to return a RD-R8000 and search high and low for a RD-6800.)
Anyways I figure it's best I try an address the issue now since I do have another bike to fall back on. Also I won't know what the problem is until I bring it to the LBS, unless I do the tear down myself. I'm also probably going to order a new derailleur hanger just to be on the safe side. I'm not sure if I'll be able to find parts for this bike much longer, so it's probably best I just order a spare.
Last edited by jonathanf2; 05-09-22 at 10:21 AM.
#23
Method to My Madness
Join Date: Nov 2020
Location: Orange County, California
Posts: 3,641
Bikes: Trek FX 2, Cannondale Synapse, Cannondale CAAD4, Santa Cruz Stigmata GRX
Mentioned: 4 Post(s)
Tagged: 0 Thread(s)
Quoted: 1939 Post(s)
Liked 1,463 Times
in
1,012 Posts
I no longer use the 105 (CS-5800) 11-32 cassette which came with my road bike; you can have it if you want. I don't do as anywhere near as much climbing as the rest of you guys in the SoCal sub-forum. Although SoCal gas is so expensive nowadays that you can probably buy a 105 cassette with the roundtrip gas money.
Likes For SoSmellyAir:
#24
Senior Member
Thread Starter
Join Date: Dec 2020
Location: Los Angeles
Posts: 917
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 445 Post(s)
Liked 1,040 Times
in
440 Posts
In that case, do you have another 11 speed cassette to try?
I no longer use the 105 (CS-5800) 11-32 cassette which came with my road bike; you can have it if you want. I don't do as anywhere near as much climbing as the rest of you guys in the SoCal sub-forum. Although SoCal gas is so expensive nowadays that you can probably buy a 105 cassette with the roundtrip gas money.
I no longer use the 105 (CS-5800) 11-32 cassette which came with my road bike; you can have it if you want. I don't do as anywhere near as much climbing as the rest of you guys in the SoCal sub-forum. Although SoCal gas is so expensive nowadays that you can probably buy a 105 cassette with the roundtrip gas money.
#25
Senior Member
Thread Starter
Join Date: Dec 2020
Location: Los Angeles
Posts: 917
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 445 Post(s)
Liked 1,040 Times
in
440 Posts
The LBS called, they said the hanger was super bent! Wow, no way I would have noticed. Also they said my internal routing is a mess, so I'll just have them do everything in one go. They said everything should be 100% once they're done. Thanks for all the help everyone!
Likes For jonathanf2: