wheel question
#1
Senior Member
Thread Starter
Join Date: Nov 2014
Location: Saratoga calif.
Posts: 1,049
Bikes: Miyata 610(66cm), GT Vantara Hybrid (64cm), Nishiki International (64cm), Peugeot rat rod (62 cm), Trek 800 Burning Man helicopter bike, Bob Jackson frame (to be restored?) plus a never ending stream of neglected waifs from the Bike exchange.
Mentioned: 28 Post(s)
Tagged: 0 Thread(s)
Quoted: 339 Post(s)
Likes: 0
Liked 632 Times
in
229 Posts
wheel question
I have this wheel set that I want to use on a build.
One wheel needs to be trued but for the life of me I don't know how to proceed.
I have never seen this type before. How do you remove a spoke from this wheel and how adjust?
One wheel needs to be trued but for the life of me I don't know how to proceed.
I have never seen this type before. How do you remove a spoke from this wheel and how adjust?
#2
Senior Member
Join Date: Oct 2013
Location: Mich
Posts: 7,385
Bikes: RSO E-tire dropper fixie brifter
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 6 Post(s)
Liked 2,967 Times
in
1,916 Posts
remove the inner exposed wheel/rim strip. Then it should be self explanatory from there.
__________________
-Oh Hey!
-Oh Hey!
Likes For Troul:
#3
Senior Member
Join Date: Jan 2009
Location: San Diego, CA
Posts: 3,669
Mentioned: 10 Post(s)
Tagged: 0 Thread(s)
Quoted: 836 Post(s)
Liked 1,061 Times
in
745 Posts
Looks like it has nipples that just need unscrewing? (The wheel, not the dead body in the photo) and the spoke just pulls straight out of the hub.
EDIT: Just found this manual explaining truing for these wheels. TRICON Technical Manual_EN.book (dtswiss.com) Note that some of the Tricons have glued nipples that need to be heated before trying to turn. Fun.
EDIT: Just found this manual explaining truing for these wheels. TRICON Technical Manual_EN.book (dtswiss.com) Note that some of the Tricons have glued nipples that need to be heated before trying to turn. Fun.
Last edited by Crankycrank; 05-02-22 at 01:07 PM.
Likes For Crankycrank:
#4
Senior Member
Join Date: Dec 2020
Location: Wake Forest, NC
Posts: 5,784
Bikes: 1989 Cinelli Supercorsa
Mentioned: 11 Post(s)
Tagged: 0 Thread(s)
Quoted: 3505 Post(s)
Liked 2,924 Times
in
1,774 Posts
I think we need more info on the gold prone young lady.
Likes For Camilo:
#6
All Campy All The Time
Join Date: Nov 2013
Location: Richmond, Virginia
Posts: 1,417
Bikes: Listed in my signature.
Mentioned: 2 Post(s)
Tagged: 0 Thread(s)
Quoted: 177 Post(s)
Liked 114 Times
in
63 Posts
Note that there are no holes in the well of the rim for access to the spoke nipples. I've been told that the nipples are placed in through the valve stem hole and the you use a magnet to move each nipple to a spoke position. That makes a good airtight rim for a tubeless tire but a PIA for the wheelbuilder.
__________________
My C&V Bikes:
1972 Bottecchia Professional, 1972 Legnano Olympiade Record,
1982 Colnago Super, 1987 Bottecchia Team C-Record,
1988 Pinarello Montello, 1990 Masi Nuova Strada Super Record,
1995 Bianchi Campione d'Italia, 1995 DeBernardi Thron
My C&V Bikes:
1972 Bottecchia Professional, 1972 Legnano Olympiade Record,
1982 Colnago Super, 1987 Bottecchia Team C-Record,
1988 Pinarello Montello, 1990 Masi Nuova Strada Super Record,
1995 Bianchi Campione d'Italia, 1995 DeBernardi Thron
#7
working on my sandal tan
Join Date: Aug 2011
Location: CID
Posts: 22,629
Bikes: 1991 Bianchi Eros, 1964 Armstrong, 1988 Diamondback Ascent, 1988 Bianchi Premio, 1987 Bianchi Sport SX, 1980s Raleigh mixte (hers), All-City Space Horse (hers)
Mentioned: 98 Post(s)
Tagged: 0 Thread(s)
Quoted: 3871 Post(s)
Liked 2,568 Times
in
1,579 Posts
Likes For ThermionicScott:
#8
Senior Member
Join Date: Oct 2013
Location: Mich
Posts: 7,385
Bikes: RSO E-tire dropper fixie brifter
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 6 Post(s)
Liked 2,967 Times
in
1,916 Posts
Note that there are no holes in the well of the rim for access to the spoke nipples. I've been told that the nipples are placed in through the valve stem hole and the you use a magnet to move each nipple to a spoke position. That makes a good airtight rim for a tubeless tire but a PIA for the wheelbuilder.
__________________
-Oh Hey!
-Oh Hey!
#9
Senior Member
Join Date: Jan 2009
Location: San Diego, CA
Posts: 3,669
Mentioned: 10 Post(s)
Tagged: 0 Thread(s)
Quoted: 836 Post(s)
Liked 1,061 Times
in
745 Posts
Note that there are no holes in the well of the rim for access to the spoke nipples. I've been told that the nipples are placed in through the valve stem hole and the you use a magnet to move each nipple to a spoke position. That makes a good airtight rim for a tubeless tire but a PIA for the wheelbuilder.
#10
Senior Member
Thread Starter
Join Date: Nov 2014
Location: Saratoga calif.
Posts: 1,049
Bikes: Miyata 610(66cm), GT Vantara Hybrid (64cm), Nishiki International (64cm), Peugeot rat rod (62 cm), Trek 800 Burning Man helicopter bike, Bob Jackson frame (to be restored?) plus a never ending stream of neglected waifs from the Bike exchange.
Mentioned: 28 Post(s)
Tagged: 0 Thread(s)
Quoted: 339 Post(s)
Likes: 0
Liked 632 Times
in
229 Posts
These rims sound like a real PITA.
I will look at the instructions and see if I have the skills to true the wheel.
The deceased is Lola, one of my Burning Man "companions" From Cap'n Jonny's Outer Rim Tea Room.
The last few years were not kind to her and during a Spring storm she finally met her fate.
There was some crime scene tape but it blew away .
We are planning a service this summer..
I will look at the instructions and see if I have the skills to true the wheel.
The deceased is Lola, one of my Burning Man "companions" From Cap'n Jonny's Outer Rim Tea Room.
The last few years were not kind to her and during a Spring storm she finally met her fate.
There was some crime scene tape but it blew away .
We are planning a service this summer..
Likes For capnjonny:
#11
Senior Member
Join Date: Apr 2007
Posts: 6,760
Mentioned: 10 Post(s)
Tagged: 0 Thread(s)
Quoted: 1109 Post(s)
Liked 1,200 Times
in
760 Posts
Note that there are no holes in the well of the rim for access to the spoke nipples. I've been told that the nipples are placed in through the valve stem hole and the you use a magnet to move each nipple to a spoke position. That makes a good airtight rim for a tubeless tire but a PIA for the wheelbuilder.
#12
Senior Member
Join Date: Jun 2002
Location: Montreal, Quebec
Posts: 5,925
Mentioned: 16 Post(s)
Tagged: 0 Thread(s)
Quoted: 1819 Post(s)
Liked 1,693 Times
in
974 Posts
I don't know about these spoke nipples, but Campagnolo includes a small steel "spoke" that you screw into the nipple with their Shamal wheels so that you can use a magnet(also included) to fish a nipple through the rim when you replace a spoke
Likes For alcjphil:
#13
Method to My Madness
Join Date: Nov 2020
Location: Orange County, California
Posts: 3,648
Bikes: Trek FX 2, Cannondale Synapse, Cannondale CAAD4, Santa Cruz Stigmata GRX
Mentioned: 4 Post(s)
Tagged: 0 Thread(s)
Quoted: 1943 Post(s)
Liked 1,465 Times
in
1,014 Posts
#16
Senior Member
Thread Starter
Join Date: Nov 2014
Location: Saratoga calif.
Posts: 1,049
Bikes: Miyata 610(66cm), GT Vantara Hybrid (64cm), Nishiki International (64cm), Peugeot rat rod (62 cm), Trek 800 Burning Man helicopter bike, Bob Jackson frame (to be restored?) plus a never ending stream of neglected waifs from the Bike exchange.
Mentioned: 28 Post(s)
Tagged: 0 Thread(s)
Quoted: 339 Post(s)
Likes: 0
Liked 632 Times
in
229 Posts
I looked up the instructions for working on these wheels. What a crock. Give me an old school rim where I can easily true or replace spokes. These wheels seem to me to be just another example of mfgs. making things that no one except a high priced shop can work on. They may be trick but for us at the bike exchange, aren't worth the trouble. I am taking them back today and maybe we can sell them on E bay to some unsuspecting Rube who thinks that if your bike isn't made of carbon and has solar powered electronic everything on it it isn't worthy of sitting their privileged Butt on.
Steel is real.
Apologies to any unprivileged butts out there
Steel is real.
Apologies to any unprivileged butts out there
Likes For capnjonny:
#17
Senior Member
Thread Starter
Join Date: Nov 2014
Location: Saratoga calif.
Posts: 1,049
Bikes: Miyata 610(66cm), GT Vantara Hybrid (64cm), Nishiki International (64cm), Peugeot rat rod (62 cm), Trek 800 Burning Man helicopter bike, Bob Jackson frame (to be restored?) plus a never ending stream of neglected waifs from the Bike exchange.
Mentioned: 28 Post(s)
Tagged: 0 Thread(s)
Quoted: 339 Post(s)
Likes: 0
Liked 632 Times
in
229 Posts
Likes For capnjonny:
#18
Senior Member
I looked up the instructions for working on these wheels. What a crock. Give me an old school rim where I can easily true or replace spokes. These wheels seem to me to be just another example of mfgs. making things that no one except a high priced shop can work on. They may be trick but for us at the bike exchange, aren't worth the trouble. I am taking them back today and maybe we can sell them on E bay to some unsuspecting Rube who thinks that if your bike isn't made of carbon and has solar powered electronic everything on it it isn't worthy of sitting their privileged Butt on.
Steel is real.
Apologies to any unprivileged butts out there
Steel is real.
Apologies to any unprivileged butts out there