Headset "Click Stop?"
#1
Senior Member
Thread Starter
Join Date: Sep 2014
Location: Northeastern MA, USA
Posts: 1,678
Bikes: Garmin/Tacx Bike Smart
Mentioned: 3 Post(s)
Tagged: 0 Thread(s)
Quoted: 646 Post(s)
Liked 289 Times
in
191 Posts
Headset "Click Stop?"
I noticed today that my front wheel/headset has a "click stop" right about dead center. Rather than smoothly progressing across dead center when I turn the bars, there's a definite hitch right at the middle. What could cause this?
#2
Senior Member
Join Date: Dec 2019
Location: South Shore of Long Island
Posts: 2,785
Bikes: 2010 Carrera Volans, 2015 C-Dale Trail 2sl, 2017 Raleigh Rush Hour, 2017 Blue Proseccio, 1992 Giant Perigee, 80s Gitane Rallye Tandem
Mentioned: 12 Post(s)
Tagged: 0 Thread(s)
Quoted: 1079 Post(s)
Liked 1,017 Times
in
719 Posts
Your headset is indexed, it comes from general wear and tear. You can pull apart the headset and clean and grease the bearings and races which will make it better but the best solution is to replace it. Most modern frames use an integrated system with cartridge bearings set into the frame and the only real solution is to replace the bearings.
Likes For Russ Roth:
#3
Senior Member
Join Date: Jul 2013
Location: Nor-Cal
Posts: 3,767
Bikes: lots
Mentioned: 7 Post(s)
Tagged: 0 Thread(s)
Quoted: 1958 Post(s)
Liked 2,932 Times
in
1,489 Posts
It's wore out. As Russ posted it's time to replace it.
Likes For cxwrench:
#4
Junior Member
Join Date: Sep 2011
Location: San Juan, PR
Posts: 159
Bikes: 1980's Royce Union "fixed wheel", 1995 Trek 370, 406 -wheeled " shopper/minivelo"for running errands, SS Raleigh M60
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 43 Post(s)
Liked 58 Times
in
46 Posts
As said before, your headset is worn and the indexing described is called brinelling. Besides replacing (and if your headset is of the caged bearing design), you can: clean cups and races and see if besides the indentations of the bearings there is also heavy pitting ( if pitted, discard and replace headset). If only indented, you can replace the caged bearings with loose balls of the same size, filling the cup minus one ball. This should help for a couple more years depending on were you ride, as harsh conditions ("single tracking", mountain biking, randonneuring, etc.) will be more detrimental than road, leisure, bar hopping or light commuting to the headset.
#5
Senior Member
Join Date: Feb 2012
Location: Golden, CO and Tucson, AZ
Posts: 2,835
Bikes: 2016 Fuji Tread, 1983 Trek 520
Mentioned: 13 Post(s)
Tagged: 0 Thread(s)
Quoted: 674 Post(s)
Liked 738 Times
in
429 Posts
My "solution" to brinneling once was rotating cups 180 degrees.
Likes For andrewclaus:
#6
Old fart
Join Date: Nov 2004
Location: Appleton WI
Posts: 24,776
Bikes: Several, mostly not name brands.
Mentioned: 153 Post(s)
Tagged: 0 Thread(s)
Quoted: 3582 Post(s)
Liked 3,394 Times
in
1,928 Posts
Fretting damage from lubrication failure. The balls push grease away, and in the absence of significant rotation (as opposed to hubs, bottom brackets, etc., which are in continuous rotation), road shocks create microscopic welds between the lower cup and crown race, which are then torn out when the handlebar is turned. Over time, this creates pits that the balls will fall into, thus the "click-stop" you describe. The fix is headset replacement, although it's only the lower cup and crown race that get damaged. Ultimately, balls are not the best type of bearing for the thrust loads headsets must handle. Roller bearings are better suited for that purpose.
#7
Senior Member
As said before, your headset is worn and the indexing described is called brinelling. Besides replacing (and if your headset is of the caged bearing design), you can: clean cups and races and see if besides the indentations of the bearings there is also heavy pitting ( if pitted, discard and replace headset). If only indented, you can replace the caged bearings with loose balls of the same size, filling the cup minus one ball. This should help for a couple more years depending on were you ride, as harsh conditions ("single tracking", mountain biking, randonneuring, etc.) will be more detrimental than road, leisure, bar hopping or light commuting to the headset.
Replace the bearings.
Likes For davidad:
#8
Senior Member
Thread Starter
Join Date: Sep 2014
Location: Northeastern MA, USA
Posts: 1,678
Bikes: Garmin/Tacx Bike Smart
Mentioned: 3 Post(s)
Tagged: 0 Thread(s)
Quoted: 646 Post(s)
Liked 289 Times
in
191 Posts
Thanks, appreciate all the answers. I'll contact the LBS to see if I can get it done quickly.
Likes For dmanthree:
#9
Old fart
Join Date: Nov 2004
Location: Appleton WI
Posts: 24,776
Bikes: Several, mostly not name brands.
Mentioned: 153 Post(s)
Tagged: 0 Thread(s)
Quoted: 3582 Post(s)
Liked 3,394 Times
in
1,928 Posts
Another option that can buy you some time is to remove the crown race and re-install it in a different orientation so the pits no longer line up between the crown race and lower cup. This will minimize the "click-stop" effect until the fretting takes hold in the new orientation.