can't fix the chain - di2
#1
Junior Member
Thread Starter
Join Date: Dec 2021
Location: Montreal
Posts: 5
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 7 Post(s)
Likes: 0
Liked 3 Times
in
2 Posts
can't fix the chain - di2
Hello,
I have a r8050 set up with 11-28 sprocket and 52-36 chainring. When getting to 11-36, the chain is saggy (even on 10-36). When shifting to 52-28, I can barely shift: there is not enough chain.
I tried with a new longer chain to get to 52-28, but the saggy problem is worse. Not sure what am I missing here?! The b-screw at first helps with one problem, but increase the other problem later.
All parts are brand new.
Thank you for your help.
p.s. will post picture when the forum will allow me (now I can't).
I have a r8050 set up with 11-28 sprocket and 52-36 chainring. When getting to 11-36, the chain is saggy (even on 10-36). When shifting to 52-28, I can barely shift: there is not enough chain.
I tried with a new longer chain to get to 52-28, but the saggy problem is worse. Not sure what am I missing here?! The b-screw at first helps with one problem, but increase the other problem later.
All parts are brand new.
Thank you for your help.
p.s. will post picture when the forum will allow me (now I can't).
#2
Senior Member
Join Date: Oct 2013
Location: Mich
Posts: 7,386
Bikes: RSO E-tire dropper fixie brifter
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 6 Post(s)
Liked 2,968 Times
in
1,917 Posts
What rear derailleur is being used? Picture of the setup might be of some help.
52 36 seems a bit of a range for the cassette high & low.
52 36 seems a bit of a range for the cassette high & low.
__________________
-Oh Hey!
-Oh Hey!
#3
Old fart
Join Date: Nov 2004
Location: Appleton WI
Posts: 24,784
Bikes: Several, mostly not name brands.
Mentioned: 153 Post(s)
Tagged: 0 Thread(s)
Quoted: 3587 Post(s)
Liked 3,400 Times
in
1,934 Posts
You need a long cage derailleur to go with your longer chain.
Likes For JohnDThompson:
#4
Junior Member
Thread Starter
Join Date: Dec 2021
Location: Montreal
Posts: 5
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 7 Post(s)
Likes: 0
Liked 3 Times
in
2 Posts
i haven't installed the rear derailleur properly, it had to go a bit on an angle when being attached to the hanger. ... I just resolved it now (after 10+ hours of headache) ..but had to use a new, longer chain.
anyway, there is something I learned today.
anyway, there is something I learned today.
Likes For Cla250:
#7
Senior Member
Join Date: Jul 2013
Location: Nor-Cal
Posts: 3,767
Bikes: lots
Mentioned: 7 Post(s)
Tagged: 0 Thread(s)
Quoted: 1958 Post(s)
Liked 2,932 Times
in
1,489 Posts
You should be posting this in 'bicycle mechanics' not GD.
#9
Senior Member
Join Date: Jul 2013
Location: Nor-Cal
Posts: 3,767
Bikes: lots
Mentioned: 7 Post(s)
Tagged: 0 Thread(s)
Quoted: 1958 Post(s)
Liked 2,932 Times
in
1,489 Posts
Likes For cxwrench:
#10
Senior Member
Join Date: May 2010
Location: Bastrop Texas
Posts: 4,478
Bikes: Univega, Peu P6, Peu PR-10, Ted Williams, Peu UO-8, Peu UO-18 Mixte, Peu Dolomites
Mentioned: 13 Post(s)
Tagged: 0 Thread(s)
Quoted: 965 Post(s)
Liked 1,629 Times
in
1,045 Posts
Don't get too frustrated. These chain/derailleur problems get solved easy. Big gears in the back, greater than 28 teeth, need what is called a long cage derailluer. As soon as you post a picture of the Drive side of the bicycle we are kinda in the dark. Looking forward to solving this problem...
__________________
No matter where you're at... There you are... Δf:=f(1/2)-f(-1/2)
No matter where you're at... There you are... Δf:=f(1/2)-f(-1/2)
#11
Senior Member
Join Date: Jul 2013
Location: Nor-Cal
Posts: 3,767
Bikes: lots
Mentioned: 7 Post(s)
Tagged: 0 Thread(s)
Quoted: 1958 Post(s)
Liked 2,932 Times
in
1,489 Posts
Don't get too frustrated. These chain/derailleur problems get solved easy. Big gears in the back, greater than 28 teeth, need what is called a long cage derailluer. As soon as you post a picture of the Drive side of the bicycle we are kinda in the dark. Looking forward to solving this problem...
Likes For cxwrench:
#13
Old fart
Join Date: Nov 2004
Location: Appleton WI
Posts: 24,784
Bikes: Several, mostly not name brands.
Mentioned: 153 Post(s)
Tagged: 0 Thread(s)
Quoted: 3587 Post(s)
Liked 3,400 Times
in
1,934 Posts
But 52/36 in the front is a big jump. That's why the longer chain is needed, and the longer chain means the derailleur needs more chain-wrap capacity.
#14
Obsessed with Eddington
Join Date: Jun 2013
Location: Brussels (BE) 🇧🇪
Posts: 1,330
Bikes: '16 Spesh Diverge, '14 Spesh Fatboy, '18 Spesh Epic, '18 Spesh SL6, '21 Spesh SL7, '21 Spesh Diverge...and maybe n+1?
Mentioned: 2 Post(s)
Tagged: 0 Thread(s)
Quoted: 532 Post(s)
Liked 621 Times
in
368 Posts
Chain length is a function of the largest cog on the cassette and the big ring on the crankset. The RD cage size (short medium, long) is dictated by the largest cog on the cassette in conjunction with the total system capacity (determined by finding the tooth count differential on the crankset and adding it to the tooth count differential on the largest and smallest cog on the cassette).
You aren’t wrong, there’s just a couple of other factors at hand.
#15
don't try this at home.
Join Date: Jan 2006
Location: N. KY
Posts: 5,939
Mentioned: 10 Post(s)
Tagged: 0 Thread(s)
Quoted: 973 Post(s)
Liked 511 Times
in
351 Posts
My older short cage Ultegra 6870 came with 50/34 and 11-28. It works fine with an 11-32, even though the top pulley is quite close to the 32 cog.
I have about 28,000 miles on the groupset now, from Sept 2014. Everything still works perfectly, with fast, smooth shifts. I replaced the seatpost battery a few years ago when I started having to charge every 10 days or so. I'm kind of surprised that the buttons or the derailleurs haven't gotten worn or sloppy.
I have about 28,000 miles on the groupset now, from Sept 2014. Everything still works perfectly, with fast, smooth shifts. I replaced the seatpost battery a few years ago when I started having to charge every 10 days or so. I'm kind of surprised that the buttons or the derailleurs haven't gotten worn or sloppy.
#16
Senior Member
Join Date: Jul 2006
Location: Jacksonville, FL
Posts: 6,876
Bikes: Trek Domane SLR 7 AXS, Trek CheckPoint SL7 AXS, Trek Emonda ALR AXS, Trek FX 5 Sport
Mentioned: 2 Post(s)
Tagged: 0 Thread(s)
Quoted: 765 Post(s)
Liked 1,734 Times
in
1,010 Posts
That is the benefit of hanging onto any chain that you dont need when you have a new chain. You can push in a new pin and boom, longer chain without having to buy a new chain. I always have some on hand for this exact issue.
#17
Old fart
Join Date: Nov 2004
Location: Appleton WI
Posts: 24,784
Bikes: Several, mostly not name brands.
Mentioned: 153 Post(s)
Tagged: 0 Thread(s)
Quoted: 3587 Post(s)
Liked 3,400 Times
in
1,934 Posts
Chain length is a function of the largest cog on the cassette and the big ring on the crankset. The RD cage size (short medium, long) is dictated by the largest cog on the cassette in conjunction with the total system capacity
Last edited by JohnDThompson; 12-18-21 at 05:59 PM.
#18
Expired Member
Join Date: Jun 2007
Location: TN
Posts: 11,535
Mentioned: 37 Post(s)
Tagged: 0 Thread(s)
Quoted: 3670 Post(s)
Liked 5,422 Times
in
2,756 Posts
I know OP has resolved his problem but I'll throw this out for conversation. I'm using an 8000 group, 50-34, 11-34 and long cage RD. The chain is properly sized big/big and I don't think I could remove a link and still have movement in the derailleur. I've got chain sag in the small ring/ two smallest cogs, maybe three. Shimano says don't use those combos but stuff happens. Anyway, I was wondering if one of the RDs with a clutch would help. I figure not, since it's still the same chain wrap but maybe I'm missing something.
#19
Senior Member
Join Date: Jul 2013
Location: Nor-Cal
Posts: 3,767
Bikes: lots
Mentioned: 7 Post(s)
Tagged: 0 Thread(s)
Quoted: 1958 Post(s)
Liked 2,932 Times
in
1,489 Posts
FYI: that crankset differential is standard for Shimnao, and in general for 11-speed (until SRAM AXS). 50/34 and 53/39 are 16-tooth differential, also. As well as Praxis 48/32. Also, the new GRX cranksets use 46/30, and wait for it, 48/31 is the “wider” range crankset.
Chain length is a function of the largest cog on the cassette and the big ring on the crankset. The RD cage size (short medium, long) is dictated by the largest cog on the cassette in conjunction with the total system capacity (determined by finding the tooth count differential on the crankset and adding it to the tooth count differential on the largest and smallest cog on the cassette).
You aren’t wrong, there’s just a couple of other factors at hand.
Chain length is a function of the largest cog on the cassette and the big ring on the crankset. The RD cage size (short medium, long) is dictated by the largest cog on the cassette in conjunction with the total system capacity (determined by finding the tooth count differential on the crankset and adding it to the tooth count differential on the largest and smallest cog on the cassette).
You aren’t wrong, there’s just a couple of other factors at hand.
#20
Obsessed with Eddington
Join Date: Jun 2013
Location: Brussels (BE) 🇧🇪
Posts: 1,330
Bikes: '16 Spesh Diverge, '14 Spesh Fatboy, '18 Spesh Epic, '18 Spesh SL6, '21 Spesh SL7, '21 Spesh Diverge...and maybe n+1?
Mentioned: 2 Post(s)
Tagged: 0 Thread(s)
Quoted: 532 Post(s)
Liked 621 Times
in
368 Posts
#21
Obsessed with Eddington
Join Date: Jun 2013
Location: Brussels (BE) 🇧🇪
Posts: 1,330
Bikes: '16 Spesh Diverge, '14 Spesh Fatboy, '18 Spesh Epic, '18 Spesh SL6, '21 Spesh SL7, '21 Spesh Diverge...and maybe n+1?
Mentioned: 2 Post(s)
Tagged: 0 Thread(s)
Quoted: 532 Post(s)
Liked 621 Times
in
368 Posts
If the chain is too tight in the large-large combination, and sagging in the small-small combination, and a B-screw adjustment doesn't fix it, more chain wrap capacity (i.e. a longer cage on the rear derailleur) is the solution. Or changing the sprockets and/or chainrings to remain within the current derailleur's wrap capacity.
#22
Super Modest
Join Date: Jun 2002
Location: Central Illinois
Posts: 23,466
Bikes: Trek Emonda, Giant Propel, Colnago V3, Co-Motion Supremo, ICE VTX WC
Mentioned: 107 Post(s)
Tagged: 1 Thread(s)
Quoted: 10963 Post(s)
Liked 4,620 Times
in
2,123 Posts
#23
Senior Member
Join Date: Sep 2017
Posts: 7,877
Mentioned: 38 Post(s)
Tagged: 0 Thread(s)
Quoted: 6963 Post(s)
Liked 10,962 Times
in
4,688 Posts
#24
Senior Member
Join Date: Jul 2013
Location: Nor-Cal
Posts: 3,767
Bikes: lots
Mentioned: 7 Post(s)
Tagged: 0 Thread(s)
Quoted: 1958 Post(s)
Liked 2,932 Times
in
1,489 Posts
Stop posting stuff like this. ALL modern drivetrains are designed to go big/big. It might make for a tiny bit extra wear but it's fine to do for short periods of time.