Brompton Tensioner Chain Keeper
#1
Senior Member
Thread Starter
Join Date: Sep 2005
Location: Michigan
Posts: 3,706
Bikes: Trek 730 (quad), 720 & 830, Bike Friday NWT, Brompton M36R & M6R, Dahon HAT060 & HT060, ...
Mentioned: 10 Post(s)
Tagged: 0 Thread(s)
Quoted: 840 Post(s)
Liked 336 Times
in
251 Posts
Brompton Tensioner Chain Keeper
When debris gets in-between Brompton's chain and tensioner pulley, the chain routinely liberates itself. For me this has been a problem in winter, with the tensioner orienting itself low due to a front derailleur, and snow inducing the chain drop. It seems that I managed to solve the problem by building up a chain keeper around the derailleur pulley, extending the bolt on which the pulley mounts and adding a short alu bar with another bolt + stainless tube such as for the pulley axle. I vigorously rode into piled up last remnants of snow around our area and the chain stayed put. I also experimented letting cloth work itself in-between the chain and pulley and the chain stayed put, unlike without the keeper.
Likes For 2_i:
#2
Senior Member
Join Date: Aug 2014
Location: UK
Posts: 737
Bikes: Dahon Jetstream p8 (sold), customized Dahon Helios x10, customzed Dahon Smooth Hound x11,customized Dahon Hammerhead 8.0 d7, Planet X Free Ranger (mullet setup 1x11), Planet X Giovanissimi 20 (1x9), Frog 52 (1x9) and Frog 48 1s
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 264 Post(s)
Liked 238 Times
in
174 Posts
nice job!
Likes For Fentuz:
#3
Newbie
Join Date: May 2007
Posts: 32
Mentioned: 1 Post(s)
Tagged: 0 Thread(s)
Quoted: 8 Post(s)
Likes: 0
Liked 9 Times
in
7 Posts
Could it also be that the tension is on the low side when you use the small chainwheel? I was able to increase the tension of the chain tensioner by putting more tension on the spring.
Last edited by biker101; 04-12-22 at 07:59 PM. Reason: removed pics
#4
Senior Member
Thread Starter
Join Date: Sep 2005
Location: Michigan
Posts: 3,706
Bikes: Trek 730 (quad), 720 & 830, Bike Friday NWT, Brompton M36R & M6R, Dahon HAT060 & HT060, ...
Mentioned: 10 Post(s)
Tagged: 0 Thread(s)
Quoted: 840 Post(s)
Liked 336 Times
in
251 Posts
I wonder how did you increase the tension in your case?
#6
Newbie
Join Date: May 2007
Posts: 32
Mentioned: 1 Post(s)
Tagged: 0 Thread(s)
Quoted: 8 Post(s)
Likes: 0
Liked 9 Times
in
7 Posts
As I now have a quantitative assessment of the tension, it drops by just 25% for the tensioner arm in the 6 o'clock position, compared to the 3 o'clock, this for no modifications of any sort done to the tensioner. Certainly more tension would be helping with the snow, but any reasonably increased tension would presumably get overwhelmed by sufficiently sticky, dense snow packing the tensioner wheel. In any case, I now have both that chain keeper and increased tension compared to the original. So far, shifting seems to be more often smoother with the increased tension, than deteriorated - no obvious negatives yet of the increase.
I wonder how did you increase the tension in your case?
I wonder how did you increase the tension in your case?
#7
Senior Member
Thread Starter
Join Date: Sep 2005
Location: Michigan
Posts: 3,706
Bikes: Trek 730 (quad), 720 & 830, Bike Friday NWT, Brompton M36R & M6R, Dahon HAT060 & HT060, ...
Mentioned: 10 Post(s)
Tagged: 0 Thread(s)
Quoted: 840 Post(s)
Liked 336 Times
in
251 Posts
Are you riding with that increase in the tension? Is the tensioner holding up fine? In my count, the modification you discuss increases the tension at the 3 o'clock position by extra 100% over the original. I was scared that this kind of increase could destroy the plastic tensioner. I did what you describe, but starting with a weaker spring than the original one, so I ended up with the tension at the 3 o'clock higher by only 30% over the original.
Last edited by 2_i; 04-18-22 at 09:20 PM. Reason: Percentage fixed
#8
Newbie
Join Date: May 2007
Posts: 32
Mentioned: 1 Post(s)
Tagged: 0 Thread(s)
Quoted: 8 Post(s)
Likes: 0
Liked 9 Times
in
7 Posts
Are you riding with that increase in the tension? Is the tensioner holding up fine? In my count, the modification you discuss increases the tension at the 3 o'clock position by extra 100% over the original. I was scared that this kind of increase could destroy the plastic tensioner. I did what you describe, but starting with a weaker spring than the original one, so I ended up with the tension at the 3 o'clock higher by only 30% over the original.