Go Back  Bike Forums > Bike Forums > General Cycling Discussion
Reload this Page >

Please help me understand how stem length affects steering

Notices
General Cycling Discussion Have a cycling related question or comment that doesn't fit in one of the other specialty forums? Drop on in and post in here! When possible, please select the forum above that most fits your post!

Please help me understand how stem length affects steering

Old 06-21-21, 11:04 AM
  #1  
VicBC_Biker
Senior Member
Thread Starter
 
Join Date: May 2021
Posts: 219
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 111 Post(s)
Liked 69 Times in 51 Posts
Please help me understand how stem length affects steering

I've been experimenting with differen stem lengths to try to find a good riding position on my bike.

Online, I read that shorter stems cause 'twitchy' (or even in one video 'terrifying') steering response and handling.

I haven't noticed much difference, and I don't understand why stem length should affect steering response.

Imagine bolting a piece of plywood to the top of the steerer tube.




If I'm pushing at the edge of the plywood, it doesn't matter whether I grab spot A,B, or C - the board will rotate the same number of degrees and the fork/wheel will turn the same amount.

Longer bars grabbed at the ends will result in 'less sensitive' steering, and the really short bar used on some hour record bikes will make the steering more responsive.


Similarily, my hands on the 'tops' nearer the middle make steering more 'twitchy'.

But stem length? I don't understand.

Last edited by VicBC_Biker; 06-21-21 at 11:05 AM. Reason: typos
VicBC_Biker is offline  
Old 06-21-21, 11:10 AM
  #2  
unterhausen
Randomhead
 
Join Date: Aug 2008
Location: Happy Valley, Pennsylvania
Posts: 24,364
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 4 Post(s)
Liked 3,664 Times in 2,497 Posts
It has barely any effect all the way down to zero length. I once told a 'bent rider that their idea of a zero length stem was a bad idea, and then decided to draw a free body diagram and check. It takes extreme steering angles to affect the forces on the fork.
Of course, not even mechanical engineering undergrads know how to draw or interpret a free body diagram anymore, so it's always a waste to tell people this.
unterhausen is offline  
Likes For unterhausen:
Old 06-21-21, 01:29 PM
  #3  
Pop N Wood
Senior Member
 
Join Date: Jun 2020
Location: Maryland
Posts: 1,379

Bikes: 1982 Bianchi Sport SX, Rayleigh Tamland 1, Rans V-Rex recumbent, Fuji MTB, 80's Cannondale MTB with BBSHD ebike motor

Mentioned: 1 Post(s)
Tagged: 0 Thread(s)
Quoted: 667 Post(s)
Liked 529 Times in 355 Posts
Originally Posted by VicBC_Biker
If I'm pushing at the edge of the plywood, it doesn't matter whether I grab spot A,B, or C - the board will rotate the same number of degrees and the fork/wheel will turn the same amount.
Well, technically yes but no not really. You don't really move your hands a set number of degrees, you move them some distance. Hands in the A position are a greater radius from the stem axis, thus they need to move farther (a larger arc radius) to turn the stem a certain number of degrees.

What is super important to note is with your hands in the B position any side to side pressure from your hands will not turn the bars. As a guy who switched out his drop bars for a set of LONG bullhorns is it pretty easy to pull side to side, especially when out of the saddle and pulling on the bars. I had to practically relearn how to ride when I went to the bullhorns. I have to be super deliberate with my hands or I can easily take myself down.

So while getting your hands a greater radius from the stem axis should in theory make the bike less sensitive to sloppy hand movement, I think it is the side to side leverage from having them way out front that makes the bike feel "twitchy". When you think about it most people ride on the top corners of their drops, which is near position B on your diagram.
Pop N Wood is offline  
Likes For Pop N Wood:
Old 06-21-21, 01:43 PM
  #4  
prj71
Senior Member
 
Join Date: Jun 2015
Location: North Central Wisconsin
Posts: 4,601
Mentioned: 14 Post(s)
Tagged: 0 Thread(s)
Quoted: 2965 Post(s)
Liked 1,167 Times in 763 Posts
I have to wonder these days if people have forgotten how to use google?

https://cyclingtips.com/2015/03/how-...-and-handling/

https://www.cyclist.co.uk/in-depth/4...-1-stem-length
prj71 is offline  
Likes For prj71:
Old 06-21-21, 01:43 PM
  #5  
VicBC_Biker
Senior Member
Thread Starter
 
Join Date: May 2021
Posts: 219
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 111 Post(s)
Liked 69 Times in 51 Posts
I should have drawn the sketch a bit better:


Hands in position 'A' correspond to hand position on drop bars (on the hoods/tops/drops) with a 'normal' (90-120 mm ??) length stem.

Hands in position 'B' would be a 'zero' stem.

Most of the online explanations focus on the stem length, not any curve in the bars.
VicBC_Biker is offline  
Old 06-21-21, 01:44 PM
  #6  
VicBC_Biker
Senior Member
Thread Starter
 
Join Date: May 2021
Posts: 219
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 111 Post(s)
Liked 69 Times in 51 Posts
Originally Posted by prj71
I have to wonder these days if people have forgotten how to use google?

https://cyclingtips.com/2015/03/how-...-and-handling/

https://www.cyclist.co.uk/in-depth/4...-1-stem-length
Yes, if it is on the internet, it must be correct.
VicBC_Biker is offline  
Likes For VicBC_Biker:
Old 06-21-21, 01:46 PM
  #7  
Rolla
Guest
 
Join Date: Sep 2020
Posts: 2,888
Mentioned: 13 Post(s)
Tagged: 0 Thread(s)
Quoted: 1346 Post(s)
Liked 3,269 Times in 1,439 Posts
I don't think stem length affects steering enough to notice much, but it does affect weight distribution, and that can make a bike feel like it's steering differently.

I'd say trail and rake have a greater effect on steering than stem length.
Rolla is offline  
Likes For Rolla:
Old 06-21-21, 01:49 PM
  #8  
VicBC_Biker
Senior Member
Thread Starter
 
Join Date: May 2021
Posts: 219
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 111 Post(s)
Liked 69 Times in 51 Posts
Originally Posted by Pop N Wood
So while getting your hands a greater radius from the stem axis should in theory make the bike less sensitive to sloppy hand movement, I think it is the side to side leverage from having them way out front that makes the bike feel "twitchy". When you think about it most people ride on the top corners of their drops, which is near position B on your diagram.
I didn't draw the diagram well...please see my 2nd attempt.
Riding on a standard bar setup is like position 'A' - out front.
Riding on an absolutely 'zero-length' stem would be like position 'B' - and that is supposed to be twitchy/terrifying, etc etc
VicBC_Biker is offline  
Old 06-21-21, 01:54 PM
  #9  
VicBC_Biker
Senior Member
Thread Starter
 
Join Date: May 2021
Posts: 219
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 111 Post(s)
Liked 69 Times in 51 Posts
Originally Posted by Rolla
I don't think stem length affects steering enough to notice much, but it does affect weight distribution, and that can make a bike feel like it's steering differently..
That's my impression as well - a shorter stem can move weight off my hands and make the steering feel less 'solid'.

Originally Posted by Rolla
I'd say trail and rake have a greater effect on steering than stem length.
Yes. Bike geometry definitely makes a difference.
I don't have much experience with a lot of different bikes but some feel like they 'steer themselves' and tempt me to ride 'no hands' while others are warning me to pay attention.
VicBC_Biker is offline  
Likes For VicBC_Biker:
Old 06-21-21, 01:59 PM
  #10  
Rolla
Guest
 
Join Date: Sep 2020
Posts: 2,888
Mentioned: 13 Post(s)
Tagged: 0 Thread(s)
Quoted: 1346 Post(s)
Liked 3,269 Times in 1,439 Posts
Article about zero-length stems and the general handling characteristics of various length stems and bar widths, which are related:

https://www.cyclingabout.com/steerin...teering-speed/

The short version: "If you switch from a 50mm-to-0mm stem, you’ll probably not notice any twitchiness difference using a flat or riser bar, but you will notice the extra twitchiness with narrower drop bars."
Rolla is offline  
Likes For Rolla:
Old 06-21-21, 02:05 PM
  #11  
bOsscO
bOsscO
 
bOsscO's Avatar
 
Join Date: May 2006
Location: Vancouver
Posts: 748

Bikes: 2015 Norco Search S1, 93 Mongoose IBOC COMP

Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 293 Post(s)
Liked 353 Times in 211 Posts
Originally Posted by VicBC_Biker
Yes, if it is on the internet, it must be correct.
Says the guy asking questions...on the internet.
I'm not trying to be critical here, but did you read the two pieces in the links? Do they make sense to you?
bOsscO is offline  
Old 06-21-21, 02:07 PM
  #12  
cxwrench
Senior Member
 
cxwrench's Avatar
 
Join Date: Jul 2013
Location: Nor-Cal
Posts: 3,767

Bikes: lots

Mentioned: 7 Post(s)
Tagged: 0 Thread(s)
Quoted: 1958 Post(s)
Liked 2,932 Times in 1,489 Posts
Originally Posted by Rolla
I don't think stem length affects steering enough to notice much, but it does affect weight distribution, and that can make a bike feel like it's steering differently.

I'd say trail and rake have a greater effect on steering than stem length.
It's actually head angle and offset (rake)...those 2 numbers result in a specific amount of trail. I'm glad everyone in this thread seems to understand what is really happening. Changing stem length doesn't change how a bike turns, that is soley determined by geometry mentioned previously (head angle and rake). Just as you say weight distribution changes how the bike feels, but not how it turns.
cxwrench is offline  
Likes For cxwrench:
Old 06-21-21, 02:07 PM
  #13  
terrymorse 
climber has-been
 
terrymorse's Avatar
 
Join Date: Dec 2004
Location: Palo Alto, CA
Posts: 7,007

Bikes: Scott Addict R1, Felt Z1

Mentioned: 10 Post(s)
Tagged: 0 Thread(s)
Quoted: 3342 Post(s)
Liked 3,443 Times in 1,741 Posts
Only hand position matters, which is determined by a combination of the bars and stem.

1. With hand position in line with the steering tube, hand movements are purely front and back. This is the position where a unit of hand movement has the greatest steering input.

2. As hand position moves in front of the steering tube, steering inputs grow more side to side, and the radius from steering tube to hand increases. Therefore, a unit of hand movement produces decreasing steering input.

3. Inputs grow side to side with hands behind the steering tube, but in the opposite direction.

For most people, 1 feels twitchy, 2 feels stable, 3 feels weird.
__________________
Ride, Rest, Repeat. ROUVY: terrymorse



Last edited by terrymorse; 06-21-21 at 03:35 PM.
terrymorse is offline  
Likes For terrymorse:
Old 06-21-21, 02:11 PM
  #14  
prj71
Senior Member
 
Join Date: Jun 2015
Location: North Central Wisconsin
Posts: 4,601
Mentioned: 14 Post(s)
Tagged: 0 Thread(s)
Quoted: 2965 Post(s)
Liked 1,167 Times in 763 Posts
Originally Posted by VicBC_Biker
Yes, if it is on the internet, it must be correct.
Point out what's incorrect in the two articles I posted.
prj71 is offline  
Old 06-21-21, 02:24 PM
  #15  
Trakhak
Senior Member
 
Trakhak's Avatar
 
Join Date: Jan 2005
Location: Baltimore, MD
Posts: 5,340
Mentioned: 15 Post(s)
Tagged: 0 Thread(s)
Quoted: 2430 Post(s)
Liked 2,889 Times in 1,646 Posts
As I've always understood it, the points raised above with regard to bike handling/stem length apply only to very low speeds. Above that speed range, you aim the bike by leaning, not steering. Twitchy/scary handling is a consequence of your front/back weight distribution being less than ideal. (Further, it's my understanding that professional bike fitters recommend stem lengths on the basis of front/back weight distribution, not handling characteristics.)
Trakhak is online now  
Likes For Trakhak:
Old 06-21-21, 02:33 PM
  #16  
VicBC_Biker
Senior Member
Thread Starter
 
Join Date: May 2021
Posts: 219
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 111 Post(s)
Liked 69 Times in 51 Posts
Originally Posted by Rolla
Article about zero-length stems and the general handling characteristics of various length stems and bar widths, which are related:

https://www.cyclingabout.com/steerin...teering-speed/
Thanks, Rolla

Here's a diagram from that article:

Notice the misrepresentations?
VicBC_Biker is offline  
Likes For VicBC_Biker:
Old 06-21-21, 02:46 PM
  #17  
VicBC_Biker
Senior Member
Thread Starter
 
Join Date: May 2021
Posts: 219
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 111 Post(s)
Liked 69 Times in 51 Posts
Originally Posted by bOsscO
Says the guy asking questions...on the internet.
I'm not trying to be critical here, but did you read the two pieces in the links? Do they make sense to you?
For me, there is a huge difference between personal experiences of people who respond in (good) online forums, and internet articles and videos which are primarily designed to generate clicks and ad revenue.
The latter often simply repeat material from other sites and articles, which may or may not be accurate and well thought-out. It's not unusual for 'long held' beliefs and ideas to be wrong.
I have read quite a few articles online and watched videos like the one from GCN on YouTube.
They didn't correspond with my experience in fitting a minimum length (35 mm center-to-center) stem to my road bike.
So I was wondering if other people here had had similar experiences, or could explain to me why my ideas were wrong.

I appreciate all the info I've gotten here.
VicBC_Biker is offline  
Old 06-21-21, 02:55 PM
  #18  
Gresp15C
Senior Member
 
Gresp15C's Avatar
 
Join Date: Sep 2014
Posts: 3,893
Mentioned: 20 Post(s)
Tagged: 0 Thread(s)
Quoted: 1062 Post(s)
Liked 665 Times in 421 Posts
My bikes with swept bars have hand positions ranging from in-line with the steering axis, to about 2 inches behind the steering axis. It doesn't seem to affect handling at all.

But it can potentially affect braking, something that I'm always conscious of. During braking, more of your weight shifts to your hands, and having your hands further forward gives you better control of the bike and less chance of going over the bar.
Gresp15C is offline  
Likes For Gresp15C:
Old 06-21-21, 03:45 PM
  #19  
csport
Senior Member
 
Join Date: Sep 2015
Location: /dev/null
Posts: 673

Bikes: Soma Double Cross Disc (2017), red Hardrock FS (circa 1996)

Mentioned: 5 Post(s)
Tagged: 0 Thread(s)
Quoted: 215 Post(s)
Liked 153 Times in 101 Posts
Originally Posted by Pop N Wood
What is super important to note is with your hands in the B position any side to side pressure from your hands will not turn the bars. As a guy who switched out his drop bars for a set of LONG bullhorns is it pretty easy to pull side to side, especially when out of the saddle and pulling on the bars. I had to practically relearn how to ride when I went to the bullhorns. I have to be super deliberate with my hands or I can easily take myself down.

So while getting your hands a greater radius from the stem axis should in theory make the bike less sensitive to sloppy hand movement, I think it is the side to side leverage from having them way out front that makes the bike feel "twitchy". When you think about it most people ride on the top corners of their drops, which is near position B on your diagram.

An example of a configuration extremely sensitive to such side to side pressure is aero bars.
csport is offline  
Likes For csport:
Old 06-21-21, 03:59 PM
  #20  
VicBC_Biker
Senior Member
Thread Starter
 
Join Date: May 2021
Posts: 219
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 111 Post(s)
Liked 69 Times in 51 Posts
As I'm sometimes math-challenged, I went down to the shop and built a (full-scale) model.



I made measurements for three different turns: 7.5 degrees, 15 degrees. and 30 degrees.
As @Trakhak mentions, the larger (degree) turns will only be made at very slow speeds.

The imagined hand position was at the hoods, and movement was measured at an imagined vertical line at the forward curve of the bars.

The model stem lengths were 25mm C-C and 100 mm C-C. 25mm is less than any real stem length could be, with normal steerer tubes and bar sizes.

It IS correct that with the longer stem, more movement at the ends of the bar is required for the same rotation of the steerer tube, compared to a short stem.
For a 7.5 degree turn, the longer stem setup will require my hands to move approximately) 40 mm (along an arc), the shorter stem 25 mm. For a 30 degree turn the longer stem will require a hand movement of 155 mm, the shorter stem 115 mm.

The longer stem will require more hand movement, and should seem 'less sensitive'.

So my initial thoughts and conceptual model were incorrect.

Either I adapt to different setups very quickly, or I'm not skilled enough to notice the difference with different stems.
VicBC_Biker is offline  
Likes For VicBC_Biker:
Old 06-21-21, 04:00 PM
  #21  
VicBC_Biker
Senior Member
Thread Starter
 
Join Date: May 2021
Posts: 219
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 111 Post(s)
Liked 69 Times in 51 Posts
Originally Posted by terrymorse
Only hand position matters, which is determined by a combination of the bars and stem.

1. With hand position in line with the steering tube, hand movements are purely front and back. This is the position where a unit of hand movement has the greatest steering input.

2. As hand position moves in front of the steering tube, steering inputs grow more side to side, and the radius from steering tube to hand increases. Therefore, a unit of hand movement produces decreasing steering input.
Thanks - very clear.
​​​​​​​I agree.
VicBC_Biker is offline  
Likes For VicBC_Biker:
Old 06-21-21, 04:26 PM
  #22  
Gresp15C
Senior Member
 
Gresp15C's Avatar
 
Join Date: Sep 2014
Posts: 3,893
Mentioned: 20 Post(s)
Tagged: 0 Thread(s)
Quoted: 1062 Post(s)
Liked 665 Times in 421 Posts
My thought about "steering input" is that any cyclist is strong enough to produce vastly more steering input than can be used without crashing, when riding under normal pavement conditions. We can, and must, apply a limited and varying amount of torque to the steering axle, that also depends on speed and other conditions. So we're already adapting, or we'd be dead. Now the handlebar is doing other things for us. It helps us to stabilize our own body position relative to the bike, and to manage the weight distribution between the front and back wheels. Those things all have to do with control of the bike.
Gresp15C is offline  
Likes For Gresp15C:
Old 06-21-21, 04:34 PM
  #23  
Pop N Wood
Senior Member
 
Join Date: Jun 2020
Location: Maryland
Posts: 1,379

Bikes: 1982 Bianchi Sport SX, Rayleigh Tamland 1, Rans V-Rex recumbent, Fuji MTB, 80's Cannondale MTB with BBSHD ebike motor

Mentioned: 1 Post(s)
Tagged: 0 Thread(s)
Quoted: 667 Post(s)
Liked 529 Times in 355 Posts
Originally Posted by VicBC_Biker
I didn't draw the diagram well...please see my 2nd attempt.
Riding on a standard bar setup is like position 'A' - out front.
Riding on an absolutely 'zero-length' stem would be like position 'B' - and that is supposed to be twitchy/terrifying, etc etc
I interpreted your drawing the way you intended.

I guess my experience is the opposite of what you are saying, i.e. getting the grips farther forward makes the bike more sensitive to improper steering input.

I put a riser bar and Jones H bar on one of my bikes to turn it into an upright cruiser. The bars are probably in line with the stem. Super stable bike.
Pop N Wood is offline  
Likes For Pop N Wood:
Old 06-21-21, 04:40 PM
  #24  
Pop N Wood
Senior Member
 
Join Date: Jun 2020
Location: Maryland
Posts: 1,379

Bikes: 1982 Bianchi Sport SX, Rayleigh Tamland 1, Rans V-Rex recumbent, Fuji MTB, 80's Cannondale MTB with BBSHD ebike motor

Mentioned: 1 Post(s)
Tagged: 0 Thread(s)
Quoted: 667 Post(s)
Liked 529 Times in 355 Posts
Originally Posted by csport

An example of a configuration extremely sensitive to such side to side pressure is aero bars.
Exactly.

Except with the bullhorns putting the hands so far apart it must feel different. IDK, do people come out of the saddle and pump with their arms while on the aero bars?

I'm telling you the first few times I rode the bike I almost dumped it. Maybe things go non-linear once you get too far forward.

I can also tell you with a recumbent one needs to be very conscious of the "tiller effect". Takes some practice to get just the right touch. When I first learned to ride that thing I held the bars up so they rotated directly in line with the steerer tube. Made the bike much less twitchy.

Maybe I am just the outlier.

Last edited by Pop N Wood; 06-21-21 at 04:43 PM.
Pop N Wood is offline  
Likes For Pop N Wood:
Old 06-21-21, 05:17 PM
  #25  
VicBC_Biker
Senior Member
Thread Starter
 
Join Date: May 2021
Posts: 219
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 111 Post(s)
Liked 69 Times in 51 Posts
Originally Posted by Pop N Wood
I interpreted your drawing the way you intended.

I guess my experience is the opposite of what you are saying, i.e. getting the grips farther forward makes the bike more sensitive to improper steering input.

I put a riser bar and Jones H bar on one of my bikes to turn it into an upright cruiser. The bars are probably in line with the stem. Super stable bike.
It's complicated! (As Gresp15C points out..)
For instance...
I've read in many places that hands in the drops is the most stable and controlled position, but because I'm not in great cycling shape, I don't feel very comfortable or agile when my hands are in the drops.

A
VicBC_Biker is offline  
Likes For VicBC_Biker:

Thread Tools
Search this Thread

Contact Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service -

Copyright © 2024 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.