Are my 3 speed cottered cranks bent?
#1
Junior Member
Thread Starter
Join Date: Aug 2014
Posts: 119
Mentioned: 1 Post(s)
Tagged: 0 Thread(s)
Quoted: 63 Post(s)
Liked 28 Times
in
18 Posts
Are my 3 speed cottered cranks bent?
I've noticed an odd lopsided feeling when I pedal my Armstrong 3 speed. It feels almost as if the cranks are bent or the pedals are bent. Or perhaps it's something inside the bottom bracket? I'd be grateful for any thoughts or opinions. Thank you!
#2
Senior Member
Join Date: Jan 2009
Location: San Diego, CA
Posts: 3,672
Mentioned: 10 Post(s)
Tagged: 0 Thread(s)
Quoted: 836 Post(s)
Liked 1,061 Times
in
745 Posts
It LOOKS like the left crank is bent inwards from the angle of the pedal but always hard to tell if there is any optical distortion from photos. If so an old steel crank like that can be bent back. A good sturdy vice and a cheater bar with the crank/pedal removed will make it much easier.
Likes For Crankycrank:
#3
Senior Member
Join Date: Feb 2012
Location: Golden, CO and Tucson, AZ
Posts: 2,837
Bikes: 2016 Fuji Tread, 1983 Trek 520
Mentioned: 13 Post(s)
Tagged: 0 Thread(s)
Quoted: 676 Post(s)
Liked 741 Times
in
430 Posts
Try "new" pedals first. You'll probably need 1/2" spindles.
A pedal spindle will bend well before those steel cranks will, and will give the wobbly sensation in the feet.
A pedal spindle will bend well before those steel cranks will, and will give the wobbly sensation in the feet.
Likes For andrewclaus:
#4
Senior Member
Join Date: Feb 2012
Location: Rochester, NY
Posts: 18,081
Bikes: Stewart S&S coupled sport tourer, Stewart Sunday light, Stewart Commuting, Stewart Touring, Co Motion Tandem, Stewart 3-Spd, Stewart Track, Fuji Finest, Mongoose Tomac ATB, GT Bravado ATB, JCP Folder, Stewart 650B ATB
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 4204 Post(s)
Liked 3,861 Times
in
2,309 Posts
Generally 1/2" pedal threads are for 1 piece cranks. These 3 piece cranks will most likely have a 9/16" pedal thread. I do agree that either the LH arm is bent, the LH pedal axle is bent or the camera lens is distorting things. Nice bike BTW. Andy
__________________
AndrewRStewart
AndrewRStewart
Likes For Andrew R Stewart:
#5
Senior Member
Join Date: May 2010
Location: Bastrop Texas
Posts: 4,479
Bikes: Univega, Peu P6, Peu PR-10, Ted Williams, Peu UO-8, Peu UO-18 Mixte, Peu Dolomites
Mentioned: 13 Post(s)
Tagged: 0 Thread(s)
Quoted: 966 Post(s)
Liked 1,629 Times
in
1,045 Posts
I have seen a few cottered cranks that were off a little bit in thier alignment. It was not much, no more than 2°. I was converting them over to a square tapper spindle and on close inspection of the old spindles I noted that the face of the spindle where it engages the pin was well worn. I think that the cotter had become loose and worn out the face. Then when repairing with a new pin the crank arm was off a little in the direction of the wear.
__________________
No matter where you're at... There you are... Δf:=f(1/2)-f(-1/2)
No matter where you're at... There you are... Δf:=f(1/2)-f(-1/2)
Likes For zandoval:
#6
Happy With My Bikes
Join Date: Sep 2020
Location: Oklahoma
Posts: 2,186
Bikes: Hi-Ten bike boomers, a Trek Domane and some projects
Mentioned: 2 Post(s)
Tagged: 0 Thread(s)
Quoted: 884 Post(s)
Liked 2,307 Times
in
1,117 Posts
I have nothing constructive to offer but I love the patina in this photo. Please don't ever try to clean this up.
__________________
"It is the unknown around the corner that turns my wheels." -- Heinz Stücke
"It is the unknown around the corner that turns my wheels." -- Heinz Stücke
Likes For Chuck M:
#7
Full Member
The only thing i see is that the cotters are „reversed“. I don‘t think that‘s a big deal generally and also shouldn‘t cause the feeling you describe. I have this feeling sometimes when i start riding a different bike than the day before. It usually goes away after a few km. So i guess in my case it‘s a perception thing rather then a mechanical problem.
Likes For Kovkov:
#8
Senior Member
Join Date: Jan 2005
Location: Baltimore, MD
Posts: 5,373
Mentioned: 15 Post(s)
Tagged: 0 Thread(s)
Quoted: 2482 Post(s)
Liked 2,954 Times
in
1,678 Posts
See Dave Moulton's page on cotter pin cranks for details on cotter pin maintenance.
Last edited by Trakhak; 09-05-21 at 05:36 AM.
Likes For Trakhak:
Likes For grizzly59:
#11
Senior Member
Join Date: Feb 2012
Location: Rochester, NY
Posts: 18,081
Bikes: Stewart S&S coupled sport tourer, Stewart Sunday light, Stewart Commuting, Stewart Touring, Co Motion Tandem, Stewart 3-Spd, Stewart Track, Fuji Finest, Mongoose Tomac ATB, GT Bravado ATB, JCP Folder, Stewart 650B ATB
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 4204 Post(s)
Liked 3,861 Times
in
2,309 Posts
The pins have an angled contact face. This angle is not a "standard" amount and as it's this face that gets filed as needed to best fit the pin (depth wise) these angles can drift WRT to each other.
I've heard both pin directions as being the "correct one" over the years. These pins reversed from what I do but having inserted pins in both directions many times I find that as long as they are well installed it really won't matter. Andy
I've heard both pin directions as being the "correct one" over the years. These pins reversed from what I do but having inserted pins in both directions many times I find that as long as they are well installed it really won't matter. Andy
__________________
AndrewRStewart
AndrewRStewart
#12
Junior Member
Thread Starter
Join Date: Aug 2014
Posts: 119
Mentioned: 1 Post(s)
Tagged: 0 Thread(s)
Quoted: 63 Post(s)
Liked 28 Times
in
18 Posts
Thanks for all the thoughtful replies! I tried swapping out a different set of pedals from another 3 speed of that era and the wobbly-ness was great improved. Now I'm on the hunt around for another pair of pedals. Thanks!