Go Back  Bike Forums > Bike Forums > Early Brifter Bikes - 7,8, and 9 Speed
Reload this Page >

Is there still hope it it clicks? DA 8 speed brifters revival

Notices
Early Brifter Bikes - 7,8, and 9 Speed Not vintage, not new, but still loved!

Is there still hope it it clicks? DA 8 speed brifters revival

Old 07-21-21, 08:39 AM
  #1  
jonny7
Full Member
Thread Starter
 
Join Date: Oct 2018
Posts: 385

Bikes: 1994 Cadex CFR3, 2006 Scott CR1 SL, Rossin aero, Bertrand GB 2000, Spec Allez Pro

Mentioned: 4 Post(s)
Tagged: 0 Thread(s)
Quoted: 134 Post(s)
Liked 68 Times in 52 Posts
Is there still hope it it clicks? DA 8 speed brifters revival

Hi all, I have a pair of DA brifters which I thought I could revive with the old WD40 / Triflow combo. The right shifter had 1 or 2 clicks in it so I felt like this could just be a matter of dried up grease. After having worked them for quite some time with WD40, I have managed to get the full 7 clicks a few times, but it feels like a lottery. Most of the time I'll just get 1-2 clicks, 3-4 if I'm lucky.

As a more radical solution I tried to to let them soak in Varsol (paint thinner) for a day. The left shifter feels very nice now but the right one is pretty much the same. If I'm very patient and work it a lot, I will end up saving 5-6-7 clicks, but the second after I'll be down to 1-3 clicks.

I was just curious to know it those with more experience in brifter revival would say that the fact that I sometimes get the full range of clicks means the shifter can be saved to a certain extent, and if so, if there is another trick I could try before opening the brifter itself. Or maybe this whole thing is just a lottery in the end and there is really no way to tell? I've spent quite a lot of time on the shifter so far..! Thanks
jonny7 is offline  
Old 07-21-21, 09:21 AM
  #2  
droppedandlost 
small ring
 
droppedandlost's Avatar
 
Join Date: Jul 2012
Location: PNW
Posts: 1,030
Mentioned: 24 Post(s)
Tagged: 0 Thread(s)
Quoted: 437 Post(s)
Liked 925 Times in 370 Posts
Did you receive them this way? It's possible there's a piece of frayed cable in there.
__________________
72 Bob Jackson -- 74 Motobecane Grand Jubile -- 74 Sekine SHS 271 -- 80 Nishiki International
85 Shogun 800 -- 86 Tommasini Super Prestige -- 92 Specialized Rockhopper -- 17 Colnago Arabesque
droppedandlost is offline  
Old 07-21-21, 09:38 AM
  #3  
jonny7
Full Member
Thread Starter
 
Join Date: Oct 2018
Posts: 385

Bikes: 1994 Cadex CFR3, 2006 Scott CR1 SL, Rossin aero, Bertrand GB 2000, Spec Allez Pro

Mentioned: 4 Post(s)
Tagged: 0 Thread(s)
Quoted: 134 Post(s)
Liked 68 Times in 52 Posts
I bought them for cheap thinking I could restore them. So technically not impossible
jonny7 is offline  
Old 07-21-21, 09:44 AM
  #4  
masi61
Senior Member
 
masi61's Avatar
 
Join Date: Oct 2005
Location: SW Ohio
Posts: 3,673

Bikes: Puch Marco Polo, Saint Tropez, Masi Gran Criterium

Mentioned: 25 Post(s)
Tagged: 0 Thread(s)
Quoted: 1158 Post(s)
Liked 439 Times in 312 Posts
Originally Posted by jonny7
I bought them for cheap thinking I could restore them. So technically not impossible
Solvents only get you so far. I haven’t tried it yet but I believe that you can partly disassemble the malfunctioning shifter down to where you can get a better look at the internals. I think I have read that some encrusted grease on the pawls occasionally has to be scraped away. I have a misbehaving front 7800 double STI shifter that is reluctant to downshift and then crunching hard when it finally does release.

Also, I have a lighted magnifier headlamp that I just used to repack my Dura Ace 9000 pedals. Having the magnification can be a bit of a revelation for fussy jobs like this. I kept track of all my loose bearings and adjusted the cones and locknut correctly thanks to the magnification.
masi61 is offline  
Old 07-21-21, 10:22 AM
  #5  
morri869 
Full Member
 
morri869's Avatar
 
Join Date: Oct 2011
Location: Milwaukee, WI
Posts: 403

Bikes: 1984 Lotus Classique, 1996 Cannondale T700

Mentioned: 2 Post(s)
Tagged: 0 Thread(s)
Quoted: 91 Post(s)
Liked 139 Times in 67 Posts
In many cases the shifters have to be taken apart and cleaned manually to restore their complete functionality. If you aren't ready for at least a few hours of painfully precise work it's probably best to just get a functioning pair.
morri869 is offline  
Likes For morri869:
Old 07-21-21, 10:33 AM
  #6  
jonny7
Full Member
Thread Starter
 
Join Date: Oct 2018
Posts: 385

Bikes: 1994 Cadex CFR3, 2006 Scott CR1 SL, Rossin aero, Bertrand GB 2000, Spec Allez Pro

Mentioned: 4 Post(s)
Tagged: 0 Thread(s)
Quoted: 134 Post(s)
Liked 68 Times in 52 Posts
I would loke to use them for a project, but I don't need to use them ASAP. So I might just take them apart then!
jonny7 is offline  
Old 07-21-21, 11:18 AM
  #7  
VtwinVince
Senior Member
 
Join Date: Jul 2018
Posts: 622
Mentioned: 2 Post(s)
Tagged: 0 Thread(s)
Quoted: 164 Post(s)
Likes: 0
Liked 244 Times in 142 Posts
Sounds like a complete disassemble is in order here. I did this with a set of first-gen Shimano 600 units which were completely frozen. Disassembled, cleaned, regreased and then put back together with a tool which I had to manufacture, so not easy, but they work beautifully now.
VtwinVince is offline  
Likes For VtwinVince:
Old 07-21-21, 05:11 PM
  #8  
dddd
Ride, Wrench, Swap, Race
 
dddd's Avatar
 
Join Date: Jan 2010
Location: Northern California
Posts: 9,171

Bikes: Cheltenham-Pedersen racer, Boulder F/S Paris-Roubaix, Varsity racer, '52 Christophe, '62 Continental, '92 Merckx, '75 Limongi, '76 Presto, '72 Gitane SC, '71 Schwinn SS, etc.

Mentioned: 132 Post(s)
Tagged: 0 Thread(s)
Quoted: 1554 Post(s)
Liked 1,274 Times in 846 Posts
Are you getting missed shifts with the cable installed (with tension), or just by operating the shifter by itself?

It may work fine with the cable tension applied.

You didn't mention which direction of shifts are intermittent, pulling cable or releasing cable(?).
dddd is offline  
Likes For dddd:
Old 07-21-21, 08:43 PM
  #9  
jonny7
Full Member
Thread Starter
 
Join Date: Oct 2018
Posts: 385

Bikes: 1994 Cadex CFR3, 2006 Scott CR1 SL, Rossin aero, Bertrand GB 2000, Spec Allez Pro

Mentioned: 4 Post(s)
Tagged: 0 Thread(s)
Quoted: 134 Post(s)
Liked 68 Times in 52 Posts
Originally Posted by dddd
Are you getting missed shifts with the cable installed (with tension), or just by operating the shifter by itself?

It may work fine with the cable tension applied.

You didn't mention which direction of shifts are intermittent, pulling cable or releasing cable(?).
Good points! I have not tried it with cable tension, as I thought it wouldn't work since the shifting is veeeeeery inconsistant. If I work the small lever with resolution, I know I'll end up getting 1-2 extra clicks, but the gain is momentary. The second after the clicks are gone. This answers your second question: it's the small lever that seems to be malfunctioning. Whenever I get it to work, I know that I'll be able to pull the cable one click up.
jonny7 is offline  
Old 07-21-21, 09:13 PM
  #10  
Jimbo1983
Junior Member
 
Join Date: Mar 2011
Location: New Zealand
Posts: 186
Mentioned: 1 Post(s)
Tagged: 0 Thread(s)
Quoted: 54 Post(s)
Liked 48 Times in 31 Posts
Definitely try with cable tension. I've had good success with all types of those old 8 speed levers by fitting a cable or even just a short length of old cable with the ferrule still attached.
Jimbo1983 is offline  
Old 07-22-21, 12:59 AM
  #11  
Fivethumbs
Full Member
 
Join Date: Apr 2007
Posts: 253
Mentioned: 2 Post(s)
Tagged: 0 Thread(s)
Quoted: 34 Post(s)
Likes: 0
Liked 22 Times in 12 Posts
I rebuilt some Shimano 8 speed STI shifters. There is a special nut that needs to be removed with a special tool. I made the tool myself out of a socket and dremel tool. I took photos with my phone every step of the way because there are so many little parts that are in a very particular order. It was a pain and if not for the photos I would not have been able to put them back together. When I got them apart, the problem was old grease that had taken on the consistency of old peanut butter so that nothing could move. I realized then that I did not need to take them completely apart and only needed to take them apart to a certain point and then soak the parts in solvent.
Fivethumbs is offline  
Old 07-22-21, 07:18 PM
  #12  
Homebrew01
Super Moderator
 
Homebrew01's Avatar
 
Join Date: Jul 2004
Location: Ffld Cnty Connecticut
Posts: 21,845

Bikes: Old Steelies I made, Old Cannondales

Mentioned: 12 Post(s)
Tagged: 0 Thread(s)
Quoted: 1173 Post(s)
Liked 924 Times in 610 Posts
Moved from C & V.
__________________
Bikes: Old steel race bikes, old Cannondale race bikes, less old Cannondale race bike, crappy old mtn bike.

FYI: https://www.bikeforums.net/forum-sugg...ad-please.html
Homebrew01 is offline  
Old 01-08-22, 10:04 AM
  #13  
wrk101
Thrifty Bill
 
wrk101's Avatar
 
Join Date: Jan 2008
Location: Mountains of Western NC
Posts: 23,572

Bikes: 86 Katakura Silk, 87 Prologue X2, 88 Cimarron LE, 1975 Sekai 4000 Professional, 73 Paramount, plus more

Mentioned: 96 Post(s)
Tagged: 0 Thread(s)
Quoted: 1236 Post(s)
Liked 958 Times in 625 Posts
If the hoods and other cosmetics are good, either rebuild yourself, or pay someone to rebuilt. There are a couple of people on ebay selling rebuild services at a reasonable price. Myself, I keep the 56400 and 7400 brifters for this purpose. The beauty of the 8 speed stuff is that it is rebuildable.

IMHO, the solvent flush is a joke, waste of time, and is temporary at best.

Last edited by wrk101; 01-10-22 at 09:50 PM.
wrk101 is offline  
Likes For wrk101:
Old 01-09-22, 06:49 PM
  #14  
jonny7
Full Member
Thread Starter
 
Join Date: Oct 2018
Posts: 385

Bikes: 1994 Cadex CFR3, 2006 Scott CR1 SL, Rossin aero, Bertrand GB 2000, Spec Allez Pro

Mentioned: 4 Post(s)
Tagged: 0 Thread(s)
Quoted: 134 Post(s)
Liked 68 Times in 52 Posts
Originally Posted by wrk101
Myself, I keep the 56400 and 7400 brifters for this purpose. The beauty of the 8 speed stuff is that it is rebuildable.
.
Do you follow any guide/video when it comes to deassembly/reassembly?
jonny7 is offline  
Old 01-10-22, 09:51 PM
  #15  
wrk101
Thrifty Bill
 
wrk101's Avatar
 
Join Date: Jan 2008
Location: Mountains of Western NC
Posts: 23,572

Bikes: 86 Katakura Silk, 87 Prologue X2, 88 Cimarron LE, 1975 Sekai 4000 Professional, 73 Paramount, plus more

Mentioned: 96 Post(s)
Tagged: 0 Thread(s)
Quoted: 1236 Post(s)
Liked 958 Times in 625 Posts
I just have them rebuilt by others. I put my time into other repairs.
wrk101 is offline  

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


Thread Tools
Search this Thread

Contact Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service -

Copyright © 2024 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.