Go Back  Bike Forums > Bike Forums > Classic & Vintage
Reload this Page >

Lightest steel that accepts wider tires?

Notices
Classic & Vintage This forum is to discuss the many aspects of classic and vintage bicycles, including musclebikes, lightweights, middleweights, hi-wheelers, bone-shakers, safety bikes and much more.

Lightest steel that accepts wider tires?

Old 07-31-21, 07:19 AM
  #1  
RH Clark
Senior Member
Thread Starter
 
Join Date: Jun 2019
Posts: 902
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 522 Post(s)
Liked 449 Times in 246 Posts
Lightest steel that accepts wider tires?

I have acquired a love for steel bikes. I mostly ride a Surly LHT, Trek 400, Lemond in 853 and a Miyata 610. I would love to own a light weight steel bike that would accept at least 32mm tires. Unfortunately my budget won't allow for a new purchase. Were there any older high end frames of light steel that accepted wider tires? I have been able to locate a few local bikes in 853 but nothing so far that accepts anything wider than 25mm or possibly 28mm tires. Any model names you guys could give me to be on the look out for would be greatly appreciated. It doesn't have to be an 853 steel bike but I would love to be right in the 20 lb range for a complete 58cm-60cm bike. Possibly a pipe dream but I thought I would ask.

Last edited by RH Clark; 07-31-21 at 07:45 AM.
RH Clark is offline  
Old 07-31-21, 07:43 AM
  #2  
steelbikeguy
Senior Member
 
steelbikeguy's Avatar
 
Join Date: Feb 2008
Location: Peoria, IL
Posts: 4,449
Mentioned: 86 Post(s)
Tagged: 0 Thread(s)
Quoted: 1820 Post(s)
Liked 3,326 Times in 1,563 Posts
that's an interesting question!
I've got a 1987 Hetchins made with 531C that I recently put some 25mm Continental Grand Prix Classic tires on, and they barely fit. Maybe a mm or two between the tire and brakes?

That prompted me to look at my 753 Raleigh Team, circa 1982, and it is the same situation. Both bikes use Campy short reach brakes and the brake pads are at the top of the slots.
Of course, this was the era when fast bikes had the tightest clearances possible. I'm not sure when that went out of style... possibly after carbon bikes became relatively common?

One of the few options I can think of would be to look for a bike that isn't intended to be a criterium racer, such as a cyclo-cross bike. Of course, that means you end up with cantilever brakes and weird cable routing.
The other option would be to find a bike that pre-dated tight clearances. The only one that comes to mind is the Sekai 5000 frameset. This was built with some very thin gauge tubing. To my knowledge, these weren't widely available, so finding one could be a challenge.
edit: I see that the article mentions tight clearances, so getting even a 25mm tire installed might be a challenge.
Attached is a magazine review of the frame....







Steve in Peoria
steelbikeguy is offline  
Old 07-31-21, 08:02 AM
  #3  
Mr. 66
Senior Member
 
Mr. 66's Avatar
 
Join Date: Aug 2015
Posts: 3,440
Mentioned: 39 Post(s)
Tagged: 0 Thread(s)
Quoted: 1124 Post(s)
Liked 1,704 Times in 941 Posts
I've been working on my Rocky Mountain Sherpa 30 made of 853, this will handle Big Apple or Fat Franks.
Mr. 66 is offline  
Old 07-31-21, 08:37 AM
  #4  
fishboat
Senior Member
 
Join Date: Feb 2016
Location: SE Wisconsin
Posts: 1,888

Bikes: Lemond '01 Maillot Jaune, Lemond '02 Victoire, Lemond '03 Poprad, Lemond '03 Wayzata DB conv(Poprad), '79 AcerMex Windsor Carrera Professional(pur new), '88 GT Tequesta(pur new), '01 Bianchi Grizzly, 1993 Trek 970 DB conv, Trek 8900 DB conv

Mentioned: 12 Post(s)
Tagged: 0 Thread(s)
Quoted: 750 Post(s)
Likes: 0
Liked 799 Times in 467 Posts
Perhaps a 650B conversion may give you the widest options for bike selection in combo with wider tires. Some bikes are better candidates than others. I remember seeing a Lemond Buenos Aires(max tire, stock bike would be a 28mm I think) somewhere that had a 650b conversion done..it was running 38-40mm tires I think..been a while. Looked good, as I remember.

Do a search here on BF for "650b conversion" in thread titles..you'll get lots of hits.
fishboat is offline  
Likes For fishboat:
Old 07-31-21, 08:58 AM
  #5  
th0m
Senior Member
 
Join Date: Sep 2020
Location: Sweden
Posts: 60
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 23 Post(s)
Liked 46 Times in 17 Posts
My mid 90's Colnago Master Olympic takes 28 mm tyres easily. Never tried anything bigger, but quite sure you could fit 30 or possibly even 32 mm tyres without issue.
th0m is offline  
Old 07-31-21, 09:00 AM
  #6  
gugie 
Bike Butcher of Portland
 
gugie's Avatar
 
Join Date: Jul 2014
Location: Portland, OR
Posts: 11,639

Bikes: It's complicated.

Mentioned: 1299 Post(s)
Tagged: 0 Thread(s)
Quoted: 4668 Post(s)
Liked 5,766 Times in 2,271 Posts
What's "wide" to you? Some think 28mm wide tires are wide, others want to go >2 inches.

Overlooked (because they're harder to find) are older, low volume English framebuiders, such as Gillott and Ephgrave. I pick these two as I've done 650b conversions with them, 42mm wide tires as the goal (met). On both of these frames I have no idea what frame tubing was used, but clearly they picked some of the lightest tubing available at the time. 650b conversions are a great way to fit wider tires into vintage frames.

Note that a frame that weights a half pound lighter won't make much difference at all from a heavier one just on weight itself - drink a third of a full water bottlee and you've lost half a pound. The frame, however, will be much more lively and compliant due to thinner wall tubing.
__________________
If someone tells you that you have enough bicycles and you don't need any more, stop talking to them. You don't need that kind of negativity in your life.
gugie is online now  
Old 07-31-21, 09:02 AM
  #7  
The Golden Boy 
Extraordinary Magnitude
 
The Golden Boy's Avatar
 
Join Date: Aug 2009
Location: Waukesha WI
Posts: 13,640

Bikes: 1978 Trek TX700; 1978/79 Trek 736; 1984 Specialized Stumpjumper Sport; 1984 Schwinn Voyageur SP; 1985 Trek 620; 1985 Trek 720; 1986 Trek 400 Elance; 1987 Schwinn High Sierra; 1990 Miyata 1000LT

Mentioned: 84 Post(s)
Tagged: 0 Thread(s)
Quoted: 2597 Post(s)
Liked 1,678 Times in 926 Posts
Originally Posted by RH Clark
Were there any older high end frames of light steel that accepted wider tires?
Check out this: https://www.bikeforums.net/classic-v...hall-fame.html

Old bikes generally don't have room for tires wider than 35- but 32 is usually doable. Tourers are generally going to be heavier- as they're meant to carry loads. Sport tourers generally are heavier because they're generally meantto be "less expensive" bikes. HOWEVER... there were sport tourers that had premium tube sets, as well as room for 32s- and sometimes premium components. The ones that kind of jump out are the 83-ish Trek 700 and Specialized Sequoia. In addtion- they're generally good candidates for conversion to 650B wheels.
__________________
*Recipient of the 2006 Time Magazine "Person Of The Year" Award*

Commence to jigglin’ huh?!?!

"But hey, always love to hear from opinionated amateurs." -says some guy to Mr. Marshall.
The Golden Boy is offline  
Likes For The Golden Boy:
Old 07-31-21, 09:11 AM
  #8  
Fahrenheit531 
52psi
 
Fahrenheit531's Avatar
 
Join Date: Aug 2013
Location: Tucson, AZ
Posts: 4,134

Bikes: Schwinn Volare ('78); Raleigh Competition GS ('79)

Mentioned: 29 Post(s)
Tagged: 0 Thread(s)
Quoted: 790 Post(s)
Liked 800 Times in 390 Posts
Originally Posted by The Golden Boy
Old bikes generally don't have room for tires wider than 35- but 32 is usually doable.
This. I have been able to comfortably run 700c x 32 on my 1978 Schwinn Volare, '79 Raleigh Comp GS, and '71 Schwinn Paramount. Small sample size, but 100% success rate, so if that's what you're aiming for you may find it less troublesome than you expect.
__________________
A race bike in any era is a highly personal choice that at its "best" balances the requirements of fit, weight, handling, durability and cost tempered by the willingness to toss it and oneself down the pavement at considerable speed. ~Bandera
Fahrenheit531 is offline  
Old 07-31-21, 09:16 AM
  #9  
seypat
Senior Member
 
Join Date: Oct 2010
Posts: 8,755
Mentioned: 69 Post(s)
Tagged: 0 Thread(s)
Quoted: 3190 Post(s)
Liked 2,460 Times in 1,489 Posts
Get a frame originally made for 27" wheels and convert to 650. You should be able to put some big uns on there then. Really, though you're only gonna get so much weight savings on the frame. Putting some big a$$ tires on will negate the savings some. You'll need to weight weenie your components. Also, I believe the frame companies start beefing up the frames in the 58-60 range.

Last edited by seypat; 07-31-21 at 09:20 AM.
seypat is offline  
Old 07-31-21, 09:28 AM
  #10  
seypat
Senior Member
 
Join Date: Oct 2010
Posts: 8,755
Mentioned: 69 Post(s)
Tagged: 0 Thread(s)
Quoted: 3190 Post(s)
Liked 2,460 Times in 1,489 Posts
I think Vitus made some light frames. I think they also had a reputation for being noodly. Someone with more knowledge can elaborate.
seypat is offline  
Old 07-31-21, 09:37 AM
  #11  
Darth Lefty 
Disco Infiltrator
 
Darth Lefty's Avatar
 
Join Date: May 2013
Location: Folsom CA
Posts: 13,775

Bikes: Stormchaser, Paramount, Tilt, Samba tandem

Mentioned: 72 Post(s)
Tagged: 0 Thread(s)
Quoted: 3126 Post(s)
Liked 2,102 Times in 1,366 Posts
My 1970's Paramount P10-9 barely fits 32-630 Paselas. But tubulars were a factory option so the brakes are set right between 630 and 622. Therefore it would have no trouble with 32-622, 35-622 might be pushing it at the chain stays. Full 531 and it rides sublime.

(But it does not have bottle bosses, chain hanger, pump peg that you get on an 80's bike. And the brakes and shifting are poor.)

To get that sublime ride you need at least a chromoly and preferably a branded-tubing fork, and it needs to be roadie-spec. It needs to flex. If you went to a drop bar MTB, you need the big tires... a MTB fork is stiff as hell
__________________
Genesis 49:16-17
Darth Lefty is offline  
Old 07-31-21, 09:38 AM
  #12  
bikemig 
Senior Member
 
bikemig's Avatar
 
Join Date: Apr 2012
Location: Middle Earth (aka IA)
Posts: 20,505

Bikes: A bunch of old bikes and a few new ones

Mentioned: 178 Post(s)
Tagged: 0 Thread(s)
Quoted: 5877 Post(s)
Liked 3,445 Times in 2,066 Posts
finding older bikes that take 32c is easy. In fact here is a long thread on that

https://www.bikeforums.net/classic-v...g-bicycle.html

But by and large most vintage bikes will be north of 20 lbs once you build it up. That's an aggressive weight for an older bike that you are not likely to hit if the bike is made of Reynolds 531, columbus SL/SP, or any of the good Japanese chrome moly tubing sets (Ishiwata, Tange).

Super vitus 980 built up a nice light bike and you could try your hand at a 650b conversion but finding an appropriate frame for a 650b conversion is another story.
bikemig is offline  
Old 07-31-21, 09:40 AM
  #13  
nlerner
Senior Member
 
Join Date: Dec 2005
Posts: 17,127
Mentioned: 480 Post(s)
Tagged: 0 Thread(s)
Quoted: 3788 Post(s)
Liked 6,573 Times in 2,580 Posts
Originally Posted by fishboat
Perhaps a 650B conversion may give you the widest options for bike selection in combo with wider tires. Some bikes are better candidates than others. I remember seeing a Lemond Buenos Aires(max tire, stock bike would be a 28mm I think) somewhere that had a 650b conversion done..it was running 38-40mm tires I think..been a while. Looked good, as I remember.

Do a search here on BF for "650b conversion" in thread titles..you'll get lots of hits.
This ^, particularly since you already have the bike in hand. Here's mine and my buddy's Lemond Buenos Aires 650B x 38mm builds. We both had to dimple the chainstays a bit, but was able to do that with my bench vise.

nlerner is offline  
Likes For nlerner:
Old 07-31-21, 10:16 AM
  #14  
Darth Lefty 
Disco Infiltrator
 
Darth Lefty's Avatar
 
Join Date: May 2013
Location: Folsom CA
Posts: 13,775

Bikes: Stormchaser, Paramount, Tilt, Samba tandem

Mentioned: 72 Post(s)
Tagged: 0 Thread(s)
Quoted: 3126 Post(s)
Liked 2,102 Times in 1,366 Posts
I'll also point out, since this is C&V, that a lot of adds-lightness tricks are not C&V, but can go on a C&V frame if you want. And/or can also make for a better experience and keep you from shopping in other peoples' parts bins. A 105 R7000 crankset & bb saves >100 grams over Nuovo Record, and it's hardly the lightest thing you can find. It also gives you shift ramps and pins and a lower front gear, and you can buy a matching power meter. Spreading the rear for a 130mm freehub might not do anything for the weight but lets you have any of today's cassettes... which shift better even on friction. While you are at it 622 (700c) rims and tires are an easy win, most of the time. Velocity will sell you some nice ones, and they can be tubeless if you want. I haven't undertaken this project on my Paramount because, hey, it's a Paramount. But if I had something more mass-manufactured like many many 1980's Taiwanese bikes, I wouldn't hesitate so much. I did a Shimergo conversion on my Expert TG and it's been pretty great.
__________________
Genesis 49:16-17
Darth Lefty is offline  
Likes For Darth Lefty:
Old 07-31-21, 10:19 AM
  #15  
RH Clark
Senior Member
Thread Starter
 
Join Date: Jun 2019
Posts: 902
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 522 Post(s)
Liked 449 Times in 246 Posts
Thanks' guys. I should have specified on tire size closer before. I have a Marlin 5 for my wider tire needs. My Trek 400 currently has 32's on it and I like it a lot. I wish it was 5 lbs lighter .I have my Miyata set up with the original 27x1-1/4 as well as a 700c set with 38's. Anyway,I really like the 38's on my Miyata which got me thinking how great it would be to have a bike as light as my Lemond, currently 18lbs, but still be able to take up to a 32 and optimistically, maybe a 35mm.

Honestly, I feel pretty blessed to have some really nice bikes that I bought real cheap but I can't help thinking about the next one.
RH Clark is offline  
Old 07-31-21, 11:17 AM
  #16  
The Golden Boy 
Extraordinary Magnitude
 
The Golden Boy's Avatar
 
Join Date: Aug 2009
Location: Waukesha WI
Posts: 13,640

Bikes: 1978 Trek TX700; 1978/79 Trek 736; 1984 Specialized Stumpjumper Sport; 1984 Schwinn Voyageur SP; 1985 Trek 620; 1985 Trek 720; 1986 Trek 400 Elance; 1987 Schwinn High Sierra; 1990 Miyata 1000LT

Mentioned: 84 Post(s)
Tagged: 0 Thread(s)
Quoted: 2597 Post(s)
Liked 1,678 Times in 926 Posts
Originally Posted by RH Clark
My Trek 400 currently has 32's on it and I like it a lot. I wish it was 5 lbs lighter .
You're not saving 5 pounds on a steel frame. A decent steel frame is around 6 pounds. If you've got a stock build on that Trek 400, you can save a lot on your build.
__________________
*Recipient of the 2006 Time Magazine "Person Of The Year" Award*

Commence to jigglin’ huh?!?!

"But hey, always love to hear from opinionated amateurs." -says some guy to Mr. Marshall.
The Golden Boy is offline  
Old 07-31-21, 11:26 AM
  #17  
squirtdad
Senior Member
 
squirtdad's Avatar
 
Join Date: Jul 2006
Location: San Jose (Willow Glen) Ca
Posts: 9,848

Bikes: Kirk Custom JK Special, '84 Team Miyata,(dura ace old school) 80?? SR Semi-Pro 600 Arabesque

Mentioned: 104 Post(s)
Tagged: 0 Thread(s)
Quoted: 2302 Post(s)
Liked 2,737 Times in 1,497 Posts
total bike weight bike weight is overrated so a large degree. sure difference between 30 and 20 is noticable but 22 and 20??

any way I can fit a 30mm corsa control tubular in my 85 team miyata, run 28 easily with both it and my 84 team miyata.

another thing to look at is wheelset.... a lighter wheelset can make an amazing difference. I see this with the difference between a mavic gel 330 tubular set and a mavic ma40 clincher on the 84 miyata. so consider going tubular

good luck
__________________
Life is too short not to ride the best bike you have, as much as you can
(looking for Torpado Super light frame/fork or for Raleigh International frame fork 58cm)



squirtdad is offline  
Old 07-31-21, 11:42 AM
  #18  
alcjphil
Senior Member
 
alcjphil's Avatar
 
Join Date: Jun 2002
Location: Montreal, Quebec
Posts: 5,869
Mentioned: 16 Post(s)
Tagged: 0 Thread(s)
Quoted: 1792 Post(s)
Liked 1,671 Times in 955 Posts
Originally Posted by The Golden Boy
You're not saving 5 pounds on a steel frame. A decent steel frame is around 6 pounds. If you've got a stock build on that Trek 400, you can save a lot on your build.
This: It is impossible to save 5 pounds on a steel bike by changing to a lighter frame. Don't forget as well that the wider the tire the more it weighs unless you can find very lightweight wide tires. Steel bikes that weigh under 20 pounds have to use the lightest weight components possible
alcjphil is offline  
Old 07-31-21, 12:11 PM
  #19  
ThermionicScott 
working on my sandal tan
 
ThermionicScott's Avatar
 
Join Date: Aug 2011
Location: CID
Posts: 22,625

Bikes: 1991 Bianchi Eros, 1964 Armstrong, 1988 Diamondback Ascent, 1988 Bianchi Premio, 1987 Bianchi Sport SX, 1980s Raleigh mixte (hers), All-City Space Horse (hers)

Mentioned: 98 Post(s)
Tagged: 0 Thread(s)
Quoted: 3868 Post(s)
Liked 2,560 Times in 1,574 Posts
+1 on considering a 650B conversion. Pretty straightforward way to get ~38mm tires into just about any C&V frame.

18 lbs is optimistic, but low 20s is fairly easy to accomplish without resorting to anything expensive and/or stupid.

Last edited by ThermionicScott; 08-01-21 at 04:32 PM.
ThermionicScott is offline  
Old 07-31-21, 12:28 PM
  #20  
SurferRosa
señor miembro
 
SurferRosa's Avatar
 
Join Date: Dec 2018
Location: Pac NW
Posts: 8,464

Bikes: '70s - '80s Campagnolo

Mentioned: 92 Post(s)
Tagged: 0 Thread(s)
Quoted: 3846 Post(s)
Liked 6,437 Times in 3,183 Posts
Originally Posted by seypat
Get a frame originally made for 27" wheels and convert to 650...
Or even 700c, if 32mm is sufficient.
SurferRosa is offline  
Likes For SurferRosa:
Old 07-31-21, 03:35 PM
  #21  
John E
feros ferio
 
John E's Avatar
 
Join Date: Jul 2000
Location: www.ci.encinitas.ca.us
Posts: 21,765

Bikes: 1959 Capo Modell Campagnolo; 1960 Capo Sieger (2); 1962 Carlton Franco Suisse; 1970 Peugeot UO-8; 1982 Bianchi Campione d'Italia; 1988 Schwinn Project KOM-10;

Mentioned: 44 Post(s)
Tagged: 0 Thread(s)
Quoted: 1384 Post(s)
Liked 1,294 Times in 819 Posts
My 1980 Peugeot PKN-10, now my son's kiddie puller, takes up to 700Cx35 tires. This was one of its more endearing features, and I would have kept it if it had been one size smaller.

My old PKN-10, now my son's kiddie-puller, although the boys are getting big for the trailer now.
__________________
"Far and away the best prize that life offers is the chance to work hard at work worth doing." --Theodore Roosevelt
Capo: 1959 Modell Campagnolo, S/N 40324; 1960 Sieger (2), S/N 42624, 42597
Carlton: 1962 Franco Suisse, S/N K7911
Peugeot: 1970 UO-8, S/N 0010468
Bianchi: 1982 Campione d'Italia, S/N 1.M9914
Schwinn: 1988 Project KOM-10, S/N F804069
John E is offline  
Old 07-31-21, 05:01 PM
  #22  
non-fixie 
Shifting is fun!
 
non-fixie's Avatar
 
Join Date: Aug 2009
Location: South Holland, NL
Posts: 11,001

Bikes: Yes, please.

Mentioned: 277 Post(s)
Tagged: 0 Thread(s)
Quoted: 2182 Post(s)
Liked 4,525 Times in 1,743 Posts
Find a racing frame from before 1980 built with Reynolds 531 or equivalent. It will most probably take 700x32C. Build it with lightweight parts and decent tires and you'll have a wonderful bike, weighing 22-24 lbs. Maybe a bit less if you choose tubulars.

I once managed to get a fendered 25" bike with clinchers down to 10 kgs (~22 lbs) without breaking the bank, but that was pushing it:

__________________
Are we having fun, or what ...



non-fixie is online now  
Old 07-31-21, 05:55 PM
  #23  
Doug Fattic 
framebuilder
 
Join Date: Dec 2009
Location: Niles, Michigan
Posts: 1,459
Mentioned: 50 Post(s)
Tagged: 0 Thread(s)
Quoted: 610 Post(s)
Liked 1,905 Times in 647 Posts
Originally Posted by gugie
What's "wide" to you? Some think 28mm wide tires are wide, others want to go >2 inches.

Overlooked (because they're harder to find) are older, low volume English framebuiders, such as Gillott and Ephgrave. I pick these two as I've done 650b conversions with them, 42mm wide tires as the goal (met). On both of these frames I have no idea what frame tubing was used, but clearly they picked some of the lightest tubing available at the time. 650b conversions are a great way to fit wider tires into vintage frames.

Note that a frame that weights a half pound lighter won't make much difference at all from a heavier one just on weight itself - drink a third of a full water bottlee and you've lost half a pound. The frame, however, will be much more lively and compliant due to thinner wall tubing.
There are some nice older British bikes that might work for you. The Gillot and Ephgrave Mark mentioned are top quality and would command a premium price. However there were many builders in the UK during the classic period (when I was traveling around England in the early 70's looking for someone to teach me, my address book contained well over 100). Many of them are not well known and as a result have a lower value today even though some are high quality. I learned at Ellis Briggs in Shipley West Yorkshire (part of the Bradford/Leeds metropolitan area). That area just wasn't a tourist place so builders in that vicinity don't get as much love as they deserve.

British Bicycles made in the classic era had to be all around useful. They were primary individual transportation and had to have clearance for mudguards. Longer chain stays and center pull brake clearance provides a lot more room for fatter tires. Italian bikes were and are full on road racing machines so there isn't much point in considering those. Somewhere in the late 70's Campy went from making 47/57 mm brakes to 40/50 (or 39/49 if they are made in Japan). That kind of brake clearance is not helpful for fatter tires. And to make things worse brake clearance distance usually put the brake blocks at the top of the slot. Americans wanted go fast bikes so most of them are out of consideration. However Trek did make some steel sport touring frames that can easily handle 32s.

One option for those not on a tight budget and want light steel combined with fatter tire clearance is to make the frame yourself. For most people that would require taking a frame building class. I've had lots of students that have made a frame with that combination. How much I need to help them depends on their natural skill and their future plans. Rene Herse sells light tubing and frame materials just for that purpose. I'm going to emphasize what gugie wrote that a light tubed frame has a lively feel that standard double butted tubing does not.

I just made a bicycle for my wife out of the Kaisai light tubing with angled chain stays that work well for 650B X 42 tires. This one is for MUT riding. She has other bikes for other purposes. It rides like a dream. I'll attach a picture.
Doug Fattic is offline  
Likes For Doug Fattic:
Old 07-31-21, 06:17 PM
  #24  
Classtime 
Senior Member
 
Classtime's Avatar
 
Join Date: Jan 2015
Location: Los Angeles
Posts: 4,672

Bikes: 82 Medici, 2011 Richard Sachs, 2011 Milwaukee Road

Mentioned: 54 Post(s)
Tagged: 0 Thread(s)
Quoted: 1924 Post(s)
Liked 1,954 Times in 1,086 Posts
My '69 PX-10 had 32mm Tufo cyclocross knobbies on it for a while with plenty of clearance. Surprisingly light but never weighed it.
__________________
I don't do: disks, tubeless, e-shifting, or bead head nymphs.
Classtime is offline  
Old 07-31-21, 06:29 PM
  #25  
randyjawa 
Senior Member
 
randyjawa's Avatar
 
Join Date: Apr 2007
Location: Thunder Bay, Ontario, Canada - burrrrr!
Posts: 11,672

Bikes: 1958 Rabeneick 120D, 1968 Legnano Gran Premio, 196? Torpado Professional, 2000 Marinoni Piuma

Mentioned: 210 Post(s)
Tagged: 0 Thread(s)
Quoted: 1370 Post(s)
Likes: 0
Liked 1,743 Times in 934 Posts
I am not sure if my 1982 Bianchi would qualify as light but I do know for sure that 32s will fit just barely.

I keep the Bianchi in Jamaica and when my original tires failed, The bike shop in Black River had a set of 23s but, try as I could, I could not get them to fit on the rims. The front one was a struggle to mount and, finally, I gave up on trying to do the rear.

I ordered a set of 28s (what I already had on the bike), however; a set of 32s arrived. I told the bike shop guy, a friend, that I would see if they fit. The set set me back $26.00 US. Well, they did fit (just barely clearing the chain stays) and I love them. In fact, these days I always opt for bigger tires thanks to what I learned from this experience...

Getting that 23 mounted was really really hard to do...


So, I went with the 32s and wow - bigger is better..!
__________________
"98% of the bikes I buy are projects".
randyjawa is online now  
Likes For randyjawa:

Thread Tools
Search this Thread

Contact Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service -

Copyright © 2024 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.