Lightweight, strong trailer floor?
#1
Junior Member
Thread Starter
Lightweight, strong trailer floor?
I have taken this kid's trailer (Chariot model no longer in production) apart to turn it into a cargo trailer, and possibly a micro camper too.
I sometimes haul heavy stuff (e.g. compost, small furniture) so the floor needs to be sturdy enough to withstand 50-60 kg of weight.
I am getting stuck at floor options: Marine plywood, aluminium, PEHD, Coroplast, foam tiles, linoleum?
What did you use? Or what do you recommend?
Chariot Corsaire
I sometimes haul heavy stuff (e.g. compost, small furniture) so the floor needs to be sturdy enough to withstand 50-60 kg of weight.
I am getting stuck at floor options: Marine plywood, aluminium, PEHD, Coroplast, foam tiles, linoleum?
What did you use? Or what do you recommend?
Chariot Corsaire
Last edited by SagaInColours; 05-31-22 at 12:08 PM.
Likes For SagaInColours:
#2
Senior Member
Join Date: Dec 2006
Location: Houston, TX
Posts: 895
Bikes: 2017 Co-op ADV 1.1; ~1991 Novara Arriba; 1990 Fuji Palisade; mid-90's Moots Tandem; 1985 Performance Superbe
Mentioned: 1 Post(s)
Tagged: 0 Thread(s)
Quoted: 390 Post(s)
Liked 572 Times
in
332 Posts
I’ve had good luck with shelving:
https://www.bikeforums.net/21220581-post693.html
For high point loads, I have a sheet of 1/4” plywood that I use to distribute the weight.
https://www.bikeforums.net/21220581-post693.html
For high point loads, I have a sheet of 1/4” plywood that I use to distribute the weight.
Likes For flangehead:
#3
Galveston County Texas
Join Date: Nov 2007
Location: In The Wind
Posts: 33,221
Bikes: 02 GTO, 2011 Magnum
Mentioned: 19 Post(s)
Tagged: 0 Thread(s)
Quoted: 1350 Post(s)
Liked 1,243 Times
in
621 Posts
3/8 plywood on top of the frame
__________________
Fred "The Real Fred"
Fred "The Real Fred"
Last edited by 10 Wheels; 05-31-22 at 12:48 PM. Reason: Add pic
Likes For 10 Wheels:
#4
Full Member
Join Date: Mar 2022
Location: SW WI
Posts: 218
Bikes: Cannondale Topstone, Trek Dual Sport, State Bicycle Klunker
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 87 Post(s)
Liked 132 Times
in
69 Posts
I’d look for 1/4 HDPE it’s light strong and of course waterproof and extremely easy to work with. drill a hole and zip tie it to the frame. The other option may be aluminum which you could still cut with a circular saw but would have to do more grinding on the edges for it to be less abrasive to the zip ties. Screws will only as weight and the vibrations may work them out of the frame.
I’m thinking the plywood may hold moisture and add weight.
I’m thinking the plywood may hold moisture and add weight.
Likes For Bogey Speedwell:
#5
Junior Member
Thread Starter
I’ve had good luck with shelving:
https://www.bikeforums.net/21220581-post693.html
For high point loads, I have a sheet of 1/4” plywood that I use to distribute the weight.
https://www.bikeforums.net/21220581-post693.html
For high point loads, I have a sheet of 1/4” plywood that I use to distribute the weight.
#6
Junior Member
Thread Starter
#8
Full Member
Join Date: Mar 2022
Location: SW WI
Posts: 218
Bikes: Cannondale Topstone, Trek Dual Sport, State Bicycle Klunker
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 87 Post(s)
Liked 132 Times
in
69 Posts
should handle anything you want to pull. Use the frame as support, so the platform is on top of the frame. Pretty confident you won’t be able to break it unless you are using it at sub zero temps. I occasionally work with it and it is stronger than 3/8 plywood and think it would be more durable than 1/2” plywood. I’ve tried to bend it with a heat gun to bend pieces to make diy cargo cages and I gave up, was able to bend it but not very well and none broke under my manipulation.