Re-spoking questions
#1
Junior Member
Thread Starter
Re-spoking questions
I'm about to upgrade to a generator lighting system which will obviously necessitate wheelbuilding. This isn't my first set of wheels, so that's not my question. Roger Musson's book got me through the last set of wheels with flying colors, and I'm confident it won't let me down this time as well. However, I'd like to go ahead and order spokes ahead of time to minimize the time my bike is out of commission.
I'm planning on using my existing rims (Alex MD-21), and while I'm rebuilding my front wheel, I figure I'll go ahead and re-spoke the rear wheel, both to replace the straight-gauge spokes with butted ones and to match the front. I know from my last pair (that I used Alex Adventurer 2 rims on) that the manufacturer's published ERD was 4mm less than what I measured, so I don't want to rely on the published ERD for these rims. I also don't want to disassemble my wheels to measure spokes and ERD and then wait a week or more for new spokes and nipples to arrive while my bike sits forlorn and unshod. So that leads to 2 questions:
I'm planning on using my existing rims (Alex MD-21), and while I'm rebuilding my front wheel, I figure I'll go ahead and re-spoke the rear wheel, both to replace the straight-gauge spokes with butted ones and to match the front. I know from my last pair (that I used Alex Adventurer 2 rims on) that the manufacturer's published ERD was 4mm less than what I measured, so I don't want to rely on the published ERD for these rims. I also don't want to disassemble my wheels to measure spokes and ERD and then wait a week or more for new spokes and nipples to arrive while my bike sits forlorn and unshod. So that leads to 2 questions:
- Is there a reliable (and not too difficult) method to measure ERD on a built-up wheel?
- Is there a reliable (and not too difficult) method to measure spoke length on a built-up wheel?
#2
Senior Member
Join Date: Dec 2010
Location: northern Deep South
Posts: 8,901
Bikes: Fuji Touring, Novara Randonee
Mentioned: 36 Post(s)
Tagged: 0 Thread(s)
Quoted: 2604 Post(s)
Liked 1,928 Times
in
1,210 Posts
For (2), take a spoke off and measure it. Better yet, on a rear wheel, take one from each side off and measure it. Make sure you replace the first one and re-true before messing things up royally by taking two off at once.
I'd suggest getting new rims, while you're at it. Compared to the cost of a dyno hub, it doesn't add much, but it'll cut your down time way down.
I'd suggest getting new rims, while you're at it. Compared to the cost of a dyno hub, it doesn't add much, but it'll cut your down time way down.
#3
Senior Member
Join Date: Feb 2012
Location: Rochester, NY
Posts: 18,073
Bikes: Stewart S&S coupled sport tourer, Stewart Sunday light, Stewart Commuting, Stewart Touring, Co Motion Tandem, Stewart 3-Spd, Stewart Track, Fuji Finest, Mongoose Tomac ATB, GT Bravado ATB, JCP Folder, Stewart 650B ATB
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 4201 Post(s)
Liked 3,857 Times
in
2,305 Posts
With skill and experience a lot of "uncommon" measuring of stuff can be spot on. But lacking that pull a spoke or two and reverse math the ERD. Andy
__________________
AndrewRStewart
AndrewRStewart
Likes For Andrew R Stewart:
#4
Senior Member
Join Date: Dec 2019
Location: South Shore of Long Island
Posts: 2,799
Bikes: 2010 Carrera Volans, 2015 C-Dale Trail 2sl, 2017 Raleigh Rush Hour, 2017 Blue Proseccio, 1992 Giant Perigee, 80s Gitane Rallye Tandem
Mentioned: 12 Post(s)
Tagged: 0 Thread(s)
Quoted: 1088 Post(s)
Liked 1,024 Times
in
723 Posts
Isn't hard if you have one of the sewing tape measures, they come in metric. Take a longish piece of cardboard from one of those amazon boxes you probably have lying about, cut out an arch from it so it can sit over the hub and axle, mark the inside edges of the rim on the cardboard (this is easiest if the tire is off and the cardboard edge can sit right on the rim) from two spots directly opposite each other. Measure the distance between the marks, and add 3-4mm to the length to cover the thickness of the rim and get the threads into the spoke nipples.
#5
Junior Member
Thread Starter
Using new rims would also tempt me to further expand the scope of the project: once I'm buying new rims, I might as well replace the rear hub, too...
#6
Senior member
Join Date: Oct 2004
Location: Oakville Ontario
Posts: 8,117
Mentioned: 25 Post(s)
Tagged: 0 Thread(s)
Quoted: 943 Post(s)
Liked 658 Times
in
371 Posts
I've considered that option, but rim availability seems pretty spotty these days. Any recommendations for an available, reasonably-priced 32-hole 650b disc rim for 42-47mm tires?
Using new rims would also tempt me to further expand the scope of the project: once I'm buying new rims, I might as well replace the rear hub, too...
Using new rims would also tempt me to further expand the scope of the project: once I'm buying new rims, I might as well replace the rear hub, too...
#7
Half way there
Join Date: Sep 2015
Location: North Carolina
Posts: 2,957
Bikes: Many, and the list changes frequently
Mentioned: 5 Post(s)
Tagged: 0 Thread(s)
Quoted: 986 Post(s)
Liked 880 Times
in
527 Posts
Personally, I would skip rebuilding the back wheel. The marginal gains are just not worth the effort. OTOH, if you just want the practice or if you have some damaged spokes, go for it.
What hub are you planning to use? I've used Shimano, Sturmey, and Shutter Precision (which I like the best). SON was a bit too expensive for my budget.
What hub are you planning to use? I've used Shimano, Sturmey, and Shutter Precision (which I like the best). SON was a bit too expensive for my budget.
#8
Mad bike riding scientist
Join Date: Nov 2004
Location: Denver, CO
Posts: 27,362
Bikes: Some silver ones, a red one, a black and orange one, and a few titanium ones
Mentioned: 152 Post(s)
Tagged: 1 Thread(s)
Quoted: 6219 Post(s)
Liked 4,217 Times
in
2,364 Posts
I'm planning on using my existing rims (Alex MD-21), and while I'm rebuilding my front wheel, I figure I'll go ahead and re-spoke the rear wheel, both to replace the straight-gauge spokes with butted ones and to match the front. I know from my last pair (that I used Alex Adventurer 2 rims on) that the manufacturer's published ERD was 4mm less than what I measured, so I don't want to rely on the published ERD for these rims.
The other thing to consider is how much of a difference will it really make? Using the ERD for a 622mm Alex MD-21 of 608mm and an ERD that is 4mm less (604mm), Prowheel Builder’s spoke calculator returns lengths of 298mm and 296mm, respectively, for the two ERDs. Often I’ve had to compromise on spoke length of about the difference due to availability. I’d probably err on the long side rather than the short one, however.
If you really have to let your OCD kick in, you could measure from the j-bent to the outside of the rim, then measure from the spoke end to the outside of the rim and subtract the difference. Do it more than once (or even twice or even 3 times) and average the results. But that’s a lot of work and is likely to have a whole lot of variance. Probably more than just going with the manufacturer’s ERD
__________________
Stuart Black
Plan Epsilon Around Lake Michigan in the era of Covid
Old School…When It Wasn’t Ancient bikepacking
Gold Fever Three days of dirt in Colorado
Pokin' around the Poconos A cold ride around Lake Erie
Dinosaurs in Colorado A mountain bike guide to the Purgatory Canyon dinosaur trackway
Solo Without Pie. The search for pie in the Midwest.
Picking the Scablands. Washington and Oregon, 2005. Pie and spiders on the Columbia River!
Stuart Black
Plan Epsilon Around Lake Michigan in the era of Covid
Old School…When It Wasn’t Ancient bikepacking
Gold Fever Three days of dirt in Colorado
Pokin' around the Poconos A cold ride around Lake Erie
Dinosaurs in Colorado A mountain bike guide to the Purgatory Canyon dinosaur trackway
Solo Without Pie. The search for pie in the Midwest.
Picking the Scablands. Washington and Oregon, 2005. Pie and spiders on the Columbia River!
#9
Junior Member
Thread Starter
Personally, I would skip rebuilding the back wheel. The marginal gains are just not worth the effort. OTOH, if you just want the practice or if you have some damaged spokes, go for it.
What hub are you planning to use? I've used Shimano, Sturmey, and Shutter Precision (which I like the best). SON was a bit too expensive for my budget.
What hub are you planning to use? I've used Shimano, Sturmey, and Shutter Precision (which I like the best). SON was a bit too expensive for my budget.
As far as hubs, I’ve got a Kasai FS on the way. I’m a little leery of components that need to be shipped overseas for service, even if that service isn’t likely to happen soon. The serviceability aspect was enough for me to finally give it a shot. (I can’t quite bring myself to shell out for a SON either.)
#10
Junior Member
Thread Starter
The other thing to consider is how much of a difference will it really make? Using the ERD for a 622mm Alex MD-21 of 608mm and an ERD that is 4mm less (604mm), Prowheel Builder’s spoke calculator returns lengths of 298mm and 296mm, respectively, for the two ERDs. Often I’ve had to compromise on spoke length of about the difference due to availability. I’d probably err on the long side rather than the short one, however.
Musson said not to trust the mfr and to take my own measurements, so that’s what I did and it worked. I figured I’d do the same thing this go ‘round, but using the mfr specs would be easier, and you’re absolutely right that trying to measure a built rim by adding and subtracting several measurements would probably be less reliable than the published numbers. Tolerance stacking in action!
#11
aged to perfection
Join Date: Jun 2009
Location: PacNW
Posts: 1,814
Bikes: Dinucci Allez 2.0, Richard Sachs, Alex Singer, Serotta, Masi GC, Raleigh Pro Mk.1, Hetchins, etc
Mentioned: 24 Post(s)
Tagged: 0 Thread(s)
Quoted: 837 Post(s)
Liked 1,258 Times
in
663 Posts
Tolerance stacking or uncertainty stacking, exactly. Going to be really hard to come up with ERD or spoke length measurements by measuring a built wheel.
I always measure ERD myself. Errors of 2-3 mm are not uncommon. On the DTs in particular they may be using the proprietary nips (Squorx) as the basis of measurement.
you can make up your own ERD measuring tools as shown. Thread nips onto 2 spokes and cut them at exactly 250 mm. Drop them into 2 rim holes 180 deg. apart. Measure the gap as shown and add that to 500.
/markp
I always measure ERD myself. Errors of 2-3 mm are not uncommon. On the DTs in particular they may be using the proprietary nips (Squorx) as the basis of measurement.
you can make up your own ERD measuring tools as shown. Thread nips onto 2 spokes and cut them at exactly 250 mm. Drop them into 2 rim holes 180 deg. apart. Measure the gap as shown and add that to 500.
/markp
#12
Junior Member
Thread Starter
As far as my original question goes, I found that Musson describes how to measure the ERD of a built rim in his book. He says to measure the OD of the rim by rolling 1 revolution on a flat surface, measuring that distance, and dividing by pi. Next, measure the distance from the rim to the top of a nipple. Subtract twice that distance and then subtract another 2mm to get to the bottom of the slot in the nipple.
I came out with an answer that was off from the published ERD by 2.8mm. Maybe close enough, but I think I'll just make this easier on myself.
Tolerance stacking or uncertainty stacking, exactly. Going to be really hard to come up with ERD or spoke length measurements by measuring a built wheel.
I always measure ERD myself. Errors of 2-3 mm are not uncommon. On the DTs in particular they may be using the proprietary nips (Squorx) as the basis of measurement.
you can make up your own ERD measuring tools as shown. Thread nips onto 2 spokes and cut them at exactly 250 mm. Drop them into 2 rim holes 180 deg. apart. Measure the gap as shown and add that to 500.
/markp
I always measure ERD myself. Errors of 2-3 mm are not uncommon. On the DTs in particular they may be using the proprietary nips (Squorx) as the basis of measurement.
you can make up your own ERD measuring tools as shown. Thread nips onto 2 spokes and cut them at exactly 250 mm. Drop them into 2 rim holes 180 deg. apart. Measure the gap as shown and add that to 500.
/markp