Stem size for switch to mustache handlebars from drop bars
#1
Senior Member
Thread Starter
Join Date: Oct 2010
Posts: 1,251
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 0 Post(s)
Likes: 0
Liked 0 Times
in
0 Posts
Stem size for switch to mustache handlebars from drop bars
I ride a 56cm Cross Check with an eTT of 570 and a 100mm stem, for a total of 670mm reach. My REI sizing said my cockpit length is 660. I've often felt that my frame is a little long for my comfort, so I'm switching from drop bars to mustache handlebars. I've heard that m'bars afford a more upright riding position. I've also heard that they elongate the reach. Contradictory statements, right? Well, I don't know which to believe but I heard it on BFwhere everyone's opinion is truth. Anyways, sizing down...I want to know what size stem would be most appropriate. I think my drop bars would be okay with a 90mm stem or even an 80mm for more of an upright position when riding the tops. Since I don't know what to believe about m'bars, I don't know what size stem I should get. I was thinking of getting a 70mm for a reach of 640mm, 30mm less than my current set up. Is that going to be too short?
#2
Low car diet
Join Date: Aug 2007
Location: Corvallis, OR, USA
Posts: 2,407
Bikes: 2006 Windsor Dover w/105, 2007 GT Avalanche w/XT, 1995 Trek 820 setup for touring, 201? Yeah single-speed folder, 199? Huffy tandem.
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 2 Post(s)
Likes: 0
Liked 4 Times
in
4 Posts
The primary hand position for moustache bars is in the hooks, as opposed to on the hoods for drop bars. You'll probably want to have the stem much higher and a little closer.
If the current bars are serving you well, other than that you feel a bit stretched out, what about keeping it and shortening the stem by 10mm since that'd put your overall reach in line with your fitting?
If the current bars are serving you well, other than that you feel a bit stretched out, what about keeping it and shortening the stem by 10mm since that'd put your overall reach in line with your fitting?
#3
Banned
Yes, the bars bend forward, significantly and a very slight drop..
I have used a tall up angled stem with a fairly short extension .
Consider level with the saddle a starting point for height..
though you may think better of your drop bars
if they were higher and nearer, as well .
My Bike with the mustache bars on it , has a threaded fork.
the stem is an 8 Nitto Dirt drop
off a MB1 take off from the 80's
the 8 is measured up at a 45 degree angle, following the stem Rise,
so its even shorter horizontally than the numbers suggest.
I have used a tall up angled stem with a fairly short extension .
Consider level with the saddle a starting point for height..
though you may think better of your drop bars
if they were higher and nearer, as well .
My Bike with the mustache bars on it , has a threaded fork.
the stem is an 8 Nitto Dirt drop
off a MB1 take off from the 80's
the 8 is measured up at a 45 degree angle, following the stem Rise,
so its even shorter horizontally than the numbers suggest.
Last edited by fietsbob; 01-11-12 at 10:24 PM.
#4
Senior Member
Thread Starter
Join Date: Oct 2010
Posts: 1,251
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 0 Post(s)
Likes: 0
Liked 0 Times
in
0 Posts
Yea I could just shorten the stem and keep my drop bars but a part of me really wants to give my bike a make over with complete different handlebars and chrome accents. So between a 70, 80, or 90mm stem?...90 giving me my 660mm cockpit length.
#5
Banned
So between a 70, 80, or 90mm stem?
go to a bike shop with all 3 in stock, and try them ... ride around the block a few times
threadless stems are a quick swap.
QBP/Dimension has angle adjustable stems .. they're black , maybe that will suit.
Last edited by fietsbob; 01-11-12 at 10:36 PM.
Thread
Thread Starter
Forum
Replies
Last Post
johnbanaag
Singlespeed & Fixed Gear
5
06-10-14 05:24 AM
kiltedcelt
Long Distance Competition/Ultracycling, Randonneuring and Endurance Cycling
14
07-17-11 10:52 PM