P-clamps issue
#1
Junior Member
Thread Starter
Join Date: Jul 2021
Posts: 12
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 6 Post(s)
Liked 0 Times
in
0 Posts
P-clamps issue
I want to attach a rack to a bicycle but the bike frame does not have eyelets. I plan to use p-clamps but the the frame at the clamping point is not completely round. It flattens out about where the wheel begins. Can a p-clamp tighten on a more rectangular surface?
#2
Senior Member
Join Date: Mar 2019
Posts: 1,606
Mentioned: 8 Post(s)
Tagged: 0 Thread(s)
Quoted: 581 Post(s)
Liked 921 Times
in
518 Posts
Probably, yes, but it might move around a bit and require tightening after a few rides and it has found its natural resting place. However, P clamps are not great for holding a load - they will probably eventually break if you are using them as structural supports at dropouts. This is not a problem with using p clamps on the seat stays for the upper supports because these don't hold any weight. But at the dropouts they're best for only light loads.
Likes For ClydeClydeson:
#3
Clark W. Griswold
Join Date: Mar 2014
Location: ,location, location
Posts: 13,506
Bikes: Foundry Chilkoot Ti W/Ultegra Di2, Salsa Timberjack Ti, Cinelli Mash Work RandoCross Fun Time Machine, 1x9 XT Parts Hybrid, Co-Motion Cascadia, Specialized Langster, Phil Wood Apple VeloXS Frame (w/DA 7400), R+M Supercharger2 Rohloff, Habanero Ti 26
Mentioned: 54 Post(s)
Tagged: 0 Thread(s)
Quoted: 4348 Post(s)
Liked 3,985 Times
in
2,661 Posts
What kind of bike are you clamping on? Carbon is a no go and if the frame isn't designed for a rack probably that is the manufacturer saying maybe not a rack. Remember if you do end up using p-clamps you will likely void the warranty, and won't be able to hold as much weight.
#4
Senior Member
Join Date: Jun 2015
Location: South Korea
Posts: 783
Bikes: Merida Speeder
Mentioned: 4 Post(s)
Tagged: 0 Thread(s)
Quoted: 233 Post(s)
Liked 165 Times
in
115 Posts
For road bikes, look at something like this:
https://www.axiomgear.com/products/r...iner-road-dlx/
It attaches via the rear QR skewer and the seatstay bridge eyelet.
https://www.axiomgear.com/products/r...iner-road-dlx/
It attaches via the rear QR skewer and the seatstay bridge eyelet.
Likes For PDKL45:
#5
Senior Member
Join Date: May 2005
Location: northWET washington
Posts: 1,197
Mentioned: 3 Post(s)
Tagged: 0 Thread(s)
Quoted: 383 Post(s)
Liked 690 Times
in
396 Posts
For road bikes, look at something like this:
https://www.axiomgear.com/products/r...iner-road-dlx/
It attaches via the rear QR skewer and the seatstay bridge eyelet.
https://www.axiomgear.com/products/r...iner-road-dlx/
It attaches via the rear QR skewer and the seatstay bridge eyelet.
Likes For kahn:
#6
Senior Member
Join Date: Jul 2008
Location: 25 miles northwest of Boston
Posts: 29,549
Bikes: Bottecchia Sprint, GT Timberline 29r, Marin Muirwoods 29er, Trek FX Alpha 7.0
Mentioned: 112 Post(s)
Tagged: 0 Thread(s)
Quoted: 5224 Post(s)
Liked 3,581 Times
in
2,342 Posts
one might use some padding around the frame part so that the p-clamp will be snug
this is a home made clamp, on the right
I use p-clamps to hold the rack on my road bike, but it's not ideal. they are strong enough but there are more elegant ways to do it
this is one of mine. it is not quite tight enough but there is minimal movement due to it's location, but the frame does show some wear
this is a home made clamp, on the right
I use p-clamps to hold the rack on my road bike, but it's not ideal. they are strong enough but there are more elegant ways to do it
this is one of mine. it is not quite tight enough but there is minimal movement due to it's location, but the frame does show some wear
Last edited by rumrunn6; 09-14-21 at 01:09 PM.
Likes For rumrunn6:
#7
Live not by lies.
Join Date: Nov 2020
Posts: 1,306
Bikes: BigBox bikes.
Mentioned: 3 Post(s)
Tagged: 0 Thread(s)
Quoted: 860 Post(s)
Liked 784 Times
in
582 Posts
Use them at work.
Yes they’re strong enough.
But all the work applications clamp around much thicker wall thickness than a bike frame. FWIW.
Also, if clamping around something not actually round, might have to experiment with the next size down than you might think and re-bending and re-tightening after awhile.
Yes they’re strong enough.
But all the work applications clamp around much thicker wall thickness than a bike frame. FWIW.
Also, if clamping around something not actually round, might have to experiment with the next size down than you might think and re-bending and re-tightening after awhile.