Go Back  Bike Forums > Bike Forums > Bicycle Mechanics
Reload this Page >

Misaligned Rear Wheel. Frame/Dropout issue?

Notices
Bicycle Mechanics Broken bottom bracket? Tacoed wheel? If you're having problems with your bicycle, or just need help fixing a flat, drop in here for the latest on bicycle mechanics & bicycle maintenance.

Misaligned Rear Wheel. Frame/Dropout issue?

Old 01-10-21, 05:14 AM
  #26  
02Giant 
Senior Member
 
Join Date: Jan 2011
Posts: 2,977
Mentioned: 6 Post(s)
Tagged: 0 Thread(s)
Quoted: 1638 Post(s)
Liked 741 Times in 495 Posts
Originally Posted by Racing Dan
I own a bike with very sloppy dropouts on the rear. To align the back wheel I need to flip the bike up side down and hold the wheel in position while tightening the QR. Else it all misaligned. It does stay put tho, so not a big deal, just a minor annoyance that points to sloppy manufacturing and engineering.
Originally Posted by Jean_TX
I have the same problem with my old DiamondBack steel frame bike, and my fix is the same as above. Easy to do, but it is annoying that the frame/dropouts were so poorly made.
I have had a few bikes over the years with the same issue. I center the wheel, lock it down, and ride.
__________________
nine mile skid on a ten mile ride
02Giant is offline  
Old 01-10-21, 08:16 AM
  #27  
L134 
Senior Member
 
Join Date: Dec 2015
Location: San Diego
Posts: 704

Bikes: 1978 Bruce Gordon, 1977 Lippy, 199? Lippy tandem, Bike Friday NWT, 1982 Trek 720, 2012 Rivendell Atlantis, 1983 Bianchi Specialissima?

Mentioned: 11 Post(s)
Tagged: 0 Thread(s)
Quoted: 345 Post(s)
Liked 170 Times in 105 Posts
Originally Posted by Andrew R Stewart
In a manor of function the trued and dished wheel acts as the gage. No need to do any other measure to see if the wheel sits off plane WRT the front triangle. One's eyes can see the gaps and overlaps that frame alignment works with. Of course knowing how to interpret what you see...

Before I would consider filing anything I would want to do a full frame alignment lookover. I will not be surprised if there's other issues elsewhere. But this means a rather deep breakdown of the bike to pretty much just the frame and separate fork, not something many will want to do. So I also won't be surprised if the OP only deals with the rear end. I hope this is enough change to make the bike handle/track better enough. Andy
And, I don’t disagree. I believe OP stated 2 different trued and dished wheels had the same problem. I think he said he checked the rear triangle using the string method and it was centered. I never advocated filing. My only mention of filing was posed as a question for those more knowledgable of how to deal with this if his stays are of unequal length AND he has vertical dropouts. If his dropouts are horizontal, the fix is as easy as 02Giant states - center it and ride. No need to measure the stays other than to satisfy one’s curiosity as to how this situation can be. It seemed to me that such curiosity did exist (but maybe it is only my own) therefore I suggested measuring the stays.
L134 is offline  
Old 01-10-21, 03:28 PM
  #28  
mitchmellow62
Full Member
 
Join Date: Aug 2014
Posts: 286
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 94 Post(s)
Liked 56 Times in 41 Posts
I crawled up in the attic and located the 700c rear wheel spaced at 126mm (actually measured 127). It started life on a 1991 Cannondale from the same lbs and was a frame/fork build they performed. The wheel is straight and true but I think the dish is a little off (maybe 2 mm; I don't have the dishing tool/gauge). Flipping it in the dropouts and dealing with 2 variables is too much for this pea brain. So I went back to the original 27" slightly out of true wheel. To be consistent I did all the measurement/comparison at the air valve. I get results that are identical. The rim is to the left at the chain and seat stays when in correctly or when flipped. It is greater at the chain stay. I'm not sure what to make of this. I've owned mine since new and it has never been crashed or dropped. I upgraded to 7 spd index shifting and it worked well. Both bikes are Schwinn Voyageurs but they are different years and have different geometries. The '88: Wheelbase 42.25", HT angle 72, ST angle 74. My '89: Wheelbase 41.3", HT angle 72.5, ST angle 72.5. I can't find any other measurements. Is this coincidence or manufacturer error?
mitchmellow62 is offline  
Old 01-10-21, 07:00 PM
  #29  
mitchmellow62
Full Member
 
Join Date: Aug 2014
Posts: 286
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 94 Post(s)
Liked 56 Times in 41 Posts
My '89 just failed the string alignment test. Different problem. Never mind.
mitchmellow62 is offline  
Old 01-19-21, 09:36 AM
  #30  
drewfio
Junior Member
Thread Starter
 
Join Date: Jun 2020
Location: New York, NY
Posts: 182

Bikes: Mostly 80's Japanese built road and touring bikes

Mentioned: 1 Post(s)
Tagged: 0 Thread(s)
Quoted: 62 Post(s)
Liked 77 Times in 25 Posts
An update:

After contacting several more bike shops, most of which did not want to take on frame repair work, I found one that would—Harvest Cyclery in Brooklyn. When I brought the bike in, they were pretty confident they could straighten the frame out. I also asked them to remove pedals which were rusted and seized on when I got the bike, that I had been struggling to get off. Two days later they called and said both were done. When I got there it looked pretty straight! I also measured with calipers when I got it back home, and it is equal. And most importantly, I took it for a ride, and it rides straight now.

The guy I left the bike with, who was the one who performed the repair, was not working when I picked it up, so I didn't get to talk about the details of the operation. But from what I could gather from our original conversation, my string test might have been off, and assuming his first impression diagnosis was confirmed, he was going to bend the stays slightly.

Anyway, I'm pretty happy to have this bike on the road.
drewfio is offline  
Likes For drewfio:
Old 01-23-21, 06:03 PM
  #31  
oldbobcat
Senior Member
 
oldbobcat's Avatar
 
Join Date: Jul 2005
Location: Boulder County, CO
Posts: 4,370

Bikes: '80 Masi Gran Criterium, '12 Trek Madone, early '60s Frejus track

Mentioned: 6 Post(s)
Tagged: 0 Thread(s)
Quoted: 508 Post(s)
Liked 434 Times in 331 Posts
The wheel is centered at the brake bridge but cocked to the left at the bottom bracket. That means something whacked the bottom bracket area of the bike from the left or the rear triangle near the axle from the right. Most shops will do "easy" frame alignments like spreading stays or squaring up dropouts, but fixing this requires a degree of skill and torque. Generally, shops don't have that kind of expertise, and the boutique shops don't do enough work on steel to maintain that kind of expertise. To make it worse, it's a Schwinn Voyageur, which hardly justifies stripping the bike to a bare frame and shipping it to Richard Sachs.

If your neighborhood doesn't have an old race-oriented shop who has amechanic who still knows how to align frames, and since it is just a Schwinn Voyageur, my suggestion is this. Remove the wheels, cranks, and bottom bracket. Support the rear dropouts by inserting an old hub of the proper spacing. Lay the bike on its left side, supporting it with wood blocks at the seat lug and head tube. With a friend standing on the seat lug, jump up and down on the bottom bracket and see what happens.

Disclaimer: If this were a vintage Cinelli, I'd be sending it to Richard Sachs.
oldbobcat is offline  
Old 01-25-21, 08:40 PM
  #32  
byrd48
Full Member
 
Join Date: May 2012
Location: Atlanta, GA
Posts: 335

Bikes: Dave Kirk Custom, Clockwork Bikes Custom, Batavus Course Specialized HardRock x2 Trek 700 MultiTrack 1991 Trek 950 SingleTrack. Miyata Three Ten

Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 32 Post(s)
Likes: 0
Liked 1 Time in 1 Post
For the benefit of all others who may land on this thread in the future, it would be great to follow up with that mechanic and relate what they did! 😉
byrd48 is offline  
Old 02-16-21, 08:59 AM
  #33  
drewfio
Junior Member
Thread Starter
 
Join Date: Jun 2020
Location: New York, NY
Posts: 182

Bikes: Mostly 80's Japanese built road and touring bikes

Mentioned: 1 Post(s)
Tagged: 0 Thread(s)
Quoted: 62 Post(s)
Liked 77 Times in 25 Posts
Originally Posted by byrd48
For the benefit of all others who may land on this thread in the future, it would be great to follow up with that mechanic and relate what they did! 😉
I followed up, and indeed the stays were out of alignment laterally. My original string test was inaccurate. So they secured the frame and gently bent the stays back into place.
drewfio is offline  
Likes For drewfio:
Old 02-16-21, 09:58 AM
  #34  
Andrew R Stewart 
Senior Member
 
Andrew R Stewart's Avatar
 
Join Date: Feb 2012
Location: Rochester, NY
Posts: 17,998

Bikes: Stewart S&S coupled sport tourer, Stewart Sunday light, Stewart Commuting, Stewart Touring, Co Motion Tandem, Stewart 3-Spd, Stewart Track, Fuji Finest, Mongoose Tomac ATB, GT Bravado ATB, JCP Folder, Stewart 650B ATB

Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 4171 Post(s)
Liked 3,789 Times in 2,269 Posts
"The wheel is centered at the brake bridge but cocked to the left at the bottom bracket. That means something whacked the bottom bracket area of the bike from the left or the rear triangle near the axle from the right" oldbobcat

What you suggest, an impact that moved the BB (and thus bent the 4 tubes attached to the BB) is far less likely then the frame being built with one chainstay longer then the other.

The OP's final posts have said what I have tried to describe here and in other threads about frame alignment. Knowing how to measure and then what to do to correct is key. A bicycle being ridden is a very complex system. Many parts of this system can, and often does, contribute how the system goes down the road. It is rare that I have found only one issue when dealing with frame alignment or steering/stability issues. This is not to say that correcting what you can understand is wrong, quite the opposite. Just that there's more to alignment then having the rear triangle centered WRT the main triangle, even keeping within the frame only (and disregarding any fork or rider aspects).

I would liked to have had this bike in front of me so I could apply my experience. But as this is a fake world we communicate through (the interweb is all bark with zero bite) all we can offer is barking. Andy
Andrew R Stewart is offline  
Old 02-17-21, 02:46 AM
  #35  
bitpuddle
Junior Member
 
Join Date: Jan 2015
Location: Brooklyn, NY
Posts: 82

Bikes: Cinelli Nemo Tig / Battaglin Power Plus / Moots RCS

Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 26 Post(s)
Liked 18 Times in 13 Posts
Any competent frame builder would be able to cold set the frame if the stays or dropouts are out of alignment. You’d have to decide if the cost is worth it. Shops rarely do this and I’d be cautious of ones that are willing to (it might work out, it might not). As mentioned above, it is best to eliminate wheel dish or some crazy issue with an axle.
bitpuddle is offline  

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


Thread Tools
Search this Thread

Contact Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service -

Copyright © 2024 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.